Armorgard forma-stor FR100-T User manual

User manual for your
Armorgard Forma-Stor
forma-stor™
Model Numbers FR100-T - FR400-T

2
Welcome...
to your Armorgard Forma-Stor, the most secure solution
for portable and fast-assembly storage. The Forma-Stor
can be erected in minutes from flat pack panels, making
it, simple, safe, and secure!
Please read this user manual carefully
prior to setting up the Forma-Stor
Please call 023 9238 0280 if you have any questions on setting up your
Forma-Stor.
Contents
Welcome
Safety Information
Contents
Erecting the Forma-Stor
Breaking up the Forma-Stor
Using the lifting eyes
Additional kits
General Information
................................................................................. page 2
.................................................................... page 3
.................................................................................. page 4
........................................................... page 5
..................................................... page 8
................................................................ page 9
........................................................................ page 10
................................................................ page 10

3
Safety Information
At least 2 people are required to safely erect or take down the
Forma-Stor and all relevant PPE must be worn while doing so.
The Forma-Stor must be positioned on a flat, solid surface, and
should be level and stable before being used.
Ensure the Forma-Stor is fully constructed and that it is empty
before lifting or moving it. Only qualified personnel should lift the
Forma-Stor.
Technical Specification
Product code Net weight
FR100-T 255kg
FR200-T 385kg
FR300-T 470kg
FR400-T 595kg

4
Contents
FR100-T pack contents:
2x 1m side panels
1x 2m rear panel
1x 2m door panel
1x 1x2m base
1x 1x2m roof
8x M12 x 20mm bolts
8x M12 x 50mm bolts
8x M12 large washer
8x M12 small washer
8x Pipe linchpin
4x M12 lifting eye with rubber
washer
FR300-T pack contents:
2x 3m side panels
1x 2m rear panel
1x 2m door panel
1x 2x3m base
1x 2x3m roof
8x M12 x 20mm bolts
8x M12 x 50mm bolts
8x M12 large washer
8x M12 small washer
8x Pipe linchpin
4x M12 lifting eye with rubber
washer
FR400-T pack contents:
2x 4m side panels
1x 2m rear panel
1x 2m door panel
1x 2x4m base
1x 2x4m roof
10x M12 x 20mm bolts
8x M12 x 50mm bolts
8x M12 large washer
10x M12 small washer
8x Pipe linchpin
4x M12 lifting eye with rubber
washer
FR200-T pack contents:
2x 2m side panels
1x 2m rear panel
1x 2m door panel
1x 2x2m base
1x 2x2m roof
8x M12 x 20mm bolts
8x M12 x 50mm bolts
8x M12 large washer
8x M12 small washer
8x Pipe linchpin
4x M12 lifting eye with rubber
washer

5
To begin assembling the
Forma-Stor, place the base on a
level, stable surface.
Bolt in the 20mm bolts into each
corner of the base, two to every
corner.
Place one of the side panels on
the base, using the bolts in step 2
to locate the panel.
Ensure it is supported safely
while the 45mm bolts are fixed in,
securing the side to the base.
1. 2.
3. 4.
Erecting the Forma-Stor

6
Put a pipe linchpin through the
rear panel and side panel to hold
them together.
6.
7. 8.
There are two linchpins for each
corner.
Place the other side panel on the
base, and secure it with bolts as
described in step 3.
5.
Place the rear panel next to form a
corner which will support the side
panel.

7
9.
Secure the corner with two more
linchpins.
10.
11. 12.
The door panel is the last panel
to be fixed on. This slots onto
the base and is fixed to the side
panels with linchpins as described
in step 5.
Ensure the grooves in the roof fits
in the top of the 4 panels all the
way around.
WARNING! The roof is heavy and care should be taken
when lifting into position. Please take all safety precautions
necessary when moving this part.
Now place the roof on top. An
extra person may be needed
inside the unit to balance the roof.

8
The Forma-Stor is now ready for
use
To break up the Forma-Stor,
remove the parts in the reverse
order to that which they were
assembled.
The roof is removed first, followed
by the door panel, a side panel,
the rear panel and the remaining
side panel. Fixings can be
screwed back into the panel
afterward for safekeeping.
1. 2.
Breaking up the Forma-Stor
14.
13.
Lastly, fix the roof in place using
the bolts provided.

9
Before lifting, ensure that the bolts
holding the lifting eyes are securely
in place.
Attach the lifting equipment to all
four lifting eyes and ensure that
the load is lifted evenly across all
four eyes.
1. 2.
Using the lifting eyes
WARNING! The lifting eyes are provided only for positioning
the Forma-Stor, and the unit must be empty while lifting.
Before lifting, each lifting eye needs to be checked that it is
fitted correctly, and should be inspected by a lifting operator
before use.