Arrow Storage Products EZEE SHED EZ10872HVCREU Instructions for use

Gloves must be worn
at all times to reduce
risk of injury!
Owner’s Manual
& Assembly Guide
01CH
722750517
EZ10872HVCR
EZ10872HVCRCC
EZ10872HVCC
EZ10872HVCCCR
www.arrowsheds.com
BUILDING DIMENSIONS
* See Inside for Detailed Safety Information.
Size rounded off to the nearest foot
Exterior Dimensions
(Roof Edge to Roof Edge)
Width Depth Height
Interior Dimensions
(Wall to Wall)
Width Depth Height
Door
Opening
Width Height
Approx.
Size
Storage
Area
10’ x 8’ 71 Sq. Ft. 502 Cu. Ft. 117 3/4” 98” 98” 114” 90” 97” 63 1/2” 69 3/4”
3,0 m x 2,4 m 6,6 m214,2 m3299 cm 249 cm 249 cm 289,6 cm 228,6 cm 246,4 cm 161,3 cm 177,2 cm
For proper base construction see page 14
Base
Size
116 1/2” x 92 1/2”
296 cm x 235 cm
†
†
Nominal Size
10’ x 8’
Customer Service:
1-800-851-1085 or
[email protected]
EZ10872HVCREU
EZ10872HVCRCCEU
EZ10872HVCCEU
EZ10872HVCCCREU
Model No.
EZEE SHEDTM

GB: Assembly manual in additional languages available online.
Scan QR code below to access.
FR: Manuel de montage disponible en ligne dans d’autres langues.
Pour y accéder, scannez le code QR ci-dessous.
SP: Manual de montaje en idiomas adicionales disponible online.
Escanee el código QR a continuación para acceder.
DE: Montageanleitung in zusätzlichen Sprachen online verfügbar.
Scannen Sie den QR-Code unten, um darauf zuzugreifen.
I T: Manuale dell’assemblea in altre lingue disponibile online.
Per accedere effettua la scansione del codice QR in basso.
P T: Manual de montagem disponível em outros idiomas online.
Digitalize o código QR abaixo para obter acesso.
D T: Samlingshåndbog i yderligere sprog til rådighed online.
Scan QR kode nedenunder for at få adgang.
SK:Nainternetejekdispozíciinávodnazostavenievďalšíchjazykoch.
Dostanete sa k nemu naskenovaním kódu QR.
CZ:Návodkmontáživdalšíchjazycíchjekdispozicivonlineverzi.
 PřístupzískáteponaskenováníQRkóduníže.
HU: Azösszeszerelésiútmutatótovábbinyelvekeniselérhetőonline.
A hozzáféréshez olvassa be az alábbi QR-kódot.
GR: Υπάρχειδιαθέσιμοστοδιαδίκτυοτοεγχειρίδιοσυναρμολόγησης
 σεπερισσότερεςγλώσσες.Σαρώστετονπαρακάτωκώδικα 
 QRγιανααποκτήσετεπρόσβαση.
P/N 6PP722621216

2
SAFETY PRECAUTIONS...
Safety precautions MUST be followed at all times throughout the construction of your building!
Care must be taken when handling various pieces
of your building since many contain sharp edges.
Please wear work gloves, eye protection and
long sleeves when assembling or performing any
maintenance on your building.
Practice caution with the tools being used in the
assembly of this building. Be especially familiar with
the operation of all power tools.
Keep children and pets away from the worksite
during construction and until the building is
completely assembled. This will help avoid
distractions and any accidents which may occur.
NEVER concentrate your weight on the roof of the
building. When using a step ladder make sure that
it is fully open and on even ground before climbing
on it.
Do NOT attempt to assemble your building on a
windy day. The large panels can catch the wind like
a “sail”, causing them to be whipped around making
construction diffi cult and unsafe.
Do NOT attempt to assemble your building before
double checking that you have all the parts indicated
in the parts lists (page 9) as well as all hardware
(page 8). Any building left partially assembled may
be seriously damaged by even light winds.
IMPORTANT NOTE ON ANCHORING
• Your building MUST be anchored to prevent wind
damage. An anchoring kit is not supplied with your
building and you have many options when it comes to
anchoring. See anchoring page for more info.
• You must also have a temporary anchoring system in
place in case you need to take a break from assembly.
See page 4 for more info.
02CG

