ARRI Arriflex 435 Advanced User manual

ARRIFLEX 435 Advanced
Instruction Manual
As of: November 2001
ALL ARTWORK, PICTURES AND TEXTS ARE COVERED BY OUR COPY-RIGHT.
THEY MUST NOT BE COPIED FOR REPRODUCTION (E.G. ON CD-ROM DISKS OR INTERNET-SITES) OR USED IN THEIR ENTIRE FORM OR IN EXCERPTS WITHOUT OUR PREVIOUS WRITTEN AGREEMENT.
IFYOU ARE DOWNLOADING PDF-FILES FROM OUR INTERNET HOME-PAGE FOR YOUR PERSONAL USE, MAKE SURE TO CHECK FOR UPDATED VERSIONS.
WECANNOT TAKE ANY LIABILITY WHATSOEVER FOR DOWNLOADED FILES, AS TECHNICAL DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.

locking grip on
magazine cover
locking grip on
camera door
400 ft magazineeyepiece lock
display
“RUN“-button
operation control indicator
“MODE“-button
“SEL“-button
“PHASE“-button
“SET“-button
“PROG“-button
sliding switch “DISPLAY LOCK“
sliding switch “NORM – PS/CCU“
eyepiece eyecup

tensioning plate
compartment for
TC buffer battery
functional expansion
module (FEM)
mechanical footage indicator
overload display
RS-socket
video optical tap

cover on
magazine opening
main camera switchadjustable
mirror shutter
PL mount
adjustment knob for
manual image
compensation
finder arm
locking key for
manual image
compensation
unlocking key for
finder arm grip system hook for tape focus
power supply
socket
11-pin
accessory socket
overload display
for 11-pin
accessory socket
functional expansion
module FEM
ACC-socket
CCU-socket
ground glass
friction adjustment
finder arm
lock for telescoping
finder arm spirit level
LDS contacts

5
Contents
1. Contents
2. Safety Specifications ......................................9
Warnings ..................................................................9
General Safety Specifications......................................9
Important Notes .........................................................9
Product Specifications ..............................................10
Explanation of the Symbols in the Instruction Manual ..10
3. General Description
of the ARRIFLEX 435 Advanced .................11
4. Installation of the Camera ..........................13
Packing and Transport..............................................13
Tripod Heads ...........................................................13
Horizontal Leveling ..................................................14
Bridge Plates BP-8, BP-9 ...........................................14
Lens Support............................................................16
Grip System ............................................................17
Operation from the Shoulder ....................................19
5. Power Supply ................................................21
Battery NC 24/7 R ..................................................22
Charger NCL 24 R ...................................................22
Mains Unit NG 12/24 R ..........................................23
Mains Unit NG 12/26 R ..........................................23
Accessory Power Supply...........................................24
6. Magazines ......................................................27
Loading the ARRIMAG 120 ......................................28
Removing Exposed Film ............................................31
Transport and Storage ..............................................32
7. Camera Body .................................................33
Electronically Adjustable Mirror Shutter .....................33
Exchanging the Ground Glass ..................................37
Film Gate ................................................................38
Movement ...............................................................41
Attaching the Magazine, Threading the Movement .....42
Pitch Adjustment ......................................................45
Removing the Magazine ...........................................46

6
Contents
8. Optics ..............................................................47
Lenses .....................................................................47
Viewfinder System ...................................................48
9. Camera Operation ........................................55
Main Camera Switch................................................55
Running and Stopping the Camera............................56
Displaying and Setting Operational Parameters .........57
10. Video-Assist-System...................................73
Main Features..........................................................73
The IVS consists of ...................................................75
11. Accessories...................................................79
Anamorphic Viewfinder AVF-2 .................................79
Video Viewfinder VT-2 .............................................81
Work Light WL-3 .....................................................82
Heated Eyecup HE-3 ................................................83
Remote Run Switch RS-4 ...........................................83
Functional Expansion Module FEM ............................84
External Synchronization Unit ESU-1 .........................85
Motion Control Interface MCI-1.................................86
Camera Control Unit CCU-1 .....................................87
Remote Control Unit RCU-1 ....................................101
Wireless Remote Control WRC-1.............................103
Laptop Camera Controller LCC ...............................105
Accessory Socket Distributor (11-pin) ......................106
R/S - Socket Distributor (3-pin) ...............................106

