ASROCK N68C-GS4 FX User manual

11
11
1
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
Copyright Notice:Copyright Notice:
Copyright Notice:Copyright Notice:
Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans-
lated in any language, in any form or by any means, except duplication of documen-
tation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identifica-
tion or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:Disclaimer:
Disclaimer:
Specifications and information contained in this guide are furnished for informational
use only and subject to change without notice, and should not be constructed as a
commitment by ASRock. ASRock assumes no responsibility for any errors or omissions
that may appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or
conditions of merchantability or fitness for a particular purpose. In no event shall
ASRock, its directors, officers, employees, or agents be liable for any indirect, special,
incidental, or consequential damages (including damages for loss of profits, loss of
business, loss of data, interruption of business and the like), even if ASRock has been
advised of the possibility of such damages arising from any defect or error in the guide
or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Published October 2013
Copyright©2013ASRock INC.All rights reserved.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com

22
22
2ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
Motherboard LayoutMotherboard Layout
Motherboard LayoutMotherboard Layout
Motherboard Layout
1 CPU Fan Connector (CPU_FAN1) 11 USB 2.0 Header (USB8_9)
2 ATX 12V Power Connector (ATX12V1) 12 USB 2.0 Header (USB6_7)
3 2 x 240-pin DDR2 DIMM Slots 13 USB 2.0 Header (USB4_5)
(Dual Channel: DDRII_1, DDRII_2; Yellow) 14 Chassis Speaker Header (SPEAKER1)
4 2 x 240-pin DDR3 DIMM Slots 15 Chassis Fan Connector (CHA_FAN1)
(Dual Channel: DDR3_A1, DDR3_B1; Black) 16 System Panel Header (PANEL1)
5 ATX Power Connector (ATXPWR1) 17 Clear CMOS Jumper (CLRCMOS1)
6 Primary IDE Connector (IDE1) 18 Print Port Header (LPT1)
7 SATA2 Connector (SATAII_1 (PORT 0.0)) 19 Floppy Connector (FLOPPY1)
8 SATA2 Connector (SATAII_3 (PORT 1.0)) 20 Power Fan Connector (PWR_FAN1)
9 SATA2 Connector (SATAII_4 (PORT 1.1)) 21 Chassis Intrusion Header (CI1)
10 SATA2 Connector (SATAII_2 (PORT 0.1)) 22 Front Panel Audio Header (HD_AUDIO1)
NVIDIA
GeForce
7025 /
nForce
630a
FSB800
DDRII_1 (64 bit, 240-pin module)
DDR3_A1 (64 bit, 240-pin module)
IDE1
SATAII_1
SATAII_2 SATAII_4
(PORT 0.0)
(PORT 0.1) (PORT 1.1)
SATAII_3 (PORT 1.0)
CHA_FAN1
SPEAKER1
1
HDLED RESET
PLED PWRBTN
1
PANEL 1
11
ATXPWR1
8Mb
BIOS
CMOS
BATTERY
CLRCMOS1
CPU_FAN1
ATX12V1
1
USB4_5
SOCKET AM2/AM3/AM3+
FSB800
DDRII_2 (64 bit, 240-pin module)
DDR3_B1 (64 bit, 240-pin module)
1
USB6_7
1
USB8_9
HD_AUDIO1
1
FLOPPY1
LAN
PHY
AUDIO
CODEC
Super
I/O
PCIE1
PCIE2
PCI1
PCI2
PWR_FAN1
RoHS
USB 2.0
T: USB0
B: USB1
Top:
RJ-45
Top:
LINE IN
Center:
FRONT
Bottom:
MIC IN
PS2
Mouse
PS2
Keyboard
VGA1
USB 2.0
T: USB2
B: USB3
COM1
1
LPT1
X Fast RAM
X Fast LAN
X Fast USB
1
CI1
1

