Ariens A149K21 (96136000) User manual

A149K21
(96136000)
Owner's Manual
435759 Rev. 1 03.31.10 BY •EspaSol, p. 18
Printed in U.S.A.

Safety Rules .......................................... 2-4
Product Specifications .............................. 4
Assembly /Pre-Operation ........................ 5
Operation ............................................... 6-9
Maintenance Schedule ........................... 10
Maintenance ...................................... 10-I2
Service and Adjustments ........................ 13
Storage .............................................. 14-15
Troubleshooting ................................. 15-16
Repair Parts....................................... 32-33
Warranty ................................................. 36
IMPORTANT" This cutting machine is
capable of amputating hands and feet and
throwing objects. Failure to observe the
following safety instructions could result in
serious injury or death.
,&Look for this symbol to point out impor-
tant safety precautions, It means
CAUTION!![ BECOME ALERT!!!
YOUR SAFETY IS INVOLVED,
,& WARNING: tn order to prevent ac-
cidental starting when setting up, trans-
porting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot come in contact
with plug.
,&WARNING; Engine exhaust, some of its •
constituents, andcertain vehicle components
contain or emit chemicals known tothe State
of California tocause cancer andbirthdefects ,
or other reproductive harm.
,&WARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm. '#'#ash
hands after handling.
,& CAUTION; Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped, To avoid severe burns on
contact, stay away from these areas.
2
I, GENERAL OPERATION
• Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thoroughly
familiar with the controls and the proper
use of the machine before starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times.
• Only allow responsible individuals, who
are familiar with the instructions, to oper-
ate the machine.
• Clear the area of objects such as rocks,
toys, wire, bones, sticks, etc., which
could be picked up and thrown by blade.
• Be sure the area isclear of other people
before mowing. Stop machine if anyone
enters the area.
Do not operate the mower when bare-
foot or wearing open sandals. Always
wear substantial foot wear.
Do not pull mower backwards unless
absolutely necessary. Always took down
and behind before and while moving
backwards.
• Never direct discharged material toward
anyone. Avoid discharging material
against a wall or obstruction. Material
may richochet back toward the opera-
tor, Stop the blade when crossing gravel
surfaces,
•Do notoperatethe mowerwithout
proper guards,plates, grass catcheror
other safety protective devices in place.
See manufacturer's instructions for
proper operationand installationof
accessories, Only use accessories ap-
proved by the manufacturer.
Stop the blade(s) when crossing gravel
drives, walks, or roads.
Stop the engine (motor) whenever you
leave the equipment, before cleaning the
mower or unclogging the chute.
Shut the engine (motor) off and wait until
the blade comes to complete stop before
removing grass catcher.
Mow only in daylight or good artificial
light.

• Do not operate the machine while under
the influence of alcohol or drugs.
• Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle; walk, never run.
•Disengage the self-propelled mech-
anism or drive clutch on mowers so
equipped before starting the engine.
•If the equipment should start to vibrate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibra-
tion is generally a warning of trouble.
•Always wear safety goggles or safety
glasses with side shields when operating
mower.
U, SLOPE OPERATION
Slopes are a major factor related to slip &
fall accidents which can result in severe
{njury.All slopes require extra caution. If
you feel uneasy on aslope, do not mow it.
DO"
° Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
•Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
•Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
•Do not mow on wet grass. Reduced
footing could cause slipping.
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the machine
and the mowing activity. Never assume
that children will remain where you last
saw them.
• Keep children out of the trimming area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
•Before and while walking backwards,
look behind and down for small children.
•Never allow children to operate the
machine.
° Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SAFE HANDLING OF GASOLINE
Use extreme care Jr1handlinggasoline.
Gasoline is extremely flammable and the
vapors are explosive.
oExtinguish all cigarettes, cigars, pipes
and other sources of ignition.
-Use only an approved container.
•Never remove gas cap or add fuel with
the engine running. Allow engine to cool
before refueling.
°Never refuel the machine indoors.
• Never store the machine or fuel contain-
er where there is an open flame, spark
or pilot light such as a water heater or
on other appliances.
•Never fill containers inside a vehicle, on
a truck or trailer bed with a plastic liner,
Always place containerson the ground
away from your vehicle before filling.
• Remove gas-powered equipment from
the truck or trailer and refuel it on the
ground. Ifthis is not possible, then
refuel such equipment with aportable
container, rather than from a gasoline
dispenser nozzle.
•Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times until fueling is complete. Do
not use a nozzle lock-open device.
•Iffuel is spilled on clothing, change
clothing immediately.
•Never overfill fuel tank. Replace gas
cap and tighten securely.
V. GENERAL SERVICE
• Never run a machine inside a closed
area.
•Never make adjustments or repairs with
the engine (motor) running. Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting.
•Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip-
ment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
•Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spitFage.Allow machine to cool before
storing.
•Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
•Never attempt to make wheel height
adjustments while the engine isrunning.

