ARGtek ARG-1220 User manual
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
ARGtek ARG-1220 WLAN Dual Band
AP Router
For 802.11a/b/g/n
POWER KING SPACE
Quick Installation Guide
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
Part I: External Installation Direction
Package Content
AP Router 1
DC 12V Power Adapter 1
Dual Band Antenna 1
PoE DC Injector 1
Paper QIG 1
Manual/QIG CD 1
AP Router Connection
Before installing the router, connect your PC to the internet through your
broadband service.(If there is any problem, contact your ISP.)Then proceed
through the following steps.
1. Turn off your PC(s), cable/(A)DSL modem and the router.
2. Adjust the antenna. Normally, upright is a good place to start.
3. Connect the PC(s) and each switch/hub on your local area network to the
LAN ports on the router.
4. Connect the ADSL/DSL/cable modem to the router WAN port.
5. Connect the power adapter between the power socket on the router and
an electrical outlet. The router will start to work automatically.
6. Turn on your PC(s) and the cable/(A)DSL modem.
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
The Front LED Indicator
AP Router configuration
The AP Router is delivered with the following factory default parameters on the
Ethernet LAN interfaces.
Default IPAddress: 10.10.10.254
Default IP subnet mask: 255.255.255.0
Web login User Name: admin
Web login Password: admin
The device has four operation modes (Gateway/Bridge/WISP/AP Client).
The default IP addresses for the device are 10.10.10.254, so you need to
make sure the IP address of your PC is in the same subnet as the device, such
as 10.10.10.X.
It will take about 55 seconds to complete the boot up sequence after power on.
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
PoE DC Injector Configuration
POE means Power over Ethernet, usually used with Wireless Device.
You can use it to integrate the power and the Ethernet then connected with the
RJ45 cable.
With POE, you can bring the power and Ethernet with long distance as far as
the length of RJ45 cable.
Since you used PoE DC Injector, the cable line won’t perplex you anymore.
Your Access Point & Router are installed conveniently to gain more efficient
bandwidth by yourself.
Less space and electricity limitation, more comfortable wireless life.
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
Part II: Internal Web Management
AP Model Setup (ADSL)
1、Install the antenna & power adapter, and then connect the LAN cable with
LAN port of this equipment. Another side of cable line connects with
network card of computer. Waiting for booting around 20 seconds.
2、Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to
enter the setup frame. If you can’t enter to setup frame, you can try to set
the IP address for 10.10.10.XXX and try to connect again. Otherwise,
please press Reset button around 10 seconds to restore AP and try to
enter again
Select the Operation Mode on the left side of setup frame
1. In Operation Mode, select Gateway and press Apply
2a. In Internet Settings / WAN /, select PPPoE (ADSL) for your WAN
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
Connection Type and enter your User Name & Password which were
presented by your ISOP company. And then press Apply
2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP
and etc. then press Apply
3. In Wireless Settings / Basic, you may change the setting of SSID, and then
press Apply
4. In Wireless Settings / Security, you may change the setting of password,
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
and then press Apply
Finish setting and press Apply, the setting will be completed after rebooting
around 20 seconds.
Note: You have to connect ADSL cable with the WAN port of this equipment.
==========================================================
AP Model Setup (IP Share)
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
1、Install the antenna & power adapter, and then connect the LAN cable with
LAN port of this equipment. Another side of cable line connects with RJ-45
of computer. Waiting for booting around 20 seconds.
2、Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to
enter the setup frame. If you can’t enter to setup frame, you can try to set
the IP address for 10.10.10.XXX and try to connect again. Otherwise,
please press Reset button around 10 seconds to restore AP and try to
enter again
Select the Operation Mode on the left side of setup frame
1. In Operation Mode, please select Bridge. Select AP or Main AP in Wireless
Operation Mode and press Apply
2 In Internet Setting/LAN/, you may change the setting of IP address, DHCP
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
and etc. then press Apply
3 In Wireless Settings / Basic, you may change the setting of SSID, and then
press Apply
4. In Wireless Settings / Security, you may change the setting of password,
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
and then press Apply
Finish setting and press Apply, the setting will be completed after rebooting
around 20 seconds.
Note: You have to connect cable line with the LAN port of this equipment.
==========================================================
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
3-4. In Operation Mode, select Wireless ISP and press Next>>
3-5. In Time Zone Setting, if you don’t need any change, please press Next>>
3-6. In LAN Interface Setup, you may change the setting of IP address, DHCP
and etc. then press Next>>
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
3-7. In WAN Interface Setup, select PPPoE for your connection of WAN
Access Type and enter User Name & Password which presented by your
ISOP. And then press Next>>
Note: Connecting Telecom Access Point usually is based on PPPoE, but in
general, a pure connection is via Static IP or DHCP
Client.
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
3-8. In Wireless Basic Setting, select Client for your Mode and change your
SSID setup, then press Next>>
3-9. In Wireless Security, select your setup of wireless security (WPA) and
press Finished to reboot around 20 seconds, and wait for 20 seconds for
reboot.
ARGtekCommunicationInc.www.argtek.com
E‐Mail:[email protected]Tel:+886‐2‐2999‐6958 Fax:+886‐2‐2999‐7742
Note: Please connect cable line with LAN port when you use WISP
Mode.
Other ARGtek Wireless Router manuals
