Arkuz BlueNet User manual

Arkuz BlueNet Switch
Device Installation Guide

Contents
Arkuz BlueNet Device
Product Contents.
Typical Switchboard Panel
Connections
Connecting Arkuz BlueNet
Switch to your Switchboard
Panel
Your Switchboard
connections when powered
by Arkuz BlueNet Switch

Arkuz BlueNet Switch
Product Content
Arkuz Power Supply Module.
The power supply module has 2 sets of wire
coming out of it. The set of 2 wires with RED
colour is Input to the power supply module. The
set of 2 Yellow wires is output of the power supply.
Arkuz BlueNet Switch Module.
The BlueNet Switch has 3 sets of wires coming
out of it.
Set 1: Black & Red Wire with a knot are
INPUT to power up the BlueNet Switch.
Set 2: 5 thin multi-coloured wires are INPUT
to BlueNet Switch to signal an operation on
the wall switch on the switchboard.
Set 3: 5 thick multi-coloured wires. BLACK
wire is Phase INPUT and the other 4 multi-!
coloured are Phase OUTPUT for each load.

Typical Switchboard Panel Connections
MAINS & NEUTRAL
220 Volt AC lines.
Switches connect
Input Current to
various Loads.
Fan uses Regulator
for speed control.
Switchboard Panel
Loads
220VAC
Socket
Switches
Regulator

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Items Required
Arkuz BlueNet Switch
Screw Driver
Electric Wire
Duct Tape

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 1
Make sure all power
to the the switch-
board panel is turned
to OFF position.
The installation deals with High Voltage AC
current hence take at most caution while
installing the Arkuz BlueNet Switch. It is highly
recommended that any electricity coming to the
switchboard panel where the smart light
controller is being installed is switched off before
starting the installation and be turned back on
only after the installation is complete.
Switchboard Panel
Loads
220VAC
Socket
Switches
Regulator

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 2
Disconnect Input &
Output Connections
to all of the
switches.
Disconnect and
remove the Fan
Regulator.
Switchboard Panel
Loads
220VAC
Socket
Switches

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 3
Connect the RED
set of wires of Arkuz
Power Supply with
the 220VAC wires.
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 4
Connect the
YELLOW set of
wires to the pair of
RED/BLACK wire
set of Arkuz
BlueNet Switch
module.
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 5
Connect the MAINS
wire of the 220 Volt
AC wires to the
THICK BLACK
wire on the TOP
RIGHT of the Arkuz
BlueNet Switch.
BlueNet Switch
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 6
Connect the THIN set of
wire on the left left of the
Arkuz BlueNet Switch as
follows.
Connect the TOP THICK
BLACK wire to one end
of every switch.
Connect each of the 4
coloured wire to the other
end of switch saperately.
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 7
Connect the 4THICK
Multi Coloured wire on
the RIGHT of the Arkuz
BlueNet Switch to different
loads.
Make sure that the
connection colour
corresponds to the thin set
of multi colour wire
connected to the switches.
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Connecting Arkuz BlueNet Switch
to your Switchboard Panel
Step 8
Installation is
complete.
Turn the power on the
switchboard panel.
Operate the switches.
They should turn the
same way as before.
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Your Switchboard connections when
powered by Arkuz BlueNet Switch
Switchboard Panel
Loads
220VAC
Socket
Switches
Power
Supply
BlueNet Switch

Arkuz Technologies
beyond possibilities