33
33
3
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
I/O PI/O P
I/O PI/O P
I/O Panelanel
anelanel
anel
1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)
* 2 RJ-45 Port 7 USB 2.0 Ports (USB23)
3 Line In (Light Blue) 8 D-Sub Port
4 Front Speaker (Lime) 9 COM Port
5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)
12
6
7
4
3
5
8
910
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
Activity/Link LED SPEEDLED
Status Description Status Description
Off No Activity N68C-GS4 FX:
Blinking Data Activity Off 10Mbps connection
Orange 100Mbps connection
Green 1Gbps connection
N68C-S4 FX:
Off 10Mbps connection
Orange 100Mbps connection
LAN Port
ACT/LINK
LED SPEED LED

44
44
4ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows®XP:
After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer
ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or
“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDAAudio 2nd output” to use front panel audio. Then
reboot your system.
For Windows®8 / 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the
system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device
advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on
your system. Please follow below instructions according to the OS you install.
For Windows®XP OS:
Please click “VIA HDAudio Deck” icon , and click “Speaker”. Then you are allowed to
select “2 Channel” or “4 Channel”. Click “Power” to save your change.
For Windows®8 / 7 / VistaTM OS:
Please click “VIA HDAudio Deck” icon , and click “Advanced Options” on the left side
on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click
“OK” to save your change.
For Realtek ALC662 Audio Codec:
For VIA®VT1705 Audio Codec:

55
55
5
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction
Thank you for purchasing ASRock N68C-GS4 FX /N68C-S4 FX motherboard, a reliable
motherboard produced underASRock’s consistently stringent quality control. It delivers
excellent performance with robust design conforming toASRock’s commitment to qual-
ity and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step
guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to
BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might
be updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp
1.11.1
1.11.1
1.1 PP
PP
Packack
ackack
ackage Contentsage Contents
age Contentsage Contents
age Contents
OneASRock N68C-GS4 FX / N68C-S4 FX Motherboard (MicroATX Form Factor)
One ASRock N68C-GS4 FX / N68C-S4 FX Quick Installation Guide
OneASRock N68C-GS4 FX / N68C-S4 FX Support CD
Two SerialATA(SATA) Data Cables (Optional)
One I/O Panel Shield

66
66
6ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
1.2 Specifications1.2 Specifications
1.2 Specifications1.2 Specifications
1.2 Specifications
Platform - MicroATX Form Factor
A-Style - Home Cloud (N68C-GS4 FX)
CPU - Support for Socket AM3+ processors
- Support forAM3 processors:AMDPhenomTM II X6 / X4 / X3 /
X2 (except 920 / 940) / Athlon II X4 / X3 / X2 / Sempron
processors (see CAUTION 1)
- Support for SocketAM2+ / AM2 processors:AMD PhenomTM
FX / Phenom /Athlon 64 FX /Athlon 64 X2 Dual-Core /Athlon
X2 Dual-Core /Athlon 64 / Sempronprocessor
- Supports 8-Core CPU
- Supports UCC feature (Unlock CPU Core) (see CAUTION 2)
- Supports AMD’s Cool ‘n’ QuietTM Technology
- FSB 1000 MHz (2.0GT/s)
- Supports Untied Overclocking Technology
- Supports Hyper-TransportTechnology
Chipset - NVIDIA®GeForce 7025 / nForce 630a
Memory -Dual ChannelDDR3/DDR2 Memory Technology
- 2 xDDR3 DIMM slots
- SupportDDR3 1600/1333/1066 non-ECC, un-buffered memory
(see CAUTION 3)
- Max. capacity of system memory: 16GB (see CAUTION 4)
- 2 xDDR2 DIMM slots
-SupportDDR21066/800/667/533non-ECC,un-bufferedmemory
(see CAUTION 5)
- Max. capacity of system memory: 8GB (see CAUTION 4)
Expansion Slot - 1 x PCI Express x16 slot
- 1 x PCI Express x1 slot
- 2 x PCI slots
Graphics - IntegratedNVIDIA®GeForce 7025 graphics
- DX9.0 VGA, Pixel Shader 3.0
- Max. shared memory 256MB
- SupportsD-Sub with max. resolution up to 1920x1440
@ 60Hz
Audio - 5.1 CH HDAudio (RealtekALC662 / VIA®VT1705Audio Codec)
LAN N68C-GS4FX:
- Qualcomm®Atheros®AR8171, speed 10/100/1000 Mb/s
- Supports Qualcomm®Atheros®Security Wake On Internet
Technology
- Supports Wake-On-LAN

