ARTECH S1 User manual

Wireless Service Bell S1

Contents
Structure of the Manual(This manual consists of following
sections)
Section 1 Installation ……………………………………1
I. System Specifications ……………………….....1
II. Packing and Accessories Instruction ………....2
III. System Connecting Diagram ……………….....5
Section 2 Main board Installation ……………..…......5
I. Main board Overview ………………………......5
II. Suspension Holder Installation ……………......6
III. Labeling Table Number Logo on Main
board…………………………. ……………….....8
IV. Main board Power Adaptor Installation ……....10
Section 3 Service Button Installation ……..…….…..10
I. Service Button Overview Introduction …….......10
II. Battery Installation ……………………………....10
III. Labeling Table Number Logo on Service
button ……………………………………………..11
IV. Service Button Stand Installation ……………...12
Section 4 Main board Configuration ……..……….….13
I. Main board Receiver DIP Switch Setting
Introduction ……………………………………....15
II. Ring Volume Setting ……………..……………....15
III. Ring Types Setting………………..……………....15
IV. Tie-in Key Model Setting……….………………….16
V. Ring Times Setting ……………………………….16
VI. System Receiving Range Setting ……………….16
Section 5 Service Button Configuration ………………17
I. Service Button DIP Switch Setting Instruction ….19
II. Service Button Table Number Setting …………..19
III. Service Button Transmitting Range Setting……..21
Section 6 System operating Instruction ……………….21
I. Service Requirements …………………………..…21
II. Canceling Service Method ………………………..22
Section 7 Daily Usage and Maintenance ……………….22
I. Daily Testing ……………………………….…..…..22
II. Usage Cautions …………………...…………..…..24

Section 1 Installation
Part I. System Specifications
S1 Wireless Service Bell Main board (S1)
Product Spec
Name: Wireless Service Bell Main board
Receiver
Model: S1
Dimension:
260(L) × 165(W) × 40(H) (mm)
Weight: 495g
Power Cable: 1.5M
Button
Service Button x 32 Units
LED Indicator
Receiving Indicator
Power Indicator
Message Indicator
Table Indicator x 32 Units
Environment
Requirements
AC100~240 Power Jack
Operating Temp 0°C - 50°C
(32°F - 122°F)
Operating Humidity 10% - 90% without
congealment
Electronic
Characteristic
Operating Voltage: DC5V
Operating Current: 200mA
Standby < 30Ma
Full Load < 35mA
Startup Current: 600mA
Speaker(Full duplex)
Impedance: 8Ω±15%
Max Output Power: 0.5W
Distortion Rate: 5%MAX
Max dB: 89 ±3dB
Frequency Range: 50Hz ~10KHz
Packing Contents
Contents:
Wireless Service Bell Receiver (S1)
User’s Manual
S1 Table no. Logo
1

2
Service Button Table no. Logo
Main board Receiver Location Map
Button Clamp
Logo Clamp
DC5V 1.5A Power Adaptor
Pen for Logo
Screwdriver
Main board Fixed Screws
S1 Wireless Service Button (AB100)
Product Spec
Name: Wireless Service Button
Model: AB100
Dimension:60(L) ×45(W) × 23(H)(mm)
Weight: 31g
Button
Service Button x 1 unit
Contents
Wireless Service Button (AB100)
Environment
Requirements
Operating Temp 0°C - 50°C
(32°F - 122°F)
Operating Humidity 10% - 90% without
congealment
Electronic
Characteristic
Operating Voltage: 12V Battery
Operating Current:Standby < 10mA
Working status < 10mA
Packing Contents
DC12V Battery
Screws
Multi Functional Service Button (AB400)
Product Spec
Name: Multi Functional Service
Button
Model: AB400
Dimension: 60(H) ×45(W)×
23(H)(mm)
Weight: 31g
Button
4 functional button
Environment
Requirement
Operating Temp:0°C - 50°C (32°F -
122°F)
Operating Humidity:10%- 90%
without congealment
Electronic
Characteristic
Operating Voltage: 12V Battery
Current: Idle < 10mA Working< 10mA
Package Content
Multi-functional button

3
Battery
Screw
Part II. Packing and Accessories Instruction
S1 Wireless Service Main board Receiver Packing
Contents:
S1 Main board Receiver
User’s Manual
Main board Fixed illustration
Main board Table
No. Logo Paster

4
Service Button Table
No. Logo Paster
Service Button Clamp
Logo Paster Tool
DC5V 1.5A
Power Adaptor
Logo Pen
Screwdriver
Main board Fixed Screw
Group X 3

5
AB100 Service Bell Button Packing Contents:
AB100 Service Bell Button
DC12V Battery
Screw
AB400 Multi-functional button：
AB400 Multi-functional
button
DC12V Battery
Screw
AS100 Service Bell Button Stand Packing Contents:
AS100 Plastic Stand
Part III. System Connecting Diagram