3
ASSEMBLY TIPS &TOOLS
How to Select and Prepare Your Building Site: Before you start to assemble your
building, you will want to decide on a good location. The best location is a level area with good drainage.
• Allow enough working space so it is not diffi cult to move parts into position for assembly. Be sure there will be enough
space at the entrance for the doors to completely open. Also, there needs to be enough space outside the building to be
able to fasten the panel screws from the outside.
• Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Watch the Weather Closely: Be sure the day you choose to install your building is dry and calm.
Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Use Teamwork: Two or more people are required to assemble your building. One person can hold
the parts or panels in place while the other person fastens them together and handles the tools. This
makes the process of assembling your building faster and safer.
Tools and Materials: Here is a list of some basic tools and materials you will need to assemble
your building. Decide which method of anchoring and the type of base you will use to make a complete
list of the materials you will need.
• Work Gloves
• Safety Glasses
• Step Ladder
• No. 2 Phillips Screwdriver (Magnetic Tip Preferred)
• Utility Knife or Scissors
• Pliers
• Carpenter’s Level
• Tape Measure
• Power Drill (Cordless, Variable Speed)
• Nut Driver or Wrench
• Square
• String (for squaring the frame)
• Awl (to align holes)
• Lumber and/or Concrete
• Hammer and Nails
• Spade or Shovel
• Hand Saw or Power Saw
WHAT YOU NEED
RECOMMENDED TIME SAVERS
BASE PREPARATION TOOLS
03A

4
FREQUENTLY ASKED QUESTIONS
Q. How long will it take to assemble the building?
A. Assembly time depends on a variety of factors, including roof design, tools available, DIY skill and the pace
at which you work. Guidelines for each shed assembly are approximate AFTER completion of the base, and
assume two or more people working on the assembly. Generally, you should plan on at least one day working with
someone who can assist you; again, after constructing the base. Refer to the clock icons on each product page
on the website for specifi c time estimates.
Q. How do I decide where to put my shed?
A. The key to a successful assembly is to make sure the shed will be square and level when built. The shed can
be assembled directly onto level ground (grass or dirt). If you have location options, choose one that is already
fl at, with good drainage to control moisture. If you don’t have a fl at, well-drained area, you need to prepare the
space. Level the area using cinder blocks, concrete, crushed gravel or other sturdy materials. Once level with good
drainage, construct your base. Using a carpenter’s level, make sure your base is level and free of bumps or ridges
to provide good support for your building.
Q. What if I can’t fi nish my building in one session?
A. If weather conditions change so that it becomes windy or rainy, it is recommended that you stop assembly
until conditions improve. This is for your safety and for protection of the shed panels. However, do not leave
your unfi nished construction without fi rst temporarily anchoring the corners of the shed to your base and placing
weights, such as patio blocks or sandbags, on the fl oor frame. Failure to anchor the building if you leave it while
partially assembled could result in irreparable damage or personal injury if the building collapses.
Note: Most instruction manuals provide a warning note at the beginning of the installation step for corner panels,
stating that the remainder of the building assembly requires multiple hours and more than one person. Do not
continue beyond this point if you do not have enough time or help to complete the assembly that day. A partially
assembled building can be severely damaged by even light winds.
Q. Do I need to anchor my building?
A. Yes! Fully assembled buildings should be anchored using a permanent anchoring system. If you need to leave
your building before it is completely assembled, you will need to temporarily anchor the corners of the shed to your
base, and place weights, such as patio blocks or sandbags, on top of the fl oor frame.
Q. How do I temporarily anchor my building before it’s fully assembled?
A. An incomplete building must be anchored before breaking for any period of time to prevent possible damage.
•If the building is on a wood base, secure the frame with wood screws in the corners
•If the building is on a concrete base, temporarily anchor the frame in the corners
•Use patio blocks or sandbags on top of the fl oor frame as weights
•Secure the fl oor frame to the ground with ground augers or rope the frame in the corners to the ground
Q. How do I control condensation and prevent water from leaking in?
A. To minimize condensation, install a continuous, unbroken plastic vapor barrier with a thickness of 6 mil.
between exposed ground surface and the building’s base. Make sure that all weather stripping and washers are
used throughout the assembly process. Make sure that the weather-stripping tape adheres to the panels when
installing it along the main ridge beam. Do not stretch it. Apply it directly off the roll onto clean panels. Ensure
that all washers are fl ush with the panels and do not over-tighten screws, as this can crack the washers. Silicone
caulking may be used to create watertight seals at the washers and throughout the building.
04A