77
77
7
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
- Supports Energy Efficient Ethernet 802.3az
- Supports PXE
N68C-S4FX:
-Atheros®AR8152, speed 10/100 Mb/s
- Supports Wake-On-LAN
- Supports PXE
Rear Panel I/O I/O Panel
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x VGA Port
- 4 x USB 2.0 Ports
- 1 x RJ-45 LANPort with LED (ACT/LINK LEDand SPEEDLED)
- HDAudio Jack: Line in / Front Speaker / Microphone
Storage - 4 x SATA2 3.0Gb/s connectors, support RAID(RAID0, RAID1,
RAID0+1, RAID 5, JBOD),NCQ and Hot Plug
Connector - 1 xATA133 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x Print port header
- 1 x Chassis intrusion header
- 1 x CPU Fan connector (4-pin)
- 1 x Chassis Fan connector (3-pin)
- 1 x Power Fan connector (3-pin)
- 1 x 24 pinATX power connector
- 1 x 4 pin 12V power connector
- 1 x Front panel audio header
- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
BIOS Feature - 8MbAMI Legal BIOS
- Supports “Plug and Play”
-ACPI 1.1 Compliant Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- CPU, VCCM, NB Voltage Multi-adjustment
Support CD -Drivers, Utilities, AntiVirus Software (Trial Version),Google
Chrome Browser and Toolbar, Start8 (30 days trial)
Hardware - CPU Temperature Sensing
Monitor - Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- CASE OPEN detection
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

88
88
8ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
CAUTION!
1. This motherboard supports CPU up to 95W. Please refer to our website for
CPU support list. ASRock website http://www.asrock.com
2. UCC (Unlock CPU Core) feature simplifies AMD CPU activation. As long as
a simple switch of the BIOS option “ASrock UCC”, you can unlock the extra
CPU core to enjoy an instant performance boost. When UCC feature is
enabled, the dual-core or triple-core CPU will boost to the quad-core CPU,
and some CPU, including quad-core CPU, can also increase L3 cache size
up to 6MB, which means you can enjoy the upgrade CPU performance with
a better price. Please be noted that UCC feature is supported with AM2+ /
AM3 / AM3+ CPU only, and in addition, not every AM2+ /AM3 / AM3+ CPU can
support this function because some CPU’s hidden core may be
malfunctioned.
3. Whether 1600MHz memory speed is supported depends on the AM3/
AM3+ CPU you adopt. If you want to adopt DDR3 1600 memory module
on this motherboard, please refer to the memory support list on our
website for the compatible memory modules.
ASRock website http://www.asrock.com
4. Due to the operating system limitation, the actual memory size may be
less than 4GB for the reservation for system usage under Windows®8
/ 7 / VistaTM / XP. For Windows®OS with 64-bit CPU, there is no such
limitation.
5. Whether 1066MHz memory speed is supported depends on the AM2+
/ AM3 CPU you adopt. If you want to adopt DDR2 1066 memory module
on this motherboard, please refer to the memory support list on our
website for the compatible memory modules.
ASRock website http://www.asrock.com
6. This motherboard does not support RAID mode under Windows®8.1
32-bit / 8.1 64-bit.
WARNING
Please realize that there is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
the third-party overclocking tools. Overclocking may affect your system stability, or
even cause damage to the components and devices of your system. It should be
done at your own risk and expense. We are not responsible for possible damage
caused by overclocking.
OS - Microsoft®Windows®8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-bit
/ 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP 32-bit /
XP 64-bit (see CAUTION 6)
Certifications - FCC, CE, WHQL
- ErP/EuP ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com

