Art's Way Roda V140 Setup guide

Art’s-Way Manufacturing Co., Inc.
Model V140
Manure Spreader
Operator’s Manual & Illustrated Parts List
H610122
Issued April 2014
By
OPERATOR’S MANUAL

This symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS IN-
VOLVED. The message that follows the symbol contains important information
about your safety. Carefully read the message. Make sure you fully understand the
causes of possible injury or death.
IF THIS MACHINE IS USED BY AN EMPLOYEE, IS LOANED, OR IS RENTED, MAKE
SURE THAT THE OPERATOR UNDERSTANDS THE TWO INSTRUCTIONS BELOW.
BEFORE THE OPERATOR STARTS THE ENGINE:
GIVE INSTRUCTIONS TO THE OPERATOR ON SAFE AND CORRECT USE OF THE
MACHINE.
MAKE SURE THE OPERATOR READS AND UNDERSTANDS THE OPERATOR’S MANU-
AL FOR THIS MACHINE.
WARNING
IMPROPER OPERATION OF THIS MACHINE CAN CAUSE INJURY OR DEATH.
BEFORE STARTING THE ENGINE, DO THE FOLLOWING:
1. READ THE OPERATOR’S MANUAL.
2. READ ALL SAFETY DECALS ON THE MACHINE.
3. CLEAR THE AREA OF OTHER PERSONS.
4. LEARN AND PRACTICE SAFE USE OF MACHINE CONTROLS IN A SAFE AND
CLEAR AREA BEFORE YOU OPERATE THIS MACHINE ON A JOB SITE.
It is your responsibility to observe pertinent laws and regulations and to follow manufac-
turer’s instructions on machine operation and maintenance.
See your Authorized Art’s-Way Manufacturing Co., Inc. dealer or
Art’s-Way Manufacturing Co., Inc. for additional operator’s manuals, illustrated parts cata-
logs, and service manuals.

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
TO THE OWNER 1
Congratulations on the purchase of your new Art’s-Way Manure Spreader. You have selected a top quality
machine that is designed and built with pride to ensure you have many years of efficient and reliable service.
Many people have worked on the design, production, and delivery of this Manure Spreader. The information
in this manual is based on the knowledge, study, and experience through years of specializing in the
manufacturing of farm machinery. This manual is designed to provide you with important information regarding
safety, maintenance, and machine operation so you can and will get the best possible performance from your
Manure Spreader.
Even if you are an experienced operator of this or similar equipment, we ask that you read this manual
before operating this Manure Spreader. The way you operate, adjust, and maintain this unit will have much
to do with its successful performance. Any further questions you may have about this product of Art’s-
Way equipment should be directed to your local Art’s-Way dealer or to Art’s-Way Manufacturing Co., Inc.
Armstrong, Iowa, 50514, [phone].
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE
Art’s-Way Manufacturing Co., Inc. is continually making product improvements. In doing so, we reserve
the right to make changes and/or add improvements to our products without obligation for the equipment
previously sold.
Modifications to this Manure Spreader may affect the performance, function, and safety of its operation.
Therefore, no modifications are to be made without the written permission of Art’s-Way Manufacturing Co., Inc.
Any modification made without the written permission of Art’s-Way Mfg. Co. Inc. shall void the warranty of this
product.
In the interest of continued safe operation of this Manure Spreader, pay particular attention to the safety alert
symbol(s) throughout this manual.
Art’s-Way Manufacturing Co., Inc. STATEMENT OF PRODUCT LIABILITY
Art’s-Way Manufacturing Co., Inc. recognizes its responsibility to provide customers with a safe and efficient
product. Art’s-Way Manufacturing Co., attempts to design and manufacture its products in accordance with
all accepted engineering practices effective at the date of design. This statement should not be interpreted
to mean that our products will protect against the user’s own carelessness or failure to follow common safety
practices nor will Art’s-Way Manufacturing Co., be liable for any such act. In addition, Art’s-Way Manufacturing
Co., assumes no liability for any altered product or any modified product by users or anyone other than an
authorized dealer.
IMPORTANT WARRANTY INFORMATION
The warranty for this Manure Spreader appears on page 6 of this manual. In order to establish proper warranty
registration, the Warranty Registration must be completed and returned to the factory. Failure to comply with
this requirement may result in reduced warranty allowances.
LIMITATIONS OF THIS MANUAL
This manual contains operating instructions for your V140 Manure Spreader only. Any mention of other
machinery in this manual other than the V140 Manure Spreader is for reference only. This manual does not
replace nor is it to be used for any machinery that may be attached to or used in conjunction with the V140
Manure Spreader.
TO THE OWNER