7
Contents
12. Super 35.....................................................107
Converting the Lens Mount Receptacle to Super 35 ...107
Converting the Bridge Plate to Super 35 ..................108
13. Time Code ..................................................109
Time Code Frame Rates ..........................................109
Mounting the Time Code Module ............................110
Checking the Loop Length .......................................111
Setting Film Sensitivity (TCS-Value) ..........................112
Time Code Input ....................................................114
Switching On and Off the Time Code Recording ......117
Time Code Output..................................................117
Time Code and the External Synchronization Unit ESU-1 ... 118
Time Code Buffer Battery ........................................118
Overview of the Display Indications
in Time Code Operation ....................................120
14. Maintenance ..............................................123
Camera ................................................................124
Cleaning the Spacer Gate ......................................126
Cleaning the Field Lens ...........................................127
Magazine .............................................................128
15. Appendix ...................................................131
16. Technical Data ...........................................139
17. Order Numbers.........................................141
18. ARRI Service ..............................................143
19. Index ...........................................................145

8
Contents

9
2. Safety Specifications
Warnings
Note: Operational error possible!
Danger of injury
or equipment damage possible!
General Safety Specifications
Attention! Danger of injury! Never place your
hand in the lens mount receptacle or the inside
of the camera while it is running.
• In order to ensure optimal performance, it is essential
that you acquaint yourself with this instruction manual.
• Assembly and initial operation should be carried out
only by persons who are familiar with the equipment!
• Switch off the main camera switch before making
electrical connections (i.e. plugging on motion control etc.)!
• Never run the camera or bring the camera in motion
control mode without a lens or a protective cap in the
lens mount receptacle!
• Never operate the movement locking mechanism while
the camera is running or in motion control mode!
• Ensure that the camera is stabily positioned!
• Remove the battery cable before transport or servicing!
• Repairs should be carried out only by authorized
service centers!
• Use only original ARRI replacement parts and accessories!
Important Notes
• In wet weather the normal safety precautions for
handling electrical equipment should be taken.
• Avoid operational errors!
Safety Specifications

10
• Clean optical surfaces only with a lens brush or a clean
lens cloth! In cases of solid dirt moisten a lens cloth with
pure alcohol.
• Do not use solvents in cleaning the film gate!
• Do not remove any screws which are secured with paint!
Product Specifications
In the case of enquiries or when ordering parts, please
advise camera serial number and model.
Note: This instruction manual applies only to the
ARRIFLEX 435 Advanced.
Explanation of the Symbols
in the Instruction Manual
➪ photo indicates objects which are shown in the photo-
graphs or drawings.
Note:
This product and the accessories recommended by the
manufacturer fulfill the specifications of the EU-Guideline
89/336/EWG.
Attention:
To use the Single Frame Handcontroler (SFHC)
together with the ARRIFLEX 435 Advanced,
software version S02.00 or higher must be
installed in the camera.
The software version can be displayed on the
camera‘s left display, as described in chapter 9
(Camera Operation/ Displaying and Setting
Operational Parameters/ Overview of Display
Modes/ Mode 8 – on page 59).
To update your camera software, please contact
a ARRI service center for instructions.
If you are operating the ARRIFLEX 435 Advanced
together with the SFHC, do not modify any
parameters on the SFHC for the first three seconds
after powering up the camera (as long as the
display on the left camera side is not showing
any information). If you have modified anything
during this time period, please disconnect the
SFHC and reconnect it to reset the SFHC.
Safety Specifications

