Armorgard siteboss cabinet SB48 Quick start guide

siteboss cabinet
TM
Operational and maintenance manual
Suitable for: SB48
1-877-794-2848 [email protected]

2
Welcome
Welcome to your Armorgard SiteBoss Cabinet. Pioneering
jobsite security and usability, this cabinet is built to
last and built to protect. Please consult this manual for
instructions on how to get the most from the unit.
Please read this operational and maintenance manual
carefully prior to setting up the SiteBoss Cabinet.
Always keep this manual with the product and read
prior to use.

3
Contents
Safety information 4
Product specification 5
What’s included 6
Tools you’ll need 7
Getting to know your SiteBoss Cabinet 8
Padlock housing dimensions 9
How to use 10
Installing the padlock 11
Installing the rubber grommet 12
Electrical safety information 13
How to use the lock 14
Optional extras 15
Installing the casters 16
Attaching the crane lifting eye kit 17
Storing the unit 18
Transporting the unit 19
Equipment care & ongoing maintenance 20
Warranty 21
Spare parts 23

4
Safety information
Before using a SiteBoss Cabinet, ensure any relevant risk assessments are carried out.
Armorgard cannot be responsible for accidents that occur due to negligence.
Ensure that the SiteBoss Cabinet is not damaged before using it.
Always lock the unit and the casters when not in use or out of sight. Do NOT leave keys
inside the unit while locking.
Do not put hands, arms or legs near the unit opening while closing the doors.
Improper dangerous activities performed using the SiteBoss Cabinet increases the risk
of personal injury, please follow the stated instructions to prevent incidents.
Ensure weight is evenly distributed and that heavier items are ALWAYS loaded in the
base.
 Whencastersareunlocked,theunitmustalwaysbepositionedonaat,levelsurface.
Ensure casters are locked when the cabinet is not being moved.
You must close doors before putting the cabinet in motion, for stability and to prevent
content and product damage.
 Ifcastersarebeinginstalled,thesemustbeinstalledaccordingtoourspecicationand
shouldbecheckedregularlytoensuretheyarestilltforpurpose.
This product should not be used for transporting or storing explosives, hazardous
wastes,ammablesorhazardousmaterialssuchasgastanks,containersofsolvents,
dynamite, gunpowder, etc.
Any alteration to or unintended use of this product could create a danger of an explosion
or other hazardous conditions that can result in serious personal injury, property damage
or even death.
Only position the SiteBoss on stable and even ground to prevent it rolling over and
causing injury or personal harm.
Do not exceed shelf capacity of 300 lbs.

5
Do Don’t
Lock the unit when leaving it unattended Leave keys inside unit when locking
Keep opening clear when closing doors Ever let cabinet become unstable
Integrity check the unit before lifting Use unit to store hazardous substances
Fully unload before lifting Leave casters unlocked when in position
Product specification
Product
code
Description Weight
(lbs)
External Dimensions
W x D x H (inches)
Internal Dimensions
W x D x H (inches)
SB48 Site Cabinet 517 60.2 x 24.6 x 60.6 59.8 x 20.9 x 56.9
While every effort has been made to ensure this operational and maintenance manual
covers every aspect needed to operate your product safely, please take care when using
the product and always operate with caution. Always liaise with management personnel
on site for any additional operational restrictions that you need to be aware of.
SiteBoss™ Patent 2211899.6
Only use UL or CSA listed electrical devices that meet the requirements of the local
jurisdiction
Always wear the appropriate PPE for the task you are performing, as outlined in your risk
assessment or safe work practices.
The unit has an overall WLL of 2200 lbs.

6
What’s included...
1x SiteBoss Cabinet 1x rubber grommet
3x shelves
1xUltraLockxingkit
(padlock not included)

7
Tools you’ll need...
One person
required
Rubber mallet
or hammer (for
adding rubber
grommet)
Adjustable
wrench or ratchet
and socket
(11/16” socket for
installing padlock
and 1/2” socket
for casters)

8
Getting to know your SiteBoss CabinetTM
Pioneering jobsite security and usability, this
cabinet is built to last and built to protect
Stainless steel
padlock locking
mechanism
Recessed
handles
Data plate which
lists each unique
product serial
number
4-way forklift pockets
Cable pass-
through point
Adjustable
shelf
Forklift skids Suitable for
use on-site
Product with
handles
Casters (optional extra)
Pull
latch
UltraLock

9
Padlock housing dimensions
Padlock not included
This lock system is designed to be used with a Master Lock No. 1, Master Lock No. 5, ABUS
41/50 or American Lock No. 50, or an equivalent sized lock. If you are using a padlock not
listed above, it is your responsibility to make sure the lock mechanism is working correctly.
Padlocks must meet ALL requirements listed in diagram.

10
How to use
1. 2.
3.
The SiteBoss Cabinet units arrive
assembled. The upper shelves have
xedlocationsandthelowershelf
can be installed in either of two
positions.
It is important to check that the
product is not damaged upon arrival
and all parts are intact.
You may require a forklift or pallet
truck when unloading your Site-
Boss Cabinet.
4. To adjust the shelves, tilt them at an
angle and pivot off the brackets.

