Armitron IW-YP12585-2 User manual

IW-YP12585-2
INSTRUCTIONS MANUAL
FEATURES
SELECTING FEATURES
SETTING THE TIME AND CALENDAR
STOPWATCH
SPLIT TIME
• Time Telling Mode (Hours, Minutes, Seconds, Date and Day of the
Week)
• 24 Hour Alarms
• Hourly Chime
• Calendar Mode
• Chronograph Mode: Hours, Minutes, Seconds, and 1/100 of a sec-
ond with Lap Operation
• Water Resistant as indicated on the watch
• INSTALITE - Electro Luminescent Display
NOTE: Please note that your watch may have a different outlook on the
display than this diagram. However, the functions and operation are the
same as these instructions.
1. Time Telling Mode displays Hours, Minutes, Seconds, and Day of the
Week.
2. From Time Telling Mode, press ‘B’ once. Chronograph Mode appears.
Press ‘B’ three times to return to Time Telling Mode.
3. From Time Telling Mode, press ‘B’ twice. Alarm Mode appears. Press ‘B’
twice to return to Time Telling Mode.
4. From Time Telling Mode, press ‘B’ three times. Time Setting Mode ap-
pears. Press ‘B’ once to return to Time Telling Mode.
5. From Time Telling Mode, press and hold ‘C’ to enter Calendar Mode.
The Month, Date, and Day of the Week appear. Release ‘C’ to return to
Time Telling Mode.
1. From Time Telling Mode, press ‘B’ three times. Seconds flash. Press ‘C’
to zero out the Seconds.
2. Press ‘A’. Minutes flash. Press ‘C’ to advance the Minutes.
3. Press ‘A’. Hours flash. Press ‘C’ to advance the Hour.
NOTE: Pressing and holding ‘C’ will advance digits rapidly. When 12 Hour
Format is selected, ‘A’ indicates ‘a.m.’ times; ‘P’ indicates ‘p.m.’ times.
4. Press ‘A’. The Date flashes. Press ‘C’ to advance the Date.
5. Press ‘A’. The Month flashes. Press ‘C’ to advance the Month.
6. Press ‘A’. The Day of the Week flashes. Press ‘C’ to advance the Day of
the Week.
7. Press ‘B’ to end set sequence and return to Time Telling Mode.
1. From Time Telling Mode, press ‘B’ once to enter the Stopwatch Mode.
2. Press ‘C’ to start timing.
3. Press ‘C’ again to stop timing.
4. Press ‘A’ to reset to zero.
5. Press ‘B’ to return to Time Telling Mode.
1. While in the Stopwatch Mode, press ‘C’ to start timing.
2. Press ‘A’ to measure and display Split Times.
3. Press ‘C’ to stop timing at the end of the event.
4. Press ‘A’ to reveal the final Split Time.
5. Press ‘A’ to reset to zero.
5. Press ‘B’ to return to Time Telling Mode.
SETTING THE 24 HOUR ALARMS
1. From Time Telling Mode, press ‘B’ twice to enter the Alarm Mode. Alarm
Hours flash.
2. Press ‘C’ to advance the Alarm Hour.
NOTE: Pressing and holding ‘C’ will advance digits rapidly.
3. Press ‘A’. Alarm Minutes flash. Press ‘C’ to advance the Alarm Minute.
4. Press ‘B’ to end set sequence and return to Time Telling Mode.
ACTIVATING ALARM + HOURLY CHIME
EL LIGHT FEATURE
1. From Time Telling Mode, press and hold ‘A’ and press ‘C’ once. The
Alarm Symbol appears to indicate that the Alarm is activated and will
sound at the preset Alarm Time for about 60 seconds or until ‘A’ is pressed.
2. Press and hold ‘A’ and press ‘C’ once again to deactivate the Alarm.
3. From Time Telling Mode, press and hold ‘A’ and press ‘B’ once. All of the
Days of the Week appear to indicate that the Hourly Chime is activated and
will sound every hour on the hour.
4. Press and hold ‘A’ and press ‘B’ once again to deactivate the Hourly
Chime.
SNOOZE: Press ‘D’ to stop the Alarm for 5 minutes. The Alarm sound will
resume after 5 minutes. Press ‘D’ again to stop the Alarm for another 5
minutes.
5. Press ‘A’ and ‘C’ again to deactivate the Alarm.
1. Press ‘D’ in any mode to illuminate the watch face. The backlight will
remain lit for 3 seconds.
NOTE: EXCESSIVE USE OF LIGHT WILL SHORTEN BATTERY LIFE.

WATER RESISTANCE
RETURN YOUR WATCH FOR SERVICING
USE OUR NATIONWIDE SERVICE CENTERS. YOU
CANNOT RETURN WATCH FOR SERVICE WHERE
IT WAS PURCHASED.
This is a WATER RESISTANT watch. Do not operate push buttons below
the surface of the water. Should water or condensation appear in the
watch, immediately have the watch checked. Water can corrode electron-
ic parts inside the case. Please call [phone] for a listing of all approved and authorized
service centers and locations, or visit our website at:
WWW.ARMITRON.COM
YOUR WATCH SHOULD NOT BE RETURNED TO THE PLACE OF
PURCHASE. Carefully pack your watch in a sturdy box (do not send in a
gift box for same will not be returned) and mail to the nearest approved
authorized service station. Because of possible loss, we recommend that
you insure the watch, return receipt requested, when using the mail. If you
do not receive a receipt within a reasonable time, start a tracer through
the originating post office. Never include a special watch band or any
other article of personal value in your shipment.
If your watch requires cleaning, lubrication, battery changing, or needs
a crystal replaced, Armitron Adventure approved Service Centers are
available in your area. These repair facilities use Armitron Adventure parts
and components to assure quality and future performance. Free estimates
are available in advance, should you need servicing or repairs not covered
under the warranty. Repairs covered under the warranty may require proof
of purchase, so retain the purchase receipt.
CHANGING THE BATTERY
Change the battery when the watch becomes slow, the readout darkens or
does not appear, or the backlight fails. Before removing the old battery, be
sure to denote its polarity so that the new battery is installed in exactly the
same way. Replace with the same kind or equivalent only. This watch
contains precise electronic components and should only be opened by
a qualified watch technician. However, it is not necessary to return your
watch to the manufacturer for battery replacement. It is recommended that
you bring your timepiece to a local jeweler.
IW-YP12585-2
INSTRUCTIONS MANUAL