11
3. General Description of the ARRIFLEX 435 Advanced
The ARRIFLEX 435 Advanced is a compact, light-weight
MOS- and HS-camera. Due to the modular design of the
camera, its range of functions can be individually expanded.
The following features are already integrated into the
basic version of the ARRIFLEX 435 Advanced.
• Operational parameters can be set directly on the camera.
• The frame rates range from 0.1 – 150 fps for forward
or reverse running.
• The ARRIFLEX 435 Advanced is equipped with a low-
main-tenance, 5-link movement with dual transport
claws and registration pins.
• The electronic mirror shutter on the ARRIFLEX 435 Advanced
can be set continuously from 11.2°to 180°while the
camera is running.
• The viewfinder can be rotated in two axes and can be
used on both sides of the camera with full image
compensation.
• Via an integrated optical tap, a 1/2" CCD video camera
can be attached.
• The versatile grip system is connected directly to the
camera body and can be used as a carrying handle
or as an accessory holder.
A comprehensive range of optical, mechanical and electronic
accessories further expands the operational possibilities of
the camera.
General Description

12
Installation
magazine
opening cover
movement
in locked position loop protector

13
4. Installation of the Camera
Packing and Transport
In order to prevent damage to the mirror shutter,
a protective cap must be on the lens mount
receptacle at all times.
When transporting the camera, pay attention that
the movement is in the locked position ➪ photo.
If the ARRIFLEX 435 Advanced is transported or
stored without a magazine, the magazine
opening cover ➪ photo should be attached.
Loaded or empty magazines should only be trans-
ported or stored with the loop protector ➪ photo
attached to avoid damage to the film stock and
the magazine throat assembly.
Tripod Heads
The following tripod heads are suitable for use with the
435 Advanced:
• ARRIHEAD
• ARRIHEAD 2
• ARRIHEAD 2 with integrated encoders
• ARRI Fluid-Heads
• Sachtler Studio 7, 150 H
• Mitchell-Head
• Moy-Head
• Ronford F7
• Hot-Head
• Cam-Remote-Head
• Worall-Head
In applications where the camera mount is subject
to high forces (e.g. helicopter mounts) the camera
must be additionally secured with retaining cords.
All fastening screws must be tightened firmly with
an appropriate screwdriver (not with the commonly
used coin!).
Installation

14
Horizontal Leveling
The ARRIFLEX 435/435ES is equipped with a spirit level
to aid horizontal leveling of the camera ➪ photo.
If the camera is set on a level surface with the
magazine in place, the camera may tip back, as
the center of gravity is located far to the rear.
Bridge Plates BP-8, BP-9
The bridge plates facilitate balancing of the camera on the
tripod and mounting of accessories. The BP-8 is designed
for 19 mm support rods, the BP-9 for 15 mm support rods.
The bridge plates consist of the base plate ➪ photo, the
sliding upper plate ➪ photo and a pair of support rods
➪ photo. In the standard version the support rods are
440mm long. Optionally, support rods are available in
the lengths 240mm and 340mm.
Note: The upper plate of the bridge plate can be con-
verted for use with Super 35. This ensures that
the accessories are also exactly adapted to the
displaced optical center of the Super 35 format.
See also Chapter 12, Super 35 .
Installation
spirit level
sliding
upper plate
base plate
support rods

15
Attaching the Bridge Plate to the Camera
• Fasten the sliding upper plate ➪ photo with the two slit
screws to the camera base. Both cylindrical pins ➪ photo
(twist prevention) must glide into the holes.
• Then screw the base plate onto the wedge plate of the
tripod and lock onto the tripod head.
• Slide the camera with the upper plate into the dovetail-
guide of the base plate until the spring-loaded stop pin
➪ photo snaps back audibly. The camera’s position can
then be fixed with the clamp lever.
• Slide the support rods into the guides and clamp.
• Equip the camera with the required accessories to
determine the center of gravity. Loosen the clamping
lever ➪ photo, and by sliding the camera on the base
plate find the optimal position. Then retighten the
clamping lever.
Removing the Camera from the Tripod
• Before removing the camera make sure that all cables are
disconnected and that the eyepiece leveling rod is de-
tached.
• For fast removal of the camera from the tripod, loosen the
clamping lever ➪ photo, push in the stop pin ➪ photo
and then pull the camera with the upper plate ➪ photo
from the base plate.
Installation
screws
clamping lever
sliding upper plate
cylindrical pins
sliding upper plate
base plate
stop pin