° Grasscatchercomponentsaresubject
towear,damage,anddeterioration,
whichcouldexposemovingpartsor
allowobjectstobethrown.Frequently
checkcomponentsandreplacewith
manufacturer'srecommendedparts,
whennecessary,
• Mowerbladesaresharpandcancut.
Wraptheblade(s)orweargloves,and
useextracautionwhenservicingthem.
• Donotchangetheenginegovernorset-
tingoroverspeedtheengine.
° Maintainorreplacesafetyandinstruc-
tionlabels,asnecessary,
&WARNING:Thislawnmowerisequippedwithaninternalcombustionengineand
shouldnotbeusedonornearanyunimprovedforest-covered,brush-coveredor
grass-coveredlandunlesstheengine's exhaust system is equipped with aspark
arrester meeting applicable local or state laws (ifany). If a spark arrester is used, it
should be maintained in effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws, Federal laws apply on
federal lands.
Serial Number:
Date of Purchase;
Gasoline Capacity /Type: 1.5 Quarts (Unleaded Regular)
Oil Capacity: 20 Ounces
Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 10W-30 (below 32°F)
Spark Plug: Champion 8815 (Gap: .030")
Blade Bolt Torque: 35-40 ft. lbs.
The model and serial numbers will be found on a decal on the rear of the lawn mower
housing, Record both serial number and date of purchase in space 3rovided above.
4

Read these instructions and this manual in
its entirety before you attempt to assemble
or operate your new lawn mower.
IMPORTANT: This lawn mower is shipped
WITHOUT OILOR GASOLINE inthe engine.
Your new lawn mower has been assem-
bled at the factory with the exception of
those parts left unassembied for shipping
purposes, To ensure safe and proper
operation of your lawn mower, all parts
and hardware you assemble must be tight-
ened securely. Use the correct tools as
necessary to ensure proper tightness. All
parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have
been placed in the parts bag.
TO REMOVE MOWER FROM CARTON
I. Remove loose parts includedwith
mower.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials except
padding between upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of cartonand
check carton thoroughly for additional
loose parts.
HOW TO SET UP YOUR MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefullyso
as not to pinchor damage control cables.
1. Raise handlesuntillowerhandlesection
locksinto place in mowing position.
2. Remove protective padding, raise up-
perhandle section intoplace on lower
handleand tightenboth handle knobs.
3. Remove handie padding holding
operatorpresence controlbar to upper
handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "AD-
JUST HANDLE" in the Service and Adjust-
ments section of this manual.
Operator MOWING
POSITION
controlbar
Upper
UP handle
Handle
knob
Lowerhandle
TO ASSEMBLE GRASS CATCHER
1, Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2. Slip vinyl bindings over frame.
NOTE: Ifvinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let itdry before using. Frame
Vinyl Frame
bindings opening
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be
used asa muicher. Toconvert tobagging or
discharging,see 'TO CONVERT MOWER"
in the Operation section of this manual
5

KNOW YOUR LAWN MOWER
READ TH_SOWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments. Save this manual for
future reference.
lllllll,llll,l,iillillHll,,,lll,ll,llllll
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNtNG ON OFF AND FEET AWAY
lll,iHlllll,ll,llIHlIHII
-Operator presence controlbar
Starter
handle Gasoline fillercap
Grass
catchc
Air filter
Engine oil Housing
with dipstick
Mulcher door
adjuster
(oneachwheel)
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the engine. iiiii ui ii [i i
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Com-
mission. AWARNING: The blade turns when the engine is running.
iiiiiiiiiiiiiiiiiiiiiiiiiii1[ iiiiiiiiiiiiiiiiiiiiiiii luliiiiii i1[i iii i i II iiiii i
Operator presence control bar - must Mulcher door- allows conversion to
be held down to the handle to start the discharging or bagging operation.
engine. Release to stop the engine. Starter handle - used for starting engine.
6

Theoperationofanylawn
mowercanresultinforeign
objectsthrownintotheeyes,
which can result in severe
eye damage. Always wear
safety glasses or eye shields while oper-
ating your lawn mower or performing any
adjustments or repairs. We recommend a
standard safetyglasses orwide vision safety
mask worn over spectacles.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
Engine speed was set at the factory for
optimum performance. Itis not adjustable.
ENGINE ZONE CONTROL
_LCAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury. Do not under
any circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running.
• Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
TO ADJUST CUTTING HEIGHT
Raise wheels for low cut and lower wheels
for high cut, adjust cutting height tosuit
your requirements. Medium position is
best for most lawns.
° To change cutting height, squeeze ad-
juster lever toward wheel. Move wheel
upor down to suit your requirements. Be
sure all wheels are in the same setting.
NOTE; Adjuster isproperly positioned when
plate tab inserts into hole in lever. Also, 9-
position adjusters (ifsoequipped) allow lever
to be positioned between the plate tabs.
LEVERBACKWARD Platetab
TO LOWERMOWER
LEVERFORWARDTO RAISEMOWER Lever
TO CONVERT MOWER
Your lawn mower was shipped ready to be
used as a mulcher. Toconvert to bagging
or discharging:
REAR BAGGING
, Lift rear door of the lawn mower and
place the grass catcher frame hooks
onto the door pivot pins.
-To convert to mulching or discharging
operation, remove grass catcher and
close rear door.
Pivot "Rear Grass
catcher
handle
Catcherframehook
SIDE DISCHARGING
•Rear doormust be closed.
°Open mulcher door and install dis-
charge deflector under door as shown.
• Mower isnow ready for discharging
operation.
° To convert to mulching or bagging opera-
tion, discharge deflector must be removed
and mulcher door must be closed.
SIMPLE STEPS TO REMEMBER WHEN
CONVERTING YOUR LAWN MOWER
FOR MULCHING -
1. Rear door closed.
2, Mutcher door closed,
FOR REAR BAGGING -
1. Grass catcher installed.
2. Mu[cher door closed.
FOR SIDE DISCHARGING -
1. Rear door closed.
Discharge deflector installed.
AUTiON: Do not run your lawn mower
without rear door closed, clipping deflector
or approved grass catcher in place. Never
attempt to operate the lawn mower with the
rear door removed or propped open.
Open mulchLdoor
Install
discharg,
7 deflector