99
99
9
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
1.3 Pin Header Easy Installation Guide1.3 Pin Header Easy Installation Guide
1.3 Pin Header Easy Installation Guide1.3 Pin Header Easy Installation Guide
1.3 Pin Header Easy Installation Guide
ASRock motherboard is equipped with pin headers with obvious colors which indicate
you to recognize the crucial headers more easily. Please refer to below illustrations for
the pin definition of onboard headers. If you want to have more information about the
usage of these headers, please refer to “Jumpers Setup“ and “Onboard Headers and
Connectors“ for details.
1
GND
PRESENCE#
MIC_RET
MIC2_L
MIC2_R
OUT2_R
J_SENSE
OUT2_L
OUT_RET
Front Panel Audio Header
1
PLED+
PLED-
PWRBTN#
HDLED+
HDLED-
GND
REST#
GND
DUMMY
System Panel Header
1
USB_PWR
P- P+
USB_PWR
P-
P+
GND
GND
DUMMY
Chassis Speaker Header
1
+5V
DUMMY
SPEAKER
DUMMY
USB 2.0 Header

1010
1010
10 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
1.4 Jumpers Setup1.4 Jumpers Setup
1.4 Jumpers Setup1.4 Jumpers Setup
1.4 Jumpers Setup
The illustration shows how jumpers are setup.
When the jumper cap is placed on pins, the
jumper is “Short”. If no jumper cap is placed on
pins, the jumper is “Open”. The illustration
shows a 3-pin jumper whose pin1 and
pin2 are “Short” when jumper cap is placed on
these 2 pins.
Jumper Setting
Clear CMOS Jumper
(CLRCMOS1)
(see p.2, No. 17)
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power supply.
Afterwaitingfor15seconds,useajumper cap toshortpin2andpin3 onCLRCMOS1
for 5 seconds. However, please do not clear the CMOS right
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
Clear CMOS
2_3 1_2
Default
If you clear the CMOS, the case open may be detected. Please adjust the
BIOS option “Clear Status” to clear the record of previous chassis intrusion
status.

1111
1111
11
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
FLOPPY1
Pin1
the red-striped side to
Pin1
1.5 Onboard Headers and Connectors1.5 Onboard Headers and Connectors
1.5 Onboard Headers and Connectors1.5 Onboard Headers and Connectors
1.5 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper
caps over the headers and connectors will cause permanent dam-
age of the motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.2 No. 19)
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector
(39-pin IDE1, see p.2 No. 6)
Note: Please refer to the instruction of your IDE device vendor for the details.
SerialATA2 Connectors These four SerialATA2 (SATA2)
(SATAII_1 (PORT 0.0): connectors support SATA2
see p.2, No. 7) or SATAhard disk for internal
(SATAII_2 (PORT 0.1): storage devices. The current
see p.2, No. 10) SATA2 interface allows up to
(SATAII_3 (PORT 1.0): 3.0Gb/s data transfer rate.
see p.2, No. 8)
(SATAII_4 (PORT 1.1):
see p.2, No. 9)
connect the black end
to the IDE devices
connect the blue end
to the motherboard
IDE1
PIN1
80-conductorATA 66/100/133 cable
SATAII_1 SATAII_3
(PORT 0.0) (PORT 1.0)
SATAII_2 SATAII_4
(PORT 0.1) (PORT 1.1)

