ASROCK iBOX 1200 Series User manual

iBOX 1200 Series
User Manual
Version 1.0
Published June 2022

Version 1.0
Published November 2022
Copyright©2022 ASRock Inc. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock’s Website: www.ASRock.com

Replaceable batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
CAUTION (or Warning)
Hot surface
Do not touch
e equipment intended only for use in a Restricted Access Area.
DIN Rail/Wall Mount: M3x5mm Screws (for securing the mounting bracket(s) to the chassis)
VESA Mount: M4x6mm Screws (for securing the VESA bracket to the monitor)
is product should be connected by means of a power cord to a socket-outlet
with earthing connection.
e terms HDMI®and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at www.ASRock.com; or you may contact your dealer for
further information.
ASRock Incorporation
6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)

Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Product Specications 2
Chapter 2 Product Overview 4
2.1 Front View 4
2.2 Rear View 5
2.3 Inside View 6
Chapter 3 Hardware Installation 7
3.1 How to Remove the Bottom Case 7
3.2 How to Install the WiFi Module 8
3.3 How to Remove the M.2 SSD and the Bracket 9
3.4 How to Install the M.2 SSD 10
3.5 How to Install the 2.5-inch Hard Drive 11
3.6 How to Install the Memory Modules (DDR4) 14
3.7 How to Install the VESA Bracket 15
3.8 How to Install the Wall Mounting Brackets 17
3.9 How to Install the Din Rail Mounting Bracket (Optional) 19
Chapter 4 Motherboard 20
4.1 Motherboard Layout 20
4.2 Motherboard Specications 21
4.3 Onboard Headers and Connectors 23
4.4 Installation of ROM Socket 26
4.5 Expansion Slots (M.2 Slots) 27

Chapter 5 UEFI Setup Utility 28
5.1 Introduction 28
5.1.1 UEFI Menu Bar 28
5.1.2 Navigation Keys 29
5.2 Main Screen 29
5.3 Advanced Screen 30
5.3.1 CPU Conguration 31
5.3.2 Chipset Conguration 33
5.3.3 Storage Conguration 34
5.3.4 Super IO Conguration 35
5.3.5 AMT Conguration 36
5.3.6 ACPI Conguration 38
5.3.7 USB Conguration 39
5.3.8 Trusted Computing 40
5.4 Hardware Health Event Monitoring Screen 41
5.5 Security Screen 42
5.6 Boot Screen 43
5.7 Exit Screen 44
Chapter 6 Software Support 45
6.1 Install Operating System 45

iBOX 1200 Series
8 1
English
Chapter 1 Introduction
1.1 Package Contents
• iBOX-1200 Series
• 1 x SATA 1 to 1 Power Cable
• 4 x HDD Screws (M3x4)
• 1 x WiFi Module Screw
• 1 x Screw for M.2 slot
• 1 x Bracket for M.2 2280 support
• 1 x 19V/90W Power Adapter
• 1 x VESA Mount Bracket & Screw Package (by request)
• Din Rail Kit & Screw Package (by request)
• Wall Mount Kit & Screw Package
• Support CD
• Quick Installation Guide
Because the hardware specications might be updated, the content of this documentation
will be subject to change without notice.
If any items are missing or appear damaged, contact your authorized dealer.

2 3
English
1.2 Product Specications
Memory
Technology
Capacity
Socket
Dual Channel DDR4 3200 MHz
64GB (32 GB perDIMM)
2 x 260-pin SO-DIMM
Graphics
Controller
HDMI
DisplayPort
MultiDisplay
Intel® Iris®XeGraphics for i7/i5 CPU
Intel®UHD Graphics for i3/Celeron CPU
HDMI 2.0b
Max resolution up to 4096x2160@60Hz
DisplayPort 1.4a, DP++
Max resolution up to 4096x2160@60Hz
Quad-Display (Included 2 outputs from Type-C)
Processor System
CPU
Chipset
BIOS
iBOX-1265UE( i7-1265UE)
iBOX-1245UE( i5-1245UE)
iBOX-1215UE( i3-1215UE)
MCP
AMI SPI 256 Mbit
Audio
Interface Realtek ALC233, High Definition Audio.
Ethernet
Controller/ Speed
Connector
iBOX-1265UE/ iBOX-1245UE:
Intel®I225LM with 10/100/1000/2500 Mbps, supports AMT/vPro
iBOX-1215UE :
Intel®I225LM with 10/100/1000/2500 Mbps
2 x RJ-45
Expansion Slot
M.2 1x M.2 (Key E, 2230) with PCIe x1, USB 2.0 and CNVifor Wireless
Storage
M.2
SATA
1 x M.2 (KeyM, 2242/2260/2280) with PCIe Gen4 x4 for SSD
*M.2 Key M 2280(Supported by bracket)
1 x SATA3.0 (6.0 Gb/s)
Front I/O
USB
Audio
2 x USB 3.2 Gen2 (Type A),2 x USB 2.0
2 x USB 3.2 Gen2 (Type-C, Supports DP1.4a display output)
* USB4™ Compliance Test is pending for certification
2 x USB 2.0
1 (headphone& microphone jack)