MOWERISNOWREADYFOR
DISCHARGINGOPERATION
TO EMPTY GRASS CATCHER
1. Liftup on grass catcher using the
frame handle,
2. Remove grass catcher with clippings
from under lawn mower handle,
3. Empty clippings from bag,
NOTE: Do not drag the bag when empty-
ing; it will cause unnecessary wear.
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower isshipped without oil in
the engine. For type and grade of oil to
use, see "ENGINE" in the Maintenance
section ofthis manual.
_1_CAUTION: DO NOT overfill engine with
oil, or it wiltsmoke heavily from the muffler
on startup,
1, Be sure lawnmower is level.
2. Remove oil dipstick from oil fill spout,
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine.
NOTE: Initial oil fill requires only 18 oz.
due to residual oil in engine from the
manufacturers 100% quality testing.
When changing oil you may need 20 oz,
4, Insert and tighten dipstick.
IMPORTANT:
• Check oil levelbefore each use. Add oil
if needed, Fill to full line on dipstick.
• Change the oil after every 25 hours of
operation or each season, You may
need to change the oil more often
under dusty, dirty conditions. See 'q'O
CHANGE ENGINE OIL" in the Mainte-
nance section of this manual.
filler cap
Engine
oil cap
ADD GAsoLINE
• FIll fue! tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be
used within 30 days to assure fuel fresh-
ness.
ACAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame,
• i, CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or metha-
nol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems,the fuel system
should be emptied before storage of30
days or longer, Empty the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.

TO STOP ENGINE
• To stop engine, release operator pres-
ence controlbar.
TO START ENGINE
NOTE: Due to protective coatingson the
engine, a small amount ofsmoke may be
present duringthe initialuse of the product
and should be considerednormal.
NOTE: Your engineis equipped withan
automatic choke system. No primingor
choking is required before starting.
•To start engine, hold operator presence
control bar down to the handle and pull
starter handle quickly. Do not allow
starter rope to snap back.
MOWING TIPS
CAUTION: Do not use de-thatcher
blade attachments on your mower, Such
attachments are hazardous, willdamage
your mower and could void your warranty.
• Under certain conditions,such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing effort
and to keep from overloading the engine
and leaving clumpsof grass clippings.
tt may also be necessary to reduce
ground speed and/or run the lawn
mower over the area a second time,
• For extremely heavy cutting,reduce the
width of cut by ovedapping previously
cut path and mow slowly.
°For better grass bagging and most cut-
ting conditions, the engine speed should
be set inthe FAST position.
•Pores in cloth grass catchers can
become filled with dirt and dust with use
and catcherswill collectless grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life.
MULCHING MOWING TIPS
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. See "CLEANING" in the
Maintenance section of this manual.
•The special mulching blade will recut
thegrass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and notbe noticed. Also, the
mulched grass wilt biodegrade quickly to
provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut-
ting action of the blades.
•Avoid cutting your lawn when it iswet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area willnot be
exposed to direct sunlight.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades, it the lawn is overgrown
it will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
INt1111_\|1I
MAX 1/3
•Certain types of grass and grass
conditionsmay require that an area be
mulched a second time to completely
hide the clippings. When doing a sec-
ond cut, mow across (perpendicular) to
the first cut path.
• Change your cuttingpattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting
and graining of the lawn.

MAINTENANCE BEFORE AFTER EVERY
EACH EACH 10
SCHEDULE use use HOURS
ii ii
Check for Loose Fasteners
LClean /Inspect Grass Catcher *"1/
Check Tires ......... V'
N_ Check Drive Wheets ***
Clean Lawn Mower ****
M'C}ean under Drive Cover'*"
OCheck Drive Belt /Pulleys ***
E_ Check Sharpen /Blade
Rap!ace
RLubrication
Clean and Recharge Battery *"
Check Engine Oil level " li_
l_ Change Engine Oil
Clean Air Fitter
tnspect Muffler
N Replace Spark Plug
EReplace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer
• (if so equ}pped)
•* Electric=Start mowers
•** Power-Propelled mowers
• *** Use a scraper
to clean under deck
i
1/
V', ii
EVE"Y BEFO.E
25 HOURS 100
ORSEASON HOURS iSTORAGE
,,I,/
V_,,,
V. ,, ,
=/3
I/
v' v_
_r a,
v_
v' v'
V'
I * Change more often if operating under a hea,,_' load or in high outdoor temperatures,
2-Service more often if operating in dirty or dust':/conditions.
3- Repiase blades more often when mow;ng in sandy soil
4 - Charge 48 hours at end of season,
5-And after each 5 hours of use.
GENERAL RECOMMENDATIONS
The warranty on this Iawn mower does not
cover items that have been subjected to
operatorabuse or negligence. To receive
fulI value from the warranty, operator must
maintain unit as instructedinthis manual.
LUBRICATION CHART
Wheel
adjuster (on
each wheeI)
Some adjustments wirl need to be made
periodicallyto property maintain your unit.
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual.
•At least once a year, replace the spark
plug, clean or replace air filter element
and check blade for wear. A new spark
plug and clean/new air filter element
assure proper air-fuel mixture and help
your engine run better and last longer.
•Follow the maintenance schedule inthis
manual.
BEFORE EACH USE
•Check engine oil level.
•Check for loosefasteners.
LUBRICATION
Keep unit well lubricated
(See "LUBRICATION CHART").
Engine oi{
(_ Mulcher
door hinge
(_ Rear door
hinge
(_) Handle bracket mounting pins
_Spray lubricant
See 'ENGINE" in Maintenance section,
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants wilt
attract dustand dirtthatwill shorten the life of
the self-lubricating bearings. Ifyou feelthey
mustbe lubricated, use onlyadry, powdered
0graphite type lubricant sparingly.
1

