Aristel AN-P28 User manual

4G LTE AN-P28
Quick Installation Guide

Overview

Indicators
Type Status Description
On RSSI signal strength
Off No signal
Red 4G/LTE disconnected or SIM is not ready
Blue 4G/LTE connected
Blue WPS function open
Flicker WPS client connecting
Off WPS function closed
Blue Wi-Fi open

Off Wi-Fi off.
Blue In use
Off Idle
BATTERY
Blue Battery normal
Yellow Low battery
Off No battery
ADAPTER
Blue AC adapter connected
Off AC adapter disconnected
Blue Power on
Off Power off

Interface
Interface Description
1. Phone Port Connect to telephone or alarm system.
2. Battery Interface Slide off the cover and install the battery, then close the cover.
3. LAN Port Connect to PC/laptop through Ethernet cable.
4. USB Only for firmware upgrading.
5. DC Power Connect to AC adapter.

6. SIM Slot Slide off the SIM slot cover and install the SIM, then close the cover.
7. External ANT
Interface Slide off the cover and install the external antenna.
8. Power Switch Press this button to power on or off the AN-P28.
9. WPS Button Press this button to wait for WPS connection from WPS client.
10. Reset Button Press and hold for about 3-4 seconds to restore the default settings.
11. WLAN Switch Press this button to switch on or off Wi-Fi.

Installation
1. Hardware Installation
•Installing the SIM card.
•If the signal is poor when using built-in antenna, install an externalantenna
•If required, connect telephone/alarm system to phone port through RJ11cable.
•Installing the battery.
•Connecting the AC adapter to DC powerinterface.
•Press the power switch to power on theAN-P28.

2. Setting up an Ethernet Connection
Connect your PC, laptop, or SIP server to LAN port through Ethernet cable for
wired internet access. For multiple SIP lines use a SIM with static IP address.
Note. Ensure that the network connection on your PC or laptop is configured as
Obtain IP address and DNS server address automatically.
3. Setting up a Wi-Fi Connection
Method 1: Setting up a Wi-Fi connection manually
Select the SSID of P28 on computer or mobile phone and click Connect. After
inputting password, the Wi-Fi can be used (default SSID and Key can be
accessed as shown below). Please access the Web GUI and select the following
1- WLAN Configure > Basic settings

2- Press Edit to see the Wi-Fi Key as shown below.
Method 2: Setting up a Wi-Fi connection through WPS
If the device supports WPS, you can set up a WPS connection as follows:
1. Ensure that Wi-Fi is switch on and WPS function isenabled.
2. Press the WPS button, and then WPS indicator will startsblinking.
3. Activate the WPS connection on the device in 30 seconds. Your device
will notify you when it is connected

Web-based Configuration
1.Accessing the Configuration Page
Make sure the connection between your device and the client is active. Launch the
Internet browser and enter http://192.168.0.1.The user name is admin and password
is admin. For logging into the WEB Configuration Page,
proposed browsers are as follows :

●at least IE 7.0 ● at least Firefox 3.0
●at least Safari 4.0 ● at least Opera 10.0
●at least Chrome 10.0
2. Settings
Changing SSID and Wi-Fi Key
1. Select WLAN Configure > Basic Settings
2. Press Edit to enter SSID setting menu.
3. Edit the parameters you want to change, press Submit.

WPS Settings
1. Select WLAN Configure >WPS Settings
2. Select Enable(Enabled by default)
3. Press Apply
Static IP
1. Select Route Function > Static IP
2. Press Add Entry, and input the MAC and IP you want tobind.
3. Press Save
Firewall Settings
1. Enter Firewall Settings
2. Select the firewall function you want to set.
Hotline settings
1. Select Phone Settings > Hotline settings
2. Edit the hotline number
3. Press Save

Warnings and notice
Do not insert or remove the SIM card when the device ispowered up.
Please power offthe device ifitisnot going tobe used for anextended
period of time.
Use the original power adapter andbattery, oraccessories that are authorized,
otherwise it may damage the device and may bedangerous.
Keep the device in a well-ventilated andcool area and away from direct
sunlight or any heat sources asitmay cause fire, explosion due to overheating
of the battery.
To get the best performance from the device keep itaway from electronic
appliances that generates strong magnetic or electric fields such as microwave
ovens and refrigerators.
Do not dismantle thedevice and it's accessories as this voids the warranty of
the device.
The device isfor indoor useonly. Do not useitoutdoors.
SIM card with Static IP required
www.aristel.com.au E.&O.E.