5
Q. What kind of base do I use?
A. You can:
•Use an Arrow Base Kit
•Pour a concrete slab
•Build a wood deck/fl oor (use exterior-grade plywood)
•Use patio blocks
•Build on crushed gravel, dirt or grass
Arrow provides a base kit accessory that is an option for most building sizes. If you are building a wood deck/fl oor,
an Arrow fl oor frame kit on top of your deck/fl oor assembles in minutes and provides a fl oor frame suitable for a
5/8” exterior-grade plywood fl oor (not included). A continuous unbroken plastic vapor barrier with a thickness of 6
mil. between the ground and the building’s base is also recommended.
Q. How should I measure for my base?
A. Shed dimensions are provided in “nominal” size. Nominal sizes are roof-edge measurements rounded to the
nearest foot and are not the measurements to use for constructing the shed base. So, carefully check the exact,
recommended base size in the specifi cations for your shed model.
Q. How do I align the holes in the wall panels with the holes in the fl oor frame?
A. Make sure that the shed is level and square, with the correct fl oor frame size, and that the corner panels are
installed correctly. Line up the large hole in the panel with the small holes in the fl oor frame. An awl can be used to
help align the holes.
Q. How do I align the holes in the roof panels with the holes in the roof beam and side wall angles?
A. Your building must be level and square in order for the holes to align. It must be square at both the top and
bottom. Check that the building is square by measuring diagonally. The two diagonal measurements will be equal.
If your building is out of square, carefully rock and push the shed until it is square. Also, try loosening the roof
beams to give more play and fl exibility. Non-alignment can also occur if your building is not level. You can raise
corners and shim under them to make it level. Check that the panels are installed in the proper location. The
building should not be permanently anchored until the complete unit is assembled; otherwise, you will not be able
to make adjustments for squareness during assembly. Do not attach the bottom of the roof panels to the side wall
angles until all the roof panels are up.
Note: If you have to stop assembly for any reason before it is complete, do not leave your unfi nished construction
without fi rst temporarily anchoring the corners of the shed to your base and placing weights, such as patio blocks
or sandbags, on the fl oor frame.
Q. How do I ensure that the sliding doors on the building will hang level?
A. Make sure that the door track has been correctly installed, with the long leg on top and the short leg on the
bottom. Check that the door slides are straddling the upper and lower legs of the door track assembly, putting the
door slide only halfway in the track. Also, the rounded end of the door slide should be at the bottom and the square
end at the top.
Q. What kind of customer support is available?
A. Our instruction manuals contain step-by-step assembly illustrations and guide you from preparation through
assembly to care and maintenance of your fi nished building. Each part is marked with a factory number for easy
identifi cation. In addition, our assembly animation (located under the Customer Support menu on the website)
provides helpful tips. But if you need to reach someone at Arrow, you can contact Arrow Customer Service, toll free,
at 1-800-851-1085 (press 1) or via e-mail at [email protected]. Have your model number and instruction
manual with you when you call.
05A