1212
1212
12 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
USB 2.0 Headers Besides four default USB 2.0
(9-pin USB4_5) ports on the I/O panel, there are
(see p.2 No. 13) three USB 2.0 headers on this
motherboard. Each USB 2.0
header can support two USB
2.0 ports.
(9-pin USB6_7)
(see p.2 No. 12)
(9-pin USB8_9)
(see p.2 No. 11)
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
Front PanelAudio Header This is an interface for the front
(9-pin HD_AUDIO1) panel audio cable that allows
(see p.2, No. 22) convenient connection and
control of audio devices.
Print Port Header This is an interface for print
(25-pin LPT1) port cable that allows
(see p.2 No. 18) convenient connection of printer
devices.
1
AFD#
ERROR#
PINIT# GND
SLIN#
STB#
SPD0
SPD1
SPD2
SPD3
SPD4
SPD5
SPD6
SPD7
ACK#
BUSY
PE
SLCT
1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
USB_PWR
USB_PWR
P+5
P-5
P+4
P-4
GND
GND
DUMMY
1
USB_PWR
USB_PWR
P+7
P-7
P+6
P-6
GND
GND
DUMMY
1
1
USB_PWR
P-8
GND
DUMMY
USB_PWR
P+8
GND
P-9 P+9

1313
1313
13
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
ATX PowerConnector Please connect anATX power
(24-pin ATXPWR1) supply to this connector.
(see p.2 No. 5)
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
3-Pin Fan Installation
Pin 1-3 Connected
20-Pin ATX Power Supply Installation
Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
12
1
24
13
12
1
24
13
+5V
DUMMY
DUMMY
SPEAKER
1
GND
PWRBTN#
PLED-
PLED+
DUMMY
RESET#
GND
HDLED+
HDLED-
1
System Panel Header This header accommodates
(9-pin PANEL1) several system front panel
(see p.2 No. 16) functions.
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1) speaker to this header.
(see p.2 No. 14)
Chassis and Power Fan Connectors Please connect the fan cables
(3-pin CHA_FAN1) to the fan connectors and
(see p.2 No. 15) match the black wire to the
ground pin.
(3-pin PWR_FAN1)
(see p.2 No. 20)
CPU Fan Connector Please connect the CPU fan
(4-pin CPU_FAN1) cable to this connector and
(see p.2 No. 1) match the black wire to the
ground pin.
GND
+12V
CPU_FAN_SPEED
FAN_SPEED_CONTROL
4 3 2 1
GND
+12V
CHA_FAN_SPEED
GND
+12V
FAN_SPEED

1414
1414
14 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish EnglishEnglish
English
ATX 12V Power Connector Please note that it is necessary
(4-pin ATX12V1) to connect a power supply with
(see p.2 No. 2) ATX 12V plug to this connector.
Failing to do so will cause power
up failure.
Chassis Intrusion Header Thismotherboard supportsCASE
(2-pin CI1) OPEN detection feature that
(see p.2 No. 21) detects if the chassis cover has
beenremoved. This feature
requires a chassis with chassis
intrusion detection design.
1
Signal
GND
2. BIOS Information2. BIOS Information
2. BIOS Information2. BIOS Information
2. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to
enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to
enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +
<Delete>, or pressing the reset button on the system chassis. The BIOS Setup program
is designed to be user-friendly. It is a menu-driven program, which allows you to scroll
through its various sub-menus and to select among the predetermined choices. For the
detailed information about BIOS Setup, please refer to the User Manual (PDF file) con-
tained in the Support CD.
3. Software Support CD information3. Software Support CD information
3. Software Support CD information3. Software Support CD information
3. Software Support CD information
This motherboard supports various Microsoft®Windows®operating systems: 8.1 32-bit
/ 8.1 64-bit / 8 32-bit / 8 64-bit / 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP 32-
bit / XP 64-bit. The Support CD that came with the motherboard contains necessary
drivers and useful utilities that will enhance motherboard features. To begin using the
Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu auto-
matically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear
automatically, locate and double-click on the file “ASRSETUP.EXE” from the “BIN” folder
in the Support CD to display the menus.

1515
1515
15
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
SpezifikationenSpezifikationen