LAWN MOWER
Always observe safety rules when per-
forming any maintenance.
TIRES
•Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
BLADE CARE
For best results, mower blade must be kept
arp. Replace bent or damaged blades.
CAUTION: Use on[y a replacement
blade approved by the manufacturer of
your mower. Using a blade not approved
by the manufacturer of your mower is
hazardous, could damage your mower and
void your warranty.
TO REMOVE BLADE
1. Disconnect spark p|ug wire from spark
plug and place wire where it cannot
come in contact with plug.
2, Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt,
NOTE: Protect your hands with gloves
and/orwrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5, Remove blade and attaching hardware
(bolt,Iockwasherand hardened washer).
TO REPLACE BLADE
1. Position blade on the blade adapter
aligning the two (2) ho[es in the blade
with the raised lugs on the adapter.
2. Be sure the trailing edge of blade (oppo-
sitesharp edge) isup toward the engine.
3. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
4, Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
•The recommended tightening torque is
35-40 ft. Ibs.
Bladeadapter Crankshaft
Lockwasher '_
Blade \ u
bolt Hardened
washer Trailing' Crankshaft11
IMPORTANT: Blade bolt is heat treated.
If bolt needs replacing, replace only with
approved bolt shown in the Repair Parts
section of this manual.
TO SHARPEN BLADE
NOTE: We do not recommend sharp-
ening the blade - but if you do, be sure
the blade is balanced. An unbalanced
blade will cause eventual damage to lawn
mower or engine,
•The blade can be sharpened with a file
or on a grinding wheel, Do not attempt
to sharpen while on the mower.
• To check blade balance, drive a nail into
a beam or wall, Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail,
ff blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
GRASS CATCHER
•The grass catcher may be hosed with
water, but must be dry when used,
•Check your grass catcher often for dam-
age or deterioration, Through normal
use it will wear. Ifcatcher needs replac-
ing, replace only with approved replace-
ment catcher shown in the Repair Parts
section of this manual. Give the lawn
mower model number when ordering.
ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SJ-SL.
Select the oil's SAE viscosity grade according
to your expected operating temperature,
SAE VISCOSITY GRADES
I,
4 mm
/
•F-2o o_3_ 4 eo eo loo
3_MPERATURE I_NGE _'PECTEO BEFORE NEXT OILCHANGE
Change the oil after every 25 hours of
operationor at least once a year if the
lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use, Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to
drain oil, empty fuel tank by running en-
gine until fuel tank isempty.

1.Disconnectsparkplugwirefromspark
plugandplacewirewhereitcannot
comeincontactwithplug.
2. Removeengineoilcap;layasideona
cleansurface.
3. Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.
4. Wipe off any spilled oil from lawn
mower or side of engine.
5. Slowly pour oil down the oil fill spout,
stopping every few ounces to check the
oil level with the dipstick.
6. Stop adding oil when you reach the
FULL mark on the dipstick. Wait a
minute to allow oil to settle.
7, Continue adding small amounts of oil,
rechecking the dipstick until oil level
settles at FULL, DO NOT overfill, or
engine will smoke heavily from the muf-
fler on startup.
8. Always be sure to retighten oit dipstick
before starting engine.
9. Reconnect spark plug wire to plug,
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
AIR FILTER
Your engine will not run properlyand may
be damaged by using adirty air filter,
Replace the air filter every 100 hours of
operation or every season, whichever oc-
curs first. Service air cleaner more often
under dusty conditions.
TO CLEAN AIR FILTER
1. Remove cover.
2. Carefully remove cartridge.
3, Clean by gently tapping on a flat sur-
face. If very dirty, replace cartridge.
_CAUTION: Petroleum solvents, such as
kerosene, are not to be used to clean car-
tridge, They may cause deterioration of the
cartridge. Do not oil cartridge. Do not use
pressurized air to clean or dry cartridge.
4. Install cartridge, then replace cover. 12
Cartridge \ Slot
3over Backplate
IN-LINE FUEL FILTER
The fuel filter should be replaced once
each season. If fuel filter becomes
clogged, obstructing fuel flow to carbu-
retor, replacement is required.
I, With engine cool, remove filter and
plug fuel line sections.
2. Pface new fuelfilter in position infuelline
with arrow pointing towards carburetor.
3. Be sure there are no fuel line leaks
and clamps are properlypositioned.
4. Immediately wipeupanyspi!led gasoline.
SPARK PLUG
Replace spark plugat the beginningof
each mowingseason or after every 100
hoursofoperation,whicheveroccurs
first. Spark plugtype and gap setting
are shown in the "PRODUCT SPECIFIC-
ATIONS" section of this manual.
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-grass
and trash. Clean the underside ofyour
mower after each use.
_t_CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
• Clean the underside of your lawn
mower by scraping to remove build-up
of grass and trash.
• Clean engine often to keep trash from
accumulating, A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil,etc,
= We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result inshort-
ened engine life.