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
2 PARTS & SERVICE
As the purchaser of your new spreader, it is very important to consider the following factors:
A. Original Quality
B. Availability of Service Parts
C. Availability of Adequate Service Facilities
Art’s-Way Manufacturing Co., Inc. has an excellent dealership network ready to answer
any questions you may have about your spreader. Parts for your machine may be ordered
through our dealers. When placing a parts order, please have the model and serial number
ready. This will allow the dealer to fill your order as quickly as possible.
For your convenience, we have provided this space for you to record your model number,
serial number, and the date of purchase, as well as your dealer’s name and address.
PARTS & SERVICE
Serial and Model Number Placard

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
TABLE OF CONTENTS 3
TO THE OWNER 1
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE 1
Art’s-Way Manufacturing Co., Inc. STATEMENT OF PRODUCT LIABILITY 1
IMPORTANT WARRANTY INFORMATION 1
LIMITATIONS OF THIS MANUAL 1
PARTS & SERVICE 2
TABLE OF CONTENTS 3-5
LIMITED WARRANTY 6
SAFETY FIRST 7
NOTICES OF DANGER, WARNING, AND CAUTION 7
Safety Instructions 8
GENERAL 8
BEFORE OPERATING 9
DURING OPERATION 9
MAINTENANCE SAFETY 9
HYDRAULIC SAFETY 10
TRANSPORTATION SAFETY 10
STORAGE SAFETY 10
TIRE SAFETY 11
ASSEMBLY SAFETY 11
TABLE OF CONTENTS

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
4 TABLE OF CONTENTS
TABLE OF CONTENTS
NAME PAGE
~~~~~OPERATOR’S INSTRUCTIONS: MANURE SPREADER~~~~~ 13
~~~~~ILLUSTRATED PARTS LIST: MANURE SPREADER~~~~~ 27
HITCH ASSEMBLY 28
AXLE ASSEMBLY 30
SHIELD ASSEMBLY 32
DRIVELINE ASSEMBLY 34
FRONT PTO ASSEMBLY 36
REAR PTO ASSEMBLY 38
BEATERS ASSEMBLY 40
BEATER GEARS ASSEMBLY 42
SLOP-GATE ASSEMBLY 44
APRON CHAIN ASSEMBLY 46
APRON CHAIN ASSEMBLY (CONTINUED) 48
GEARBOX ASSEMBLY 50
APRON CHAIN HYDRAULICS ASSEMBLY 52
SLOP-GATE HYDRAULICS ASSEMBLY 54

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
TABLE OF CONTENTS 5

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
6 LIMITED WARRANTY
Art’s-Way Manufacturing Co., Inc. warrants the products it sells to be free from defects in
material and workmanship for a period of one (1) season after the date of delivery to the first
(original) purchaser, subject to the following conditions:
Art’s-Way Manufacturing Co., Inc. obligation and liability under this warranty is to repair
or replace (at the company’s option) any parts that upon manufacture were defective in
material or workmanship.
All parts and repairs under this warranty shall be supplied at Art’s-Way Manufacturing Co., Inc.
or an authorized Art’s-Way Manufacturing Co., Inc. dealer, at the option of
Art’s-Way Manufacturing Co., Inc.
Art’s-Way Manufacturing Co., Inc. warranty does not extend to parts and elements not
manufactured by Art’s-Way Manufacturing Co., Inc. and which carry the warranty of other
manufacturers.
Transportation or shipping to an authorized dealer for necessary repairs is at the expense
of the purchaser.
Art’s-Way Manufacturing Co., Inc. makes no other warranty expressed or implied and makes
no warranty of merchantability or fitness for any particular purpose beyond that expressly
stated in this warranty. Art’s-Way Manufacturing Co., Inc. liability is limited to the terms
set forth in this warranty and does not include any liability for direct, indirect, incidental or
consequential damages or expenses of delay and the company’s liability is limited to repair
or replacement of defective parts as set forth herein.
Any improper use and/or maintenance, including operation after discovery of defective
or worn parts, operation beyond the rated capacity, substitution of parts not approved by
Art’s-Way Manufacturing Co., Inc., or any alternation or repair by other than an authorized
Art’s-Way Manufacturing Co., Inc. dealer which affects the product materially and adversely,
shall void the warranty.
No dealer, employee or representative is authorized to change this warranty in any way or
grant any other warranty unless such change is made in writing and signed by an officer of
Art’s-Way Manufacturing Co., Inc.
Some states do not allow limitations on how long an implied warranty lasts or exclusions of,
or limitations on relief such as incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you the specific legal rights and you
may have other rights that vary from state to state.
LIMITED WARRANTY

