Asahi KASEI Sensair aSENSE VAV User manual

Installation Manual
aSENSE VAV
Dismounting of the sensor
Pull the top part upwards
Push the front part with the lid upwards Fold the front part with the lid forwards
while keeping the wall plate steady and loose it from the hooks (#1)
4
32
6
15
1
1 Top part
2 Lid
3 Front part
4 Wall plate
5 Screw
6 Label with
settings inside the
top part

Mounting of the sensor
The wall plate is screwed onto the wall (A) Put the top tabs of the front part into the top
holes of the wall plate. (B) Press the lower edge of the case onto
the wall plate to latch
The top part is pushed under the Terminals and jumpers on aSENSE VAV.
locking hooks of the wall plate The darker positions are default settings.
and is secured with a screw. Terminals and jumpers are located under the top part.
NOTE!
If for some reason the PCB must be removed it must be handed carefully and protected from
electrostatic discharge! Normally, removing the PCB is not required.
A
B
~
+
Screw head diameter: max 7.5 mm
Screw head height: max 2.5 mm

Electrical connections
The power supply has to be connected to and . is considered as system ground. The
same ground reference has to be used for the aSENSE VAV unit and for any connected device! Unless
different transformers are used, special precautions need to be taken.
NOTE!
The signal ground is not galvanically separated from the aSENSE VAV power supply!
NOTE!
The same ground reference has to be used for the aSENSE VAV unit and for any connected device!
If possible keep the sensor powered up after mounting. Connect the analogue output before
measuring.
Connection
Terminal
Function
Electrical Data
Remarks
Power (+)
Power ground (-)
24 VAC/DC+ (+-20%), 3W
24 VAC/DC-
2W without output load
See note 1!
Out(1)
Out(2)
5
Analogue Output 1 (+)
Analogue Output 2 (+)
Signal Ground (-)
0─10 VDC or 0─20 mA,
2─10 VDC or 4─20 mA,
Same as Output 1
Connected to via PTC
fuse
According to positions of
Out(1) jumper and start
point selection. See note 2!
According to positions of
Out(2) jumper and start
point selection. See note 2!
See note 1!
6
7
Normally open relay
Contact free relay
minimum load 1mA/5V
rated load 0.5A/125VAC;
1A/24VDC
Triggered by register Out(3)
8
Out(4)
Analogue Output 4 (+)
or Open Collector
0-10 VDC
Max 0.5A, 55VDC / 40VAC
(half-wave rectifier protection)
According to positions of
Out(4).
See note 2 and 3!
DI1
DI1
Digital Input 1
Closed contact current 1mA
Open contact voltage max 5V
Do not apply any voltage
on this input!
Table I. Electrical terminal connections for aSENSE VAV
Note 1: The ground terminal is used as negative power supply DC input or AC phase ground
(half wave rectifier). The signal ground M, protected by a PTC resistor, is the same as power ground
(permitting a ”3-wire” configuration). A single transformer may be used for the entire system.
Note 2: aSENSE VAV can deliver both a voltage or a current loop for Out(1) / Out(2). For Out(4) a
voltage output or an open collector output is selected with jumper OUT4. To change between voltage
and current output mode the hardware jumpers are used. There is one jumper for Out(1) and one for
Out(2), so that one output can be a voltage output and the other a current output. Both, voltage output
and current output, can have start points 0 % (0─10 VDC or 0─20mA) or 20% (2─10 VDC or
4─20mA) selected from PC software.
Note 3: Current of Open Collector is internally returned to terminal.
+
~
+
~

Dimensions and holes
Dimensions of sensor in mm and (inches)
Mounting of the sensor onto the wall
Screw head diameter: max 7.5 mm
Screw head height: max 2.5 mm
Dimensions of mounting plate in mm and (inches)
120(4,72)
31(1,22)
83(3,26)
29,8(1,17)
30(1,18)
7,8(0,31)
4,2(0,16)
2(0,08)
52,5(2,07)
30(1,18)
25(0,98)
30(1,18)
SenseAir®AB (headquarter)
Stationsgatan 12 Phone: +46-(0)653 - 71 77 70
Box 96 E-mail: [e-mail]
824 08 Delsbo
SWEDEN Web site: www.senseair.com