•1=WARNING: To avoid serious iniury, Mowing
before performing any service and A po,sition
adjustments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place wire where it cannot Hairpin
come in contact with plug. c°tter"--_
Mounting-'3
pin
LAWN MOWER
-TOADJUST CUTTING HEIGHT
See 'q'O ADJUST CU-I-FING HEIGHT" in
the Operation sectionof this manual.
-<4 Mowing __<_
I2oX. position / /
Itl
I/ /
i1 l
U4 oket f U4
LOW POSITION HIGHPOSITION
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibilitythatobjects wilt
be thrown out of the rear of the mower
into the operator mowing position, if the
deflectorbecomes damaged, it should be
replaced.
TO ADJUST HANDLE
The handle can be mountedin a high or
low position. The mounting holes in the
bottom of lowerhandle are off center for
raising or lowering the handle.
1. Remove upper handle and all wire
tie(s) securing cable(s) to lower handle.
2. Remove hairpin cotters from lower
handle bracket mounting pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4. Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
SQUEEZE
TO ADJUST
_owerhandle--"-- I
Mountingpin-----_l
Handle /_ U_I
bracket Hairpin otte, IJl! l
\
\
Lower
ROTATE
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attemptto increaseengine speed
or it may resultin personal injury. If you
believe that engine isrunningtoo fast or
tooslow, take yourmower to a qualified
service center for repairand adjustment.
CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate propedy due to
suspected carburetorproblems, take your
lawn mower to a qualified service center
for repair and/or adjustment.
iMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed. Overspeeding
the engine above the factory high speed
setting can be dangerous. Ifyou think
the engine-governed high speed needs
adjusting, contact aqualified service
center, which has proper equipment and
experience to make any necessary adjust-
ments.
13

Immediately prepare your lawn mower for Operator
storage at the end of the season or if the I
unit will not be used for 30 days or more. controlbar
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area
1 Clean entire fawn mower (See
"CLEANING" inthe Maintenance sec-
tion of this manual),
2 Lubricate as shown in the Maintenance
section of this manual.
3 Be sure that all nuts, bolts, screws, and
pins are securely fastened. Inspect
moving parts for damage, breakage
and wear Replace if necessary
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting
HANDLE
You can fold your lawn mower handle for
storage.
1, Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle bracket,
then move handle forward
2, Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back
IMPORTANT: When folding the handle for
storage or transportation, be sure to fold
the handle as shown or you may damage
the control cables
• When setting up your handle from the
storage position, the lower handle will au-
tomatically lock into the mowing position.
MOWING
POSITION
FOLD
FORWARD Upper
FOR handle
STORAGE
Handle
knob
Lower handle
ENGINE
FUEL SYSTEM
IMPORTANT: Itis important to prevent
gum depositsfrom forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage,
Alcohol blended fuels (called gasohol or
using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage.
• Empty the fuel tank by starting the en-
gine and letting it run until the fuel lines
and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage Add
stabilizer to gasoline in fuel tank or stor-
age container Always follow the mix ratio
found on stabilizer container Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the car-
buretor. Do not empty the gas tank and
carburetor if using fuel stabilizer.
14

ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
I. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder,
3. Pull starter handle slowly a few times to
distribute oil,
4. Replace with new spark plug.
OTHER
°Do not store gasoline from one season
to another.
•Replace your gasoline can if your can
startsto rust. Rust and/or dirt in your
gasoline will cause problems.
•If possible,store your unit indoors and
cover it to protect it from dust and dirt,
•Cover your unit with a suitable protec-
tive cover that does not retain moisture.
Do not use plastic. Plastic cannot
breathe, which allows condensation to
form and will cause your unit to rust,
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm.
D-CAUTION: Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing Inany enclosure.
TROUBLESHOOTING - See appropriate section in manual unless directed
to a qualified Sewice Center.
PROBLEM ...................CAUSE ........................... I,,,,,,,,,,CORRECTION ................
Does not start 1. Dirty air filter.
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter,
8. Control bar in released
position.
9. Control bar defective.
I0. Fuel valve lever (if so
equipped) in OFF position.
11.Weak battery (if equipped),
12.Disconnected battery
connector (if equipped).
Clean/replace air filter,
Fill fuel tank,
Empty rue! tank and refill tank
with fresh, clean gasoline.
Empty fuel tank and refill tank
with fresh, clean gasoline.
Connect wire to plug.
1.
2.
3.
4.
5,
6. Replace spark plug.
7. Tighten blade bolt or
replace blade adapter.
8. Depress controlbar to
handle.
9, Replace control bar.
10.Turn fuel valve lever
to the ON position.
11. Charge battery.
12. Connect battery to engine.
15