6
Q. What if the rear wall angle and channels are too large to fi t inside of the rear wall panels?
A. Check the dimensions of wall assemblies. They should be slightly smaller than the fl oor frames. Lay the
assemblies on top of the rear fl oor frame and pull them up to the top of the wall panels causing the corner panels
to stand erect and not lean inward. Caution: Be careful to not scratch the panels on the way up.
Q. The wide rib always overlaps the crimped rib. Is there ever an exception?
A. This sequence is to be followed through the assembly process. However, this will typically happen once on the
rear and once on each side wall (vertical wall units only) where there will be either two crimped ribs overlapping or
two wide ribs overlapping. This may give it a tighter fi t, but it will work.
Q. Can the building be painted?
A. The buildings can be painted with an exterior-grade paint designed for use on steel. Contact your local paint
supplier for recommendations.
Q. I heard that rust might be an issue with steel; is it?
A. While steel can rust, with proper care this should not be an issue. For a long-lasting fi nish, periodically clean
the exterior surface and apply spray-on car wax. Touch up scratches as soon as you notice them by immediately
cleaning the area with a wire brush or emery paper, washing it and applying touch-up paint. This will minimize rust
and maintain your shed’s attractive appearance for years.
Q. How do I take care of dents in my shed?
A. Proper selection of shed size, including a suffi cient door-opening width, and proper placement of your shed
should minimize the possibility of damage. If a dent does occur, carefully push the dent out from the opposite side.
If the paint has been scratched or removed, touch up the area as soon as you notice it. Immediately clean the area
with a wire brush or emery paper, wash it and apply touch-up paint. This will minimize rust and maintain your shed’s
attractive appearance for years.
Still have questions? Visit us online at www.arrowsheds.com to view lots of helpful tips and information
regarding all of our available products. You can also contact our Customer Service team at 1-800-851-1085
(press 1), or via e-mail at [email protected].
06A
At the top of each page you will see one or more Part
Cues like the one to the left. These Part Cues are
designed to help you quickly identify the parts needed
for each step.
##### 5
Part No. Quantity Needed
End View
Part Name Part Name
Confi rm that all hardware and parts are
present before attempting to assemble
your building.
Customer Service:
1-800-851-1085 or
[email protected]
For missing or damaged parts contact
Customer Service. Do not return to store.
Part Numbers
Part Number
1. Each part has an identifying part number on it.
2. Part Numbers are referenced in each step.
3. Unpainted parts have a stamped in number and painted
parts have a number that is inked on.
Remove inked on numbers with soap and water after assembly.