16
Lens Support
The lens support consists of the lens support LS-7 (can be
snapped onto 19 mm support rods) ➪ photo or the lens
support LS-8 (can be pushed onto 15 mm support rods) and
the respective lens support ring ➪ photo for the lens in use.
• Mount the lens support onto the support rods from above
and let it click into place by applying slight pressure
(push the LS-8 onto the support rods from the front).
• Slide the relevant support ring ➪ photo onto the lens
but do not tighten.
• Then slide the lens into the lens mount receptacle and lock.
• Connect the support ring to the lens support and
tighten the knurled screw ➪ photo as well as the
clamping lever ➪ photo.
• Complete the process by tightening the clamp screw
➪ photo on the support ring.
Note: Mounting the support ring on the relevant lens is
usually carried out only once. The support ring
can then remain in position on the lens.
Installation
lens support ring clamp screwlens support
LS-8
lens support
LS-7
knurled
screw
clamping lever wedge plate
base
plate

17
Grip System
The multipurpose grip system on the ARRIFLEX 435/435ES
guarantees highest stability through its fixed connection to
the camera body and provides numerous possibilities for
attaching accessories. Five 3/8" inner threads allow
attachment in diverse positions ➪ photo.
Attaching Additional Handgrips
Additional handgrips can be screwed onto the grip system
in various positions as required. A safety mechanism in the
handgrip prevents automatic loosening. This mechanism is
activated by screwing in the handgrips tightly.
Before screwing in the handgrips, make sure
that the 3/8" threaded bolt is completely
screwed out of the handgrip.
Removing the Grip System
In order to minimize camera height, the entire grip system
can be removed.
• First remove the magazine.
• Loosen both the hexagon screws ➪ photo in the strut
and pull the grip system ➪ photo upwards.
To attach the grip system, proceed in the reverse order.
Installation
grip system
hexagon screws

18
Installation
shoulder set S-4 shoulder cushionbase plate

19
Operation from the Shoulder
Shoulder Set S-4
The shoulder set S-4 was designed to optimize shoulder
operation of the ARRIFLEX 435 Advanced. It allows the
camera to be quickly transferred from the tripod onto the
operator’s shoulder without having to remove the optical
accessories.
Shoulder Set S-4 with the Bridge Plate
• Remove the camera from the tripod
(see under Bridge Plates BP-8, BP-9 ).
• The mounting screws on the shoulder set must first be
screwed back as far as they will go ➪ photo.
• Now slide the shoulder set from the rear into the dovetail-
guide on the bridge plate as far as it will go. It locks auto-
matically in position.
• Clamp the shoulder set using the bridge plate clamping
lever.
• Plug the cable for starting and stopping the camera
into the RS-socket.
• Check that the shoulder set is firmly seated on the camera.
• Position the shoulder cushion on the camera with the
index pin and fasten it to the camera with the mounting
screw ➪ photo.
• Check that the shoulder cushion is firmly seated on the
camera.
Installation
mounting screws
mounting screw
shoulder set S-4

20
Shoulder Set S-4 without the Bridge Plate
• Remove the camera from the tripod.
• Detach the bridge plate.
• Position the shoulder set on the camera and fasten with
the two mounting screws.
• Plug the cable for starting and stopping the camera into
the RS-socket.
• Check that the shoulder set is firmly seated on the camera.
• Position the shoulder cushion on the camera with the
index pin and fasten it to the camera with the mounting
screw.
• Check that the shoulder cushion is firmly seated on the
camera.
Operation from the Shoulder
without the Shoulder Set
The shoulder cushion can be used with or without the
bridge plates BP-8 and BP-9.
• Position the shoulder cushion on the camera with the index
pin and fasten it to the camera with the mounting screw.
• Check that the shoulder cushion is firmly seated on the
camera.
• Position the handgrip on the rosette and fasten with the
fastening screw ➪ photo.
• Plug the cable for starting and stopping the camera into
the RS-socket.
Installation
fastening screw
handgrip
„RUN“-button
RS-socket