TROUBLESHOOTING. See appropriate section in manual unless directed
to a qualified Service Center.
PROBLEM CAUSE
Loss of power 1. Rear of lawn mower
Poor cut -
uneven
Excessive
vibration
Starter rope
hard to pull
Grass catcher
not filling
(It so equipped)
Hard to push
housing or cuttingblade
dragging in heavy grass.
2. Cutting too much grass.
3. Dirty air filter.
4. Buildup of grass, leaves,
and trash under mower.
5. Too much oil in engine.
6. Walking speed too fast.
1. Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildup of grass, leaves
and trash under mower.
1. Worn, bent or loose blade.
2. Bent engine crankshaft.
1. Engine flywheel brake is on
when control bar is released, i
2. Bent engine crankshaft.
3. Blade adapter broken.
4. Blade dragging in grass.
1. Cutting height too low.
2. Lift on blade worn off.
3. Catcher not venting air.
1. Grass is too high or wheel
height istoo low.
2. Rear of lawnmower
housing or cutting blade
dragging in grass.
3. Grass catcher too full.
4. Handle height position not
right for you.
CORRECTION'
1. Raise cutting height.
2. Raise cutting height.
3. Clean/replace air filter.
4. Clean underside ofmower
housing.
5. Check oil Jevel,
6. Cut at slower walking speed,
t. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height.
3. Clean underside of
mower housing.
1. Replace blade. Tighten
blade bolt.
2. Contact a qualified service
center.
1. Depress control bar to
upper handle before
pulling starter rope.
2. Contact aqualified service
center.
3. Replace blade adapter.
4. Move lawn mowerto cut
grass or to hard surface.
1. Raise cutting height.
2. Replace blade.
3. Clean grass catcher.
1. Raise cutting height.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher.
4. Adjust handle height to suit.
16

Reglas de Seguridad ................................ 17-19
Especificaciones del Producto ....................... 19
Montaje /Pre-Operaci6n ............................... 20
Operaci6n ................................................. 21-24
Programa de Mantenimiento ......................... 25
Mantenimiento .......................................... 25-27
Servicio y Adjustes ........................................ 28
Almacenamiento ....................................... 29-30
ldentificasi6n de problemas ...................... 30-31
Panes de repuesto .................................. 32-33
Garantfa ......................................................... 36
IMPORTANTE: Esta maquina cortadaora es
capaz de amputar las manos y los manos y
los pies y de lanzar objetos. Si no se observan
las instrucciones de seguridad siguientes se
pueden producir lesiones graves o la muerte.
_ll,Busque este s{mbolo qua sefiata las precau-
clones de seguridad de importancia. Quiere
deck- iiiATENCION!!! iIiESTE ALERTO!!!
SU SEGURIDAD ESTA COMPROMETIDA.
_IbADVERTENCIA: Siempre desconecte el
alambre de Is bu|[a y p6ngalo _)nde no pueda
entrar en contacto con la bujfa, para evitar el
arranque por accidente, durante la preparaci6n,
eI transporte, el ajuste o cuando se hagen
reparaciones.
_I_ADVERTENCIA: Los boreas, terminaies y
aocesorios relatives de ta bater[a contienen
plomoo compuestosde plomo, productos
quimicos conocidosen et Estado de California
comocausa de c_ncer y defectos al naeimiento
u otros dafios reproductivos.Lavar las manos
pu_s de mantpularlos.
RECAUCION: El tubo de escape del motor,
algunosde sue constituyentes y algunos com-
ponentes delvehiculo contienen o desprenden
productosquimicosoonocidosen e! Estado de
California comocause de c&ncery defectos al
nacimiento u otros dafios reproductivos.
4_PRECAUCI6N: El silenciador y otras piezas
del motor llegan aere extremadamente calien-
tee durante la operaci6n y siguen siendo cali-
entes despu_s de qua el motor haya parado,
Pare evitar quemaduras severas, permanezca
lejos de estas €_reas.
i, OPERACION
•Antes de empezar, debe familiarizarse
compJetamentecon Ice controlas y el uso
correcto de la maquina, Para esto, debe leer
y comprender todas las instrucciones qua
aparecen en la maquina yen los manualas
de operaci6n.
•No ponga las manos o los pies cerca o
debajo de las partes rotatorias. Mant_ngase
siempre lejos de la abertura de ladescarga.
• Permita qua solamente tas personas re-
sponsablas que est6n familiadzadas con las
instn.lccionesoperen la m&qulna.
•Despeje el &rea de objetos tales como pie-
dras, juguetes, alambres, huesos, palos, etc.
qua pueden eer recogldos y tanzados por las
cuchillas.
•AsegLirese qua eL_rea no se hallen per-
sonas, antes de segar, Pare la m_.quinasi
atguienentre en el ,_rea.
• No opera la maquina sin zapatos ocon
sandalias abiertas. P6ngase siemprezapatos
s61idos.
•No tire de la segadora haole atr_s a manes
que sea absolutamente necesario. Mire
siempre hacia abajo y hacie detr&s antes y
mientras qua se mueve hacia atr,_s.
• Nunca didgir et material descargado hacia
las personas. Evitar descargar material
contra paredes o barreras. El material puede
retornar al operador. Pare Ia cuchilJacuando
se pasa pot superficiesde grave.
° No opere la segadora sin los respectivos
resguardos, las places, el recogedor de
c6sped u circe aditamentos dlse ados pare
su protecci6n y seguridad.
°Refi6rase alas instrucciones del fabdcante
pare el funcionamiento e instalaci6n de
accesorios, Use _nicamente accesorios
aprobados por el fabric,ante.
• Detenga Ia cuchilta olas cuchiJtas cuando
cruce por calzadas, callas o caminos de
grava.
•Parer el motorcada vez qua se abandona el
aparato, antes de limpiar la segadora o de
remover residuos del tubo.
•Apagar el motor y esperar haste qua las
cuchillasast_n completamente parades
antes de remover el receptor de hierba.
° Sager solamente con luz del dfa o con una
buena luz artificial
• No opere lam_quina bajo la influenciadel
alcoho[ ode tas drogas,
17