CARE &MAINTENANCE...
Exterior Care:
For a long lasting fi nish, clean and wax the exterior surface. We recommend washing with a mild soap solution. DO
NOT use power washing to clean your shed. Using a spray automotive type wax periodically on the exterior is highly
recommended if you are in a high humidity or coastal climate region.
Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible
storage. Corrosive chemicals such as fertilizers, pesticides and herbicides should be cleaned off the interior and
exterior surfaces immediately. Rust caused by chemical damage is not covered by the warranty.
DO NOT STORE POOL CHEMICALS IN YOUR SHED - THIS VOIDS YOUR WARRANTY
Rust protection precautions may help to stop rust from developing, or stop it quickly as soon as it appears.
• Avoid nicking or scraping the coating surface, inside and out.
• Keep roof, base perimeter and door tracks free of debris and leaves which may accumulate and retain moisture.
These can do double damage since they give off acid as they decay.
• Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of
moisture, oils, dirt or grime and then apply an even fi lm of high quality touch-up paint.
• Various paint manufacturers provide products for rust treatment and coverage. If surface rust does appear on
your shed we recommend treating those areas as soon as possible, following the paint supplier of your choice
instructions.
• Our customer service department can provide the paint tinting formula for matching the color of your shed. We also
have touch-up paint available for repairing small nicks and scratches.
Roof:
Keep the roof clear of leaves and snow. Heavy amounts of snow on the roof can damage the building making it
unsafe to enter. In snow country, Roof Strenghtening Kits are available for most Arrow Buildings for added protection
against heavy snow accumulation.
Doors:
For sliding doors, always keep door tracks clear of dirt and other debris that prevents them from sliding easily.
Lubricate door track annually with furniture polish or silicone spray. Keep doors closed and locked to prevent wind
damage.
Fasteners:
Use all washers supplied to protect against weather infi ltration and to protect the metal from being scratched by
the screws. Regularly check screws, bolts, nuts, etc., and retighten as necessary.
General:
• A plastic sheet (vapor barrier) placed under the entire fl oor area may reduce condensation.
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the building.
Keep these assembly instructions and owner’s manual for future reference.
Please note, Manufacturer cannot be held responsible for any consequences due to buildings that are not installed
per these instructions, or for damage due to weather conditions or acts of God.
44A
7

8
HARDWARE LIST...
Hardware Views by Key No.
08CH
2
11/32 Hex.
1
#2 Phillips
3
#2 Phillips
Key Part Part Qty.
No. No. Description List
1 65923 Bolt (#8-32 x 3/8) (10 mm) 84
2 65103 Hex Nut (#8-32) 84
3 65004 Screw (#8AB x 5/16) (8 mm) 224
4 66646 Washer Sheet 4
5 66715 Door Handle 1
6 66718 Hinge 6
7 66720 Padlock Eyelet 1
8 60H Corner Cap 4
9 66860 Peak Cap 2
9
6
The fasteners used in each step are shown
actual size at the top of each page. If you
are unsure which fastener to use, hold it up
to the picture and use the one that matches.
8
4
5
7
10
10 66847 Vent Gable 4
11 66719 Spring Pin Upper 1
12 66713 Spring Pin Lower 1
13 66721 U-Nut (Door Clip) 12
14 10280 Corner Clip 8
11 12
13 14

6
38 11051 Roof Beam Brace 4
39 11053 Door Jamb Support 2
PARTS LIST...
9
Key Part Part Qty.
No. No. Description List Selected End Views by Key No.
7
13 14 16,31,32
17,21
10,11,15 12
6
2 & 91,3,4,5,8
09CH
1 11035 Floor Channel (unpainted) 4
2 11034 Ramp (unpainted) 1
3 10275 Door Brace Horizontal (painted) 4
4 11017 Door Brace Vertical (painted) 2
5 11027 Door Brace Vertical (painted) 1
6 11024 Door Jamb 2
7 10288 Door Brace Diagonal 4
8 10336 Roof Channel (painted) 4
9 11033 Header Trim (painted) 1
10 11037 Wall Channel (painted) 4
11 10340 Floor Channel (unpainted) 4
12 11038 Ridge Beam 8
13 11040 Roof Beam Bracket 4
14 11030 Gable Brace 2
15 10337 Roof Channel (painted) 4
16 11039 Fascia Trim (painted) 4
17 11022 Ridge Cap 1
18 11041 Roof Beam Brace 2
19 11008 Door Panel 2
20 11009 Door Panel 2
21 11032 Ridge Cap 1
22 10999 Panel Wall 3
23 11000 Corner Panel 4
24 10998 Panel Wall 22
25 11036 Gable Right 2
26 80123 Gable Left 2
27 11014 Roof Panel 12
28 80121 Roof Panel Left 2
29 11015 Roof Panel Right 2
18
30 11019 Channel Splice 10
31 10341 Wall Channel (painted) 4
32 11026 Vertical Door Brace (painted) 1
33 11025 Door Astragal 1
34 11031 Header Angle 1
35 11004 Panel Wall 2
36 11002 Door Panel 2
37 11028 Channel Splice 2
30,37
33 34 38
39

