ARNETOLI MOTOR F 202 BV User manual

F 202 BV saves you time and frustration by providing two ways to lengthen the trimmer line: Bump-n-Go, Manual.
Bump-n-Go (see figure 1) is quick and easy: just tap the bottom of the
head on the ground
an d th e li ne is
lengthened automati-
cally.
Ma nua l (s ee f i gu re
2): just turn the bot-
tom part of the head
to the left to increase
the trimmer line or to the right to shorten the line.
Component /part
BUMP-N-GO
Fig. 2
Fig. 1
101014
PULL
U WI D REWI D
The assembling of F 202 BV cutting head is a very simple operation.
We are talking about a singular cutting head, the only one having an
UNIVERSAL FITTING ITHOUT SHAFT BOLT.
It’s easely mounted as a disk blade.
How to relea e the line
How to mount the F 202 BV
F 202 BV COMPONENTS
To obtain replacement parts, contact your local dealer who supplied you this brush cutter head.
REF. PCS. CODE DESCRIPTION
1 1 C-101044 Upper body ensemble (incl. 2)
2 1 C - 106020 Locking gear
31C-103023 Washer 8 x 24 mm.
41C - 103046 Square head bolt
51C-101052 Central body
61I - 201011 Central body ensemble
7 2 C - 106003 Eyelets
81C-101030 Spool
91I - 202005 Spool ensemble (trimmer line ø 2,4)
10 1 C - 103025 Seeger ring ø 12 mm
11 1C-101053 Lower body
12 1 I - 201003 Lower body ensemble
13 1C-107001 Spring PFM
14 1C-101054 Outer drive
15 1C-101055 Knob
16 1C-102084 Retainer bolt (left)
17 1C-109006 Wrench ø 6
*1 101014 Series of reduction rings
F 202 BV
Instruction Manual
I.M. F 202 BV_2013
ARNETOLI MOTOR S.R.L. - Via Ponte all’olivo - 50066 Reggello (FI) ITALY Tel. [phone] - Fax. [phone] - e-mail: ex [email protected] - www.arnetolimotor.it
2
3
4
5
7
8
10
11
13
14
15
16
17
6
9
12
1

- How to change the trimmer line
- If the line doe n’t come out
YES NO
Changing the trimmer line is a simple operation. Be sure you use a quality trimmer line, otherwise your line will break often
and create unnecessary hassles. We recommend you use our MAXI-LINE - a high resistant line which not only increases the
effectiveness of the brush cutter head but also eliminates any chance of the line getting stuck together.
This can be caused by any of the following reasons.
• Has the line been wound up correctly, without crossing over (fig. 6)?
• Once the outer reel was replaced, did you pull and remove the lines from the retainer slits (fig. 9)?
• Is the trimmer line used of poor quality?
• Is it blocked because the knob is dirty?
Remember that proper maintenance and an occasional cleaning of this tool will not only prolong its' life but also prevent product failure.
Caution
For maximum operator safety, before starting work, in addition to the
deflective shield, we recommend you wear a face shield, one of many
quality accessories offered by AR ETOLI MOTOR.
YES NO
1Unscrew the bottom part of the
head using the apposite wrench
2Take off the outer reel 3Insert the lines in the inner
retainer holes
4Reel the same lines in the middle of
the spool and wind
5Overturn the spool and wind up in the direction
as indicated by the arrows on the side
6The lines must be wound up parallel with each
other and must not cross over each other
7When finished rolling up the line, place the
line in the retainer slits to keep it from unra-
velling (its recommended to leave at least
4 inches of line to ease step number 8)
8Re-insert the outer reel on the
housing
9Once the line is in place, pull the lines
outwards to release them from the slits
ARNETOLI MOTOR S.R.L. - Via Ponte all’olivo - 50066 Reggello (FI) ITALY Tel. [phone] - Fax. [phone] - e-mail: ex [email protected] - www.arnetolimotor.it