• Nunca opere ]a maquina cuando la hierba
est_ mojada. Asegerese siempre de tener
buena tracci6n en sus pies; mantenga el
mango firmemente y camine; nunca corra.
- Desconectar el mecanismo de propulsion
aut6noma o el embrague de transmisi6n en
las segadoras que Iotienen antes de poner
en marcha el motor.
• Si el equipo empezara a vibrar de una
manera anormaI, pare el motor y revise de
inmediato para avedguar Ia causa. General-
mente la vibraci6n suele indicar que existe
alguna averfa.
° Siempre use gafas de seguridad o anteojos
con protecci6n lateral cuando opere la sega-
dora.
IL OPERACION SOBRE LAS CUESTAS
Los accidentes ocurren con m_s frecuencia en
las cuestas. Estos accidentes ocurren debido a
resbaladas o caidas, las cuales pueden resultar
en graves lesiones. Operar la recortadora en
cuestas requiere mayor concentraci6n. Si se
siente inseguro en una cuesta, no la recorte.
HACER:
• Puede recortar a trav_s de la supefficie de
Ia cuesta, nunca hacia arriba y hacia abajo.
Proceda con extrema precauci6n cuando
cambie de direcci6n en Ias cuestas.
• Renueva todos los objetos extrafios, tales
como guijarros, ramas, etc.
•Debe prestar atenci6n a hoyos, baches o
protuberancias. Recuerde que [a hierba a]ta
puede esconder obst&culos.
NO HACER:
•No recorte cerca de pendientes, zanjas o
terraplenes. El operador puede perder Ia
tracci6n en los pies oel equilibrio.
•No recorte cuestas demasiado inclinadas.
•No recorte en hierba mojada. 13 reducci6n
en ia tracci6n de la pisada puede causar
resbalones.
ill NI_IOS
Se pueden producir accidentes tr&gicos si el
operador no presta atenci6n ala presencia
de los nifios. A menudo, los nifios se sienten
atrafdos por ta maquina y pot ta actividad de
Ia siega. Nunca suponga que los nifios van a
permanecer en el mismo [ugar donde los rio
por L_ltimavez.
° Mantenga a los ni6os alejados de] Area de
Ia siega y bajo el cuidado estricto de otra
persona adulta responsable.
• Est_ alerta y apague la mAquina si hay nifios
que entran al Area.
• Antes y cuando este retrocediendo, mire
hacia atrAs y hacia abajo para verificar si hay
nifios pequefios.
° Nunca permita que los nifios operen la mA-
quina.
• Tenga un cuidado extra cuando se acerque
a esquinas donde no hay visibilidad, a los
arbustos, Arboles u otros objetos que pueden
interfedr con su Ifnea de visi6n.
IV. MANEJO SEGURO DE GASOLINA
Usar mucha atenci6n cuando se rnaneja gaso-
lina. La gasolina es extremamente inflamabley
los vapores son explosives.
•Apagar todos los cigarrillos, cigarros, pipas y
otras fuentes de ignici6n.
• Usar solo un contenedor apropiado.
• Nunca quitar el tap6n de la gasolina o aSadir
carburante con el motor en marcha. Esperar
que el motor se enfffe antes de repostar la
gasolina.
• Nunca repostar la maquina al intedor de un
local.
°Nunca guardar la m_,quina o el contenedor
de gasolina donde hay una llama abierta,
chispa o luz piloto como una catdera uotros
dispositivos.
• Nunca Ilenar contenedores en un vehfculo, en
un cami6n o caravana con unforro de pl&stico.
Colocar siempre los contenedoresen el sue]o
lejosde su veh[culo antes de Ilenar.
•Quitar equipos que funcionan con gasolina
del cami6n o caravana y repostar en el
suelo. Si esto no es posible, repostar dicho
equipo con un contenedor portati], mas bien
que con una tobera de gasolina.
•Mantener la tobera en contacto con el bordo
del dep6sito de carburante o de la apertura
del contenedor siempre hasta terminar el
abastecimiento. No usar un dispositivo de
cierre-apertura de la tobera.
° Si e[carburante cae en la ropa que se lleva,
cambiarsela inmediatamente.
• Nunea Ilenar en exceso el dep6sito de
carburante. Colocar el tap6n de la gasolina y
apretar de modo seguro.
V. SERVIClO
•Nunca haga funcionar una mdquina dentro
de un _rea cerrada.
• Nunca haga ajustes o reparaciones mientms
el motor est_ en marcha. Desconecte el
cable de la bujia, y mant_ngalo a cierta
distancia de 6sta para prevenir un arranque
accidental.
•Mantenga las tuercas y los pernos, espe-
cialmente los pernos del accesorio de la
cuchilla, apretados y mantenga el equipo en
buenas condiciones.
•Nunca manipule de forma indebidalos
dispositivos de seguridad. Controle regular-
mente su funcionamiento correcto.
° Mantenga Ia m_quina tibre de hierba, hojas
uotras acumulaciones de desperdicio.
Limpie los derrames de aceite o combustible.
Permita que la mAquina se enfrfe antes de
almacenaria.
° Pare einspeccione el equipo si le pega a un
objeto. Reparelo, si es necesario, antes de
hacerto arrancar.
° En ning_n caso hay que regular ta altura de
las ruedas mientras el motor estA en marcha.
18