11
Installing the padlock
1. 2.
3.
Totthepadlock,locatethecavity
where it will be installed.
Inside the product, on the back of
the cavity (between both doors)
there will be a bolt with a nut. Re-
move nut and bolt to allow access
for the padlock.
Insert the shackle of the padlock
inside the cavity horizontally. The
keyhole should remain accessible
from the front face.
4. Once the padlock is inserted, return
the bolt into its original place, and
use the nut to secure it all together.
Always check that the lock is in
correct working order after installing,
before the door is closed.
Video: how to install
the padlock

12
Installing the rubber grommet
1. 2.
3.
There are two cut-out plates in
the unit. Decide which is the most
suitable for the intended use. Once
located, using a rubber mallet,
carefully knock the cut-out plate
from the inside.
Next, take the rubber grommet
andplaceitfromtheoutsidetot
the cut-out. Ensure it is properly
installed and no sharp edges are
exposed.
When passing cords through the
grommet, insert them from the
outside.
4. After inserting, pull 2-3” of the cord
backtomakesurerubbernsare
pointing out the box.
Video: how to install
the rubber grommet

13
Electrical safety information
All electrical work MUST be performed properly with safety precautions. To prevent
injury or damage to property, please ensure the below information is read carefully.
Only use UL or CSA listed electrical devices that meet the requirements of the local
jurisdiction.
Extension cords
Ensure that manufacturer’s instructions and safety information are always followed.
Never use a damaged cord. Always check before using.
Always insert cords after the rubber grommet is safely in place.
You must not overload the extension cord.
You must only use cords that are designed for outdoor use.
Prior to transporting the unit, ensure all cords have been removed from the grommet.
Extension cords must not be connected to outlet that also supplies critical safety
equipment.
 AlwaysuseULcertiedproducts/accessories.
Cordless battery chargers
Ensure that manufacturer’s instructions and safety information are always followed.
Chargers and batteries must be cared for properly following manufacturer’s guidelines.
Place electrical components on shelf (if applicable).
 Ifelectricalcomponentsbecomewetorexposedtohazardousandammable
substances, switch off and discontinue use immediately.
Always check chargers and batteries will operate properly and are not damaged.
Do NOT come into contact with metal prongs when plugging or unplugging electrical
components.
 Electricalcomponentsmustbekeptawayfromammableandhazardoussubstances.
Only place suitable jobsite equipment in the unit.

14
How to use the lock
1. Once the padlock is installed, to un-
lock the unit, you will need to insert
the key into the padlock. Twist it as
normal, and this will unlock the door.
3. To lock your product, you must
close the doors and simply push the
padlock in. Always double check
that the locks are properly secured
before leaving unattended.
2. Push down on the pull latch to
release and open the door.

15
Take your SiteBoss
CabinetTM to the next
level with these
optional extras
Contact the Armorgard team to find
out more about the optional extras
for your product.
Casters
To make your SiteBoss
Cabinet mobile
Crane lifting eyes
To transport by crane

16
Attaching the casters
(optional extra)
2.
4. Repeat step three for the other cast-
ers. Once complete, check all nuts
are tight, and then ensure the casters
can swivel 360° before lowering the
SiteBoss Cabinet.
3.
Armorgard caster kits come with two
swivel casters and two swivel-braked
casters. We recommend attaching
the braked casters on the same side.
1. For the SiteBoss Cabinets that
can be installed with casters, lift
the unit on to a stable platform to
ensure it does not roll and cause
injury. The unit MUST be empty
when installing casters.
Insert the caster plate and tighten
the nuts from the bottom using
the adjustable wrench.
Video: how to attach
the casters

17
Attaching the crane lifting eye kit
(optional extra)
1. 2.
For the SiteBoss Cabinets that can
be attached with crane lifting eyes,
use a 13/32” metal drill bit to drill out
the four pilot holes located on each
side of your SiteBoss Cabinet.
Thread the coach bolts through the
lifting eyes, then back through the
unit. Inside the unit, add a
backing plate, washers and nylocks
to each bolt as shown.
Before lifting, a risk assessment must be performed by a qualified person to ensure the
product is safe to lift.
3. Always check the working load limit
of the product before carrying out
a lift.
Video: how to attach
the crane lifting eyes

18
Storing the unit
1. 2.
3.
Theatsidesandrecessedhandles
of the SiteBoss Cabinet can help
save space when storing the unit.
Ensure that the lock is secured when
leaving the SiteBoss Cabinet unat-
tended. This is essential to maintain
the maximum security of the unit.
When the SiteBoss Cabinet is
in position, always ensure the
caster brakes are used.

19
2. When transporting, ensure the unit
is secured using straps or other
necessary measures.
Transporting the unit
The design of the SiteBoss Cabinet makes transporting the product easy.
The units come with forklift pockets for transporting using a forklift or pallet truck. Optional
casters and crane lifting eyes can be installed to these units using the pre-drilled holes.
Please note that units are heavy may require assistance to lift, and it is always advised to lift
the units when they are empty of contents.
1. Always secure the lock and remove
key before lifting the unit, to
ensure that the lid does not open
unexpectedly. Do not leave the key
inside the padlock.

20
Equipment care
TheSiteBossCabinetisweatherresistantandnishedwithadurablepowdercoating,soit
is suitable for outdoor use, however, it does not mean it is waterproof. It is always important
to note that any electrical components or equipment susceptible to water damage should be
sealed.
Always ensure that the product data plate remains visible and in good condition, especially
the unique serial number.
Ongoing maintenance
It is important to check that the SiteBoss Cabinet is not damaged before every use.
We recommend for you to check the doors, locks, shelves and hinges every three months,
to ensure that the SiteBoss Cabinet can operate fully. If the SiteBoss Cabinet will be under
rigorous use, we recommend integrity checking regularly.
Always carry out integrity checks before lifting the unit.
Apply light oil to hinges for smoother operation.