6
Wireless service bell provides real-time service for customers
and can economize waiters so thatcan enhance whole
appearance for the restaurant. Getting rid of landline designing
way to use wireless method, it can be installed very quickly and
can response receiving range around 50 meters, one wireless
service bell main board receiver can be matched max 32
service buttons and support 4 kinds of prompt voice for
selection.
Section 2 Main board Installation
Part I. Main board Overview
Please reading the manual first before using the wireless
service bell.
Part II. Suspension Holder Installation
Cautions: Please make sure don’t plug in power adapter for
Main board and
select

7
corresponding screws, please take care of the casing while
installing.
Accessories:
1. Take out main board fixed map and tear up back
lamination.
2. Stick main board map to place inwhichyou want with
horizontal level.
3. When installing to wall, please use 6Φmm tool to
make holes, for more details please refer to picture

8
display hole.
4. After making holes ok, please insert plastic cushion
to hole.
5. You can use a tool to insert plastic cushion.
6. Take out screws and insert to the plastic cushion for
fixing and leave 7mm outside.
7. Dismantle main board fixed map.

9
8. Fix main board tothe wall according to its behind
instruction.
Part III. Labeling Table Number Logo on Main board
S1 wireless service bell attached with below accessories(if there
need make a logo for special tablecan be made by pen on the
blank paper).
Attached Accessories:

10
1. Take out tool for dismantling button according to
picture indication to dismantle button.
2. Take out table number logo(small font), then sticking
to button location.
3. Then install button casing back on the main board.
4. Then labeling Logo is finished on main board.

11
Part IV. Main board Power Adaptor Installation
Cautions: Please don’t use other power adaptor to avoid
working not properly.
1. Take out attached power adaptor (Input AC100-240V
output DC5V)andconnecting it like following
diagram.
2. Please plug in power adaptor to wall power socket
will light in a power Indicator. Then plug in another
power adaptor terminal to S1 main board will light in a
Indicator on main board.
Section 3 Service Button Installation
Part I. Service Button Overview Introduction
Part II. Battery Installation
Cautions: Please using attached screw and screwdriver to
install.
Please make sure battery direction(+/-) is right way.
Accessories:

12
1. Take out attached battery(DC12V) and installing it
according to its polarity.
2. Close battery cover while installing ok.
3. Take out screwdriver to install screw to end
procedure.
Part III. Labeling Table Number Logo on Service button
S1 wirelessservice button attached with logo paper (if need use
for a special table number can be written by a pen on a blank
paper).
Accessories:

13
1. Take out logo for table number (Font is more bigger)
and install it according to the picture indication.
2. Then labeling Logo is ok as shown in below picture.
Part IV. Service Button Stand Installation
Cautions: Please using attached screw and screwdriver to
install.
Accessories:
1. Take out screwdriver to dismantle screw on service
button according to picture indication.

14
2. Install service button on plastic stand like below
operating way.
3. Install screw to fix the button by screwdriver like below
operating way.
Section 4 Main board Configuration
Cautions: Wirelessservice bell main board has 2 switches, one
is normal DIP switch, another one is 3-status switch.
Accessories:
1. Take out screwdriver to dismantle screw on main
board.

15
2. Open up switch cover on main board.
3. According to system configuration to set DIP switch
by clamp.
4. After setting ok to close switch cover.
5. Then install screw by screwdriver to end procedure.

16
Part I. Main board Receiver DIP Switch Setting Introduction
1. Open up main board receiver willshow 2 switches
like following.One is normal DIP-2 switch, another
one is threestatus DIP-3 switch and a twist switch for
ring volume adjustment.
2. A switch is used for ring volume adjustment
3. B switch is normal DIP-2 switch
4. C 、D group switch are DIP-3 three status switch
5. Each switch functionality definition as follows:
A Group: Used for ring volume adjustment
B Group: Used for ring types selection
C Group(1、2、3、4、5、6): Set system receiving range
D Group(7): Button type
E Group(8): Number of alert tone
(Cautions: After changing C&D switch position need
restart to plug power adaptor tovalidate settings)
Part II. Ring Volume Setting
A switch is used for ring volume adjustment.
When adjust to “—“ position to turn down volume
When adjust to “＋” position to turn up volume
Part III. Ring Types Setting
B group switch is used to set ring types
When 1to ON & 2、3、4 to OFF status: Ring type 1
When 2 to ON & 1、3、4 to OFF status: Ring type 2
When 3 to ON & 1、2、4 to OFF status: Ring type 3
When 4 to ON & 1、2、3 to OFF status: Ring type 4