iBOX 1200 Series
2 3
English
Environment
Operating Temp
Storage Temp
Operating Humidity
Storage Humidity
0ºC ~ 40ºC
-40° C– 85° C
5% ~ 90%
5% ~ 90%
Mechanical
Construction
Mounting
Dimensions (W x H x D)
Weight
Aluminum
VESA mounting, Wall mounting, Din-rail (By request)
171.8 x 50.05 x 109.45 mm
Net Weight:1.6Kg
Watchdog Timer
Output
Interval
From Super I/O todrag RESETCON#
256 Segments,0,1,2, ...255sec
Power Requirements
Input PWR
Power On
12V~19V DC-In Jack
AT/ATX Supported
- AT : Directly PWR on as power input ready
- ATX :Press button to PWR on after power input ready
Rear I/O
HDMI
DisplayPort
Ethernet
USB
DC Jack
COM
1 x HDMI 2.0b
1 x DP1.4a
1 x 1 Gigabit LAN,1 x 2.5 Gigabit LAN
2 x USB 3.2 Gen2 (Type-A)
1
1 x COM(RS-232)
Others
OS Support
TPM
Certifications
Packing List
Windows 10/11
TPM 2.0 onboard IC
CE, FCC Class A
1 x 19V/90W Power Adapter
1 x Screw Package
1 x Wall mount kit
1 x Bracket for M.2 2280 support

4 5
English
Chapter 2 Product Overview
is chapter provides diagrams showing the location of important components of
the iBOX V2000 / iBOX 1100 Series.
2.1 Front View
No. Description
1Audio(Mic-in, Line-out)
2 2 x USB 3.2 Gen2 Ports (Type C, supports DP1.2a display output)
3 USB 3.2 Gen2 (Type A)
4 USB 2.0 (Type A)
1 2
34

iBOX 1200 Series
4 5
English
2.2 Rear View
No. Description
1COM Port
2 Power Button
3 2 x USB 3.2 Gen2 Ports (Type A)
4HDMI
5 RJ-45 (2.5G LAN)
6DC-IN
7DisplayPort
8 RJ-45 (2.5G LAN)
*ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps/1Gbps
connection
On Link Green 2.5Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
23
145
678

6 7
English
2.3 Inside View
No. Description
1SO-DIMM Slots
2 SATA 3.0 Connector
3 M.2 Slot (Key M)
4 M.2 Slot (Key E)
5 Hard disk drive tray (compatible with 2.5" SATA HDD/SSD)
SO-DIMM memory, hard drive and mSATA SSD are not included with this system.
1
3
2
4
5
D

iBOX 1200 Series
6 7
English
Chapter 3 Hardware Installation
is chapter helps you install or remove important components.
3.1 How to Remove the Bottom Case
1. Remove the four screws on the bottom case.
2. en li up and remove the bottom panel.
1
2

8 9
English
3.2 How to Install the WiFi Module
1. Locate the WiFi Module slot on the motherboard.
2. Carefully insert the WiFi Module into the slot.
3. Tighten the screw to secure the WiFi Module to the motherboard.

iBOX 1200 Series
8 9
English
3.3 How to Remove the M.2 SSD and the Bracket
1. Release the screw and carefully remove the M.2 SSD.
2. Release the screw and remove the bracket from the motherboard.

10 11
English
3.4 How to Install the M.2 SSD
1. Locate the M.2 slot on the motherboard.
2. Carefully insert the M.2 SSD into the slot.
3. Tighten the screw to secure the M.2 SSD to the motherboard.

iBOX 1200 Series
10 11
English
3.5 How to Install the 2.5-inch Hard Drive
1. Remove the four screws on the bottom case. en li up and remove the bottom panel.
2. Attach the HDD cage to the bottom panel and secure it using the four screws. en
connect the SATA cable to the HDD.

12 13
English
3. Connect the SATA Data and Power Cable to the HDD.
4. Connect the SATA Cable to the connector.

iBOX 1200 Series
12 13
English
5. en reinstall the bottom panel.

14 15
English
3.6 How to Install the Memory Modules
(DDR4)
1. Carefully insert the SO-DIMM memory modules into the slot at a 30-degree angle.
2. Push down until the modules snap into place.
1. e iBOX V2000 / iBOX 1100 Series requires DDR4 SO-DIMM.
2. For dual channel conguration, you always need to install identical (the same brand,
speed, size and chip-type) DDR4 SO-DIMM pairs.
e SO-DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.