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
SAFETY FIRST 7
SAFETY
INSTRUCTIONS
“A careful operator is the best insurance against an
accident.” Quote from the National Safety Council.
Most accidents can be prevented if the operator:
1. Fully understands how the machine functions.
2. Can anticipate situations which may produce
problems.
3. Can make necessary corrections before
problems develop.
THIS SYMBOL MEANS ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
- Universal Safety Alert Symbol
The American Society of Agricultural Engineers has
adopted the Universal Safety Alert Symbol as a way
to identify areas of potential danger if the equipment
is not operated correctly. Please be alert whenever
you see this symbol in the manuals or on your
spreader.
Art’s-Way Manufacturing Co., Inc. strives to make
our equipment as safe as possible. The Art’s-Way
V140 Manure Spreader conforms to applicable safety
standards at the time of manufacturing. A safety
conscious equipment operator makes an effective
accident-prevention program complete.
Safety features and instructions for the spreader
are detailed in the Safety Guidelines section of
this Operator’s Manual. It is the responsibility of
the owner to ensure that all operators read and
understand the manual before they are allowed to
operate the Spreader. (Occupational Safety and
Health Administration (OSHA) regulations 1928.57).
NOTICES OF DANGER, WARNING, AND CAUTION
Signal Words: Note the use of signal words DANGER,
WARNING, and CAUTION on the spreader and in
this manual. The appropriate signal word for each
has been selected using the following guidelines:
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
physical injury.
SAFETY
INSTRUCTIONS
Safety instructions (or equivalent) signs indicate
specific safety-related instructions or procedures.
Note: Contains additional information important
to a procedure and will be found within the
regular text body of this manual.
SAFETY FIRST

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
8 SAFETY INSTRUCTIONS
GENERAL
Most work related accidents are caused
by failure to observe basic safety rules
or precautions. An accident can often
be avoided by recognizing potentially
hazardous situations before an accident
occurs. As you operate and maintain the
Spreader you must be alert to potential
hazards. You should also have the
necessary training, skills, and tools to
perform any assembly procedure.
Improper operation and/or maintenance
of this unit could cause a dangerous
situation that results in injury or death.
Do not use this unit until you read and
understand the information contained in
this manual. Do not use this equipment
for anything other than its intended
purpose.
Safety precautions and warnings
are provided in this manual and on
the unit. If these hazard warnings
are not heeded, bodily injury or
death could occur to you or to other
persons.
Art’s-Way Manufacturing Co., Inc.
cannot anticipate every possible
circumstance that might involve
a potential hazard. The warnings
in this manual and on the product
are, therefore, not all-inclusive. If a
method of operation not specifically
recommended by us is used, you must
satisfy yourself that it is safe for you
and for others. You should also ensure
that the unit will not be damaged or be
made unsafe by the methods that you
choose.
The information, specifications, and
illustrations in this manual are based on
the information that was available at the
time this material was written and can
change at any time.
Safety Alert Symbols
This is the safety alert symbol. It
is used to alert you to potential
personal injury hazards. Obey all
safety messages that follow this
symbol to avoid possible injury or
death.
This manual contains DANGERS,
WARNINGS, CAUTIONS, NOTICES,
SAFETY INSTRUCTIONS, and NOTES
which must be followed to prevent the
possibility of improper service, damage to
the equipment, personal injury, or death.
The following key words call the readers
attention to potential hazards.
Hazards are identified by the “Safety
Alert Symbol” and followed by a signal
word such as “DANGER”, “WARNING”, or
“CAUTION”.
SAFETY
INSTRUCTIONS
Remember:
“The Best Operator is a Safe Opera-
tor”
CAUTION
Read and understand the opera-
tor’s manual and all the safety
decals before operating the
spreader. Review all safety instruc-
tions with all operators annually.
SAFETY INSTRUCTIONS