ASSEMBLY BY KEY NO.
10
10CH
Walls
Floor
1
6
6
37
37
9
30
11 11
35
35
22
22
22
23
23
23
23
24
24
24 24
24
24
24
24
24
24
31
31
24
10
10
10
10
11
30
30
30
30
11
1
1
1
24
24
24
24 24
30
34
2
24
24
24 24
24
24
31
31

ASSEMBLY BY KEY NO.
11
11CH
Roof
Doors
7
3
3
4
19
20
32
7
13
13
13
13
14 18
18
25
25
26
26
12
12
12
12
12
12
12
12
8
8
8
8
15
15
15
15
16
16
16
16
21
17
27
27 27 27
27
27
27 27
27 27
28
28
29
29
30
30
30
30
36
33
3
3
419 20 36 5
7
7
38
38
38
38
14
27
27

12
ASSEMBLY OVERVIEW
Build Side Wall Assemblies Build Rear Wall Assembly
Build Front Wall Assembly Assemble Walls
Build Roof Assemblies Install Gables and Roof Beam
12CH

13
ASSEMBLY OVERVIEW
Install Roof Panels Install Trim
13CH
Install the Door and you
now have a fi nished shed

14
CONSTRUCTING A BASE...
FRONT
(DOOR)
FRONT
(DOOR)
Note: Finished Slab dimensions, with lumber removed.
OPTION 1: Directly on ground (earth)
Assemble your building directly on level ground (grass, dirt, rock, sand, etc.).
Allow 1 - 2 hours for construction.
OPTION 2: Wood Platform
If you decide to build your own base, be sure to select the appropriate materials.
These are the recommended materials for your base:
• 2 x 4's (38 mm x 89 mm) Pressure Treated Lumber • 5/8" (15,5 mm) 4 x 8 (1220 mm x 2440 mm) Plywood-exterior grade
• 10 & 4 penny Galvanized Nails • Concrete Blocks (optional)
NOTE: Pressure Treated Lumber must not be used where it will make contact with your storage building. The properties of
Pressure Treated Lumber will cause accelerated corrosion. If Pressure Treated Lumber comes in contact with your storage
building your warranty will be voided.
The platform should be level and fl at (free of bumps, ridges etc.)
to provide good support for the building. The necessary materials
may be obtained from your local lumber yard.
To construct the base follow instructions and diagram.
Construct frame (using 10 penny galvanized nails)
Measure 16"/24" (40,6 cm/61,0 cm) sections to construct
inside frame (see diagram)
Secure plywood to frame (using 4 penny galvanized nails)
Allow 6 - 7 hours for construction.
OPTION 3: Concrete Slab
The slab should be at least 4" (10,2 cm) thick. It must be level
and fl at to provide good support for the frame.
The following are the recommended materials for your base.
• 1 x 4's (19 mm x 89 mm) (will be removed once the concrete cures)
• Concrete • Sheet of 6 mil plastic
• We recommend for a proper strength concrete to use a mix of:
1 part cement • 3 parts pea sized gravel • 2 1/2 parts clean sand
Prepare the Site/Construct a Base
1. Dig a square, 6" (15,2 cm) deep into the ground (remove grass).
2. Fill up to 4" (10,2 cm) in the square with gravel and tamp fi rm.
3. Cover gravel with a sheet of 6 mil plastic.
4. Construct a wood frame using four planks of 1x4 (19 mm x 89 mm)
lumber.
5. Pour in concrete to fi ll in the hole and the frame giving a
total of 4" (10,2 cm) thick concrete. Be sure surface is level.
Allow 3 - 5 hours for construction and a week for concrete curing time.
Note: Platform/Slab will extend 9/16" (1,4 cm) beyond
fl oor frame on all four sides. Seal this 9/16" (1,4 cm)
of wood with a roofi ng cement (not included), or bevel
this 9/16" (1,4 cm) of concrete when pouring, for good
water drainage.
116 1/2”
296 cm
16"/24"
40,6 cm/61,0 cm
92 1/2"
235 cm
14CH
116 1/2”
296 cm
92 1/2"
235 cm