Los componentes del receptor de lahierba
van sujetos a desgaste, daSos y deterioro,
que pueden exponer tas partes en mov-
imiento o permitir qua objetos seen dispara+
dos. Controlar frecuentemente y cuando sea
necesario sustituir con partes aconsejadas
por el fabdcante+
• Las cuchillas de la segadora est&n afiladas
y pueden cortar. Cubdr las hojas o Ilevar
guantes, y utilizer precauciones especiales
cuando se efect_a mantenimiento sobre las
mismas+
• No cambie eJajuste (tel regulador del motor
ni exceda su veJocidad.
. Mantener o sustftuir las etiquetas de
seguridad e instrucciones, cuando sea
necesario+
_ADVERTENCIA: Este segadora viene equipado con un motor de combusti6n interne yno se
debe usar sobre, o cerca, de un terreno no desarrollado cubierto de bosques, de arbustos o de
cesped, omenos que el sistema de escape del motorvenga equipado con un amortiguador de
chispas que cumpla con las leyes locales oestatales (si existen)+ Si se usa un amorliguador de
chispas, el operador debe mantenedo en condicionesde trabajo eficientes_.
En el estado de California, la tey exige Io anterior(SecciSn 4442 del "California Pub]ic Re-
sources Code"). Otros estados pueden contarcon otras leyes parecidas+ Lasteyes federales
se apiican en la tierras federales.
NDmero de Sede:
Fecha de Compra:
Capacidad y Tipo de Gasoline: 1.5 Cuartos (Regular sin Plomo)
Tipo de Aceite (API SG-SL): SAE 30 (Sobre 32°F); SAE 10W-30 (Debajo 32°F)
Capacidad de Aceite: 20 Onzas
Bujfa (Abertura: .030") Champion 8815
TorsiSn del Perno de la CuchilJa: 35-40 ft, Ibs.
El ndmero del nodelo y el de serie se encuentran en la calcomania adjuntaala parte trasera
de la+eajade la segadora. Debe registrar tanto el nemero de serie come la fecha de compra y
mantengalos en un lugar seguro pare refencia an el futuro.
19

Lea estas instrucciones y este manual comple-
tamente antes de tratar de montar u operar su
segadora nueva.
IMPORTANTE: Este cortac_sped viene SIN
ACEITE O GASOLINA en el motor.
Su segadora nueva ha sido montada en la
f,_brica con la excepci6n de aquellas partes que
se dejaron sin montar por razones de env{o.
Todas Ias partes como las tuercas, las arande-
las, los pernos, etc., que son necesadas para
completar el montaje ban sido co[ocadas en Ia
bolsa de partes. Para asegurarse que su sega-
dora funcione en forma segura y adecuada,
todas las partes y los art_culos de ferreter{a que
se monten tienen que ser apretados segura-
mente. Use Ias herramientas correctas, come
sea necesario, para asegurar que se apdeten
adecuadamente.
PARA REMOVER LA SEGADORA DE
LA CAJA DE CARTON
1. Remueva las partes sueltas que se incJuyen
con la segadora.
2. Corte las dos esquinas de los extremos
de ta caja de cart6n y genda ef panel del
extremo piano.
3, Remueva todo el matedal de empaque, e×-
cepto Ia curia entre el mango superior y _1
inferior, y lacuria que sujeta la barra de los
control que exige Ia presencia del operador
junto con el mango superior.
4. Haga rodar la segadora hacia afuera de la
caja de cart6n y revfsela cuidadosamente
para verificar si todav{a quedan partes
sueltas adicionales.
COMO PREPARAR SU SEGADORA
PARA DESDOBLAR EL MANGO
IMPORTANTE: Despliegue e{mango con
mucho cuidado para no pellizcar o dafiar los
cables de control.
t. Levante los mangos hasta que la secci6n
del mange inferior se asegure en su lugar,
en la posici6n para segar.
2. Remueva la curia protectora, levante la sec-
ci6n del mango superior hasta su lugar en
el mango inferior, y apriete ambas manillas
det mango.
3. Remueva la cuSa del mango que sujeta ta
barra de los control que exige la presencia
del operador junto con el mango supedor.
El mango de la segadora puede ajustarse
seg_n le acomode para segar. Refi_rase a
"AJUSTE DEL MANGO" en Iasecci6n de
Servicio y Ajustes de este manual.
POSICION
que s×ige la PARA
presencia deI SEGAR
operador
,//
LEVANTAR Mango
superior
ManilIa deI
mango
Mango Inferior
PARA MONTAR ELRECOGEDOR DECF_SPED
1. Ponga el bastidor dei recogedorde cdsped
en la bolsa del c6sped con la parte dgida
de Tabolsa en la parte inferior, AsegLirese
que el mango del bastidor est_ en el exte-
rior de Iaparte superior de la bolsa.
2. Deslice los sujetadores de vinito sobre el
bastidor.
AVISO: Si los sujetadores de vinilo est_n muy
duros, m6talos en agua catiente por aIgunos
minutos. Si se moja la bolsa, d6jela que se
seque antes de usarla,
de vinilo deI bastidor
PARA INSTALAR LOS ACCESORIOS
Su segadera rue enviada Iista para usarse
como una acolchadora de capa vegetal. Para
convertir la de modo que pueda ensacar o
descargar, refi_rase a "PARA CONVERTIR LA
SEGADORA" en Ia secci6n de Operaci6n de
este manual.
2O