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
SAFETY INSTRUCTIONS 9
BEFORE OPERATING
SAFETY
INSTRUCTIONS
Do not wear loose fitting clothing as it may
catch in moving parts.
Make sure all guards and shields are
installed, including the tractor power take-
off (PTO) master shield, before starting or
operating the spreader.
OEM
Be sure that the correct implement driveline
parts are used and that they are properly
secured.
Lower the lifter wheels when the spreader is not
in use.
Installsafetychainwhenattachingthespreadertothe
tractor.
Clear the area of bystanders, especially
children, when making repairs, adjustments,
or performing maintenance on the spreader.
Do not allow riders.
Put all tractor and machine controls in “neutral”
and disengage the PTO before starting. Follow the
starting instructions according to the OEM tractor
manual.
Operate the spreader only while seated on
the tractor seat.
Make sure the unit is adequately supported
with safety blocks or safety stands when
changing tires or performing maintenance.
DURING OPERATION
CAUTION
STOP
Entanglement Hazard
Keep hands, feet, hair, and
clothing away from moving
parts. Wait for all movement to
stop before approaching equipment.
Before making adjustments:
1. Shut off the tractor,
2. Set parking brake,
3. Put machine in neutral, and
4. Remove key while making adjustments.
Keep all shields and guards in place and in
good working condition.
Keep all bystanders, especially children,
away from the spreader while in operation.
Do not allow riders while the spreader is in
operation.
Do not attempt to unclog, clean, or adjust
the spreader while it is running.
Stay away from overhead power lines.
Electrocution can occur even without direct
contact.
Keep all hydraulic lines, fittings, and
couplers tight and free of leaks. (Refer to
Safety Guidelines – Hydraulic Safety).
Use caution when ascending or descending
on the spreader. Wet shoes or boots are
slippery.
MAINTENANCE SAFETY
SAFETY
INSTRUCTIONS
Follow all operating, maintenance, and safety
instructions found in this Manual.
STOP
Before servicing, adjusting,
repairing, or unclogging the
machine, always make sure
the tractor engine is stopped,
key in your pocket, the machine is lowered to the
ground, all controls are placed in neutral, the
parking brake is set, and all the moving parts have
stopped.
Use sufficient tools, jacks, and hoists that
have the capacity for the job.
Use support blocks or safety stands when
changing tires or performing maintenance.
Follow good shop practices of
keeping the service area clean and
dry, and use adequate light for the
job at hand.
Before applying pressure to the hydraulic
system, make sure all lines, fittings, and
couplers are tightly secured and in good
condition.
Make sure all shields/guards are in place
and properly secured when performing
maintenance.

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
10 SAFETY INSTRUCTIONS
HYDRAULIC SAFETY
SAFETY
INSTRUCTIONS
Follow all operating, maintenance, and
safety instructions found in this Manu-
al.
Make sure components in
the hydraulic system are kept
clean and in good working condition.
0
Relieve pressure from the hydraulic system
before servicing or disconnecting from the
tractor.
Keep all hydraulic lines, fittings, and
couplers tightly secured and free of leaks.
Replace any worn, cut, abraded, flattened,
or crimped hoses.
Do not make any temporary repairs to the
hydraulic lines, fittings, or hoses using
tape, clamps, or cement. The hydraulic
system operates under extremely high
pressure and temporary repairs may fail suddenly
and create a hazardous/dangerous situation.
Wear proper hand and eye
protection when searching
for a high-pressure
hydraulic leak. Use a piece
of wood or cardboard as a backstop instead of
hands to identify and isolate a leak. If injured by a
concentrated high-pressure stream of hydraulic
fluid, seek medical attention immediately. Serious
infection or toxic reaction can develop if hydraulic
fluid penetrates the surface of the skin.
Before applying pressure to the system,
make sure all components are tight and
that the hydraulic lines, hoses, and
couplings are not damaged.
TRANSPORTATION SAFETY
SAFETY
INSTRUCTIONS
Follow all operating and safety instructions found in
this manual when transporting this equipment.
Make sure the spreader complies with all local
regulations regarding transporting equipment on
public roads and highways.
Make sure the Slow Moving Vehicle (SMV)
emblem and all lights and reflectors
required by local highway and transportation
authorities are properly in place, clean, and
clearly visible to traffic.
Do not allow riders on any machinery
during transport.
Make sure the spreader is securely attached to the
tractor and install a safety chain to the spreader.
Make sure the tractor brake pedals are latched
together.
Do not exceed 20 mph (32 km/h) when transporting
the spreader. Always reduce speed on rough roads
and surfaces, or when going down inclines.
Use caution when turning and always use the
turn signals on the tractor to indicate your turning
intentions to the other traffic.
The weight of the trailed machine should NEVER
exceed the weight of the towing vehicle.
Check all clearances carefully whenever the
machine is towed.
Lower the elevator into the transport position
before transporting the spreader on the highway .
Stay away from overhead obstructions and
power lines during transport. Electrocution
can occur even without direct contact.
STORAGE SAFETY
SAFETY
INSTRUCTIONS
Follow all operating and safety instructions found in
this manual when storing this equipment.
Store the spreader in an area away from
human activity.
Do not permit children to play on or around
the stored machine at any time.
Make sure that the spreader is stored in an area
with a firm and level base to prevent the machine
from tipping or sinking into the ground.
Block the wheels to prevent the machine
from rolling.

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
SAFETY INSTRUCTIONS 11
TIRE SAFETY
SAFETY
INSTRUCTIONS
Follow all operating and safety instruc-
tions found in this manual when work-
ing around tires.
Have only a qualified tire dealer or tire
repair service perform tire repairs.
Do not attempt to install a tire on a wheel or
rim unless you have the proper equipment
and experience to do the job.
Do not substitute tires with a lesser road
rating and/or capacity for the original
equipment tires.
WARNING
Explosive Force Hazard
Tire replacement, repair, and/or
maintenance should be done by
a qualied tire dealer or qualied repair
service.
Failure to follow proper procedures
when installing a tire on a wheel or rim
can produce an explosive force that
will result in serious injury or death.
Do not attempt to install a tire without
proper equipment and experience to
perform the job.
ASSEMBLY SAFETY
SAFETY
INSTRUCTIONS
Follow all assembly, operating, and
safety instructions found in this manu-
al when assembly this equipment.
Use adequate manpower to perform
assembly procedures safely.
Assemble the spreader in an area with
sufficient space to maneuver the largest
components and allow easy access to all
sides of the machine.
Use only forklifts, lift cranes, jacks,
and tools with sufficient capacity for
the loads.
Do not allow spectators, especially
children, in the working area.

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
12 SAFETY INSTRUCTIONS
THIS PAGE
LEFT
INTENTIONALLY
BLANK

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
OPERATOR’S INSTRUCTIONS: MANURE SPREADER 13
OPERATOR’S INSTRUCTIONS: MANURE SPREADER

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
14 OPERATOR’S INSTRUCTIONS: MANURE SPREADER

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
OPERATOR’S INSTRUCTIONS: MANURE SPREADER 15

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
16 OPERATOR’S INSTRUCTIONS: MANURE SPREADER

ART’S-WAY MANUFACTURING COMPANY, INC. Manual No. H610122
OPERATOR’S INSTRUCTIONS: MANURE SPREADER 17

Manual No. H610122 ART’S-WAY MANUFACTURING COMPANY, INC.
18 OPERATOR’S INSTRUCTIONS: MANURE SPREADER



   