15
Step 1: Side Walls
15CH
You will need for this page:
Wall Channel
4
10341
Turn Channel over and
insert Channel Splice.
Use Tapered end to start.
Floor Channel
4
10340
Channel
Splice
11019
Make two (2) Wall Channel
Assemblies (Painted).
Make two (2) Floor Channel
Assemblies (Unpainted).
4
10341
10341
10341
10341
11019
11019
10340
10340
10340
10340
11019
11019
Use rubber mallet and
gently tap Channel Splice
intoChanneluntill mounting
holes align.
Wall Channel Assemblies (Painted) Floor Channel Assemblies (Unpainted)
(QTY: 4)
(QTY: 4)
11019
11019
12"
30,5 cm
Join Channels and
screw together.
10341
10341
10340
10340
1
2
3
4
5

16
Be cautious when maneuvering and placing
Panels. Once Panels begin to go up it is important
to be able to fi nish in a timely manner to reduce
the possibility of wind damage to your building.
You will need for this page:
Step 1: Side Walls
10999
10998
10998 10998
16CH
Panel Wall
12
10998
Panel Wall
2
10999
Corner Panel
2
11000
ARROW TO TOP
11000
Make two (2) Side Wall Sections.
7 panels & 1 corner - each
6
10998 10998
VERIFY PANELS ARE POSITIONED
IN CORRECT SEQUENCE BY PART
NUMBER
10998

17
Step 1: Side Walls
17CG
Bring Top Panel down fl at while
maintaining pressure in the middle
to keep edge hooked.
Start in middle of assembly to snap
Panels together.
Push down to snap Panels together
working from center outward in both
directions.
Push down to snap end of
Panels together.
Apply pressure in
area shown
10998
10998
Always cover
the Arrow.
Raise Panel at Angle.
7
Hook Edge of Top Panel to
Bottom Panel.
9
8
Overlap Panels
and Align Ends.
ALWAYS COVER
THE ARROW
MUST USE FLAT SOLID
SURFACE. DO NOT SNAP ON
GROUND OR GRASS
maintaining
pressure
Top Panel
Bottom Panel
Top Panel
Bottom Panel
12
10
11
13

18
Step 1: Side Walls
18CH
ARROW TO TOP
11000
Install Corner Panel.
You will need for this page:
Use edge of surface,
like your carton, to allow
Corner Panel to hang
down.
Cover Arrow on Corner
Panel.
Push down to snap Panels
together working from the
center in each direction .
CORNER PANEL
Attach Corner Panel to Wall
Panel using four (4) washers
and screws.
(QTY: 8)
10999
14
15
16
17
18

19
Step 1: Side Walls
19CH
Attach Wall Channel
Assembly (Painted).
You will need for this page:
Wall Channel
Assembly
2
19
Channel
START ASSEMBLY AT CORNER PANEL
CORNER MUST BE AGAINST
45 DEGREE CUT ON CHANNEL
IMPORTANT
ELEVATE PANELS TO MAKE
INSTALLING WALL CHANNEL
ASSEMBLY EASIER
Align Wall Channel Assembly
to Panel Ribs and pop into
place at Corner.
WALL CHANNEL ASSEMBLY
(Painted)
ELEVATED PLATFORM
Continue aligning
Channel Assembly
and popping into place.
20
21
ARROW TO TOP
1. Angle Wall Channel Assembly 3. Complete Wall Channel
Assembly Install.
2. Continue to align Wall Channel
Assembly onto Wall Panels
Channel Wall Panels
Channel Wall Panels
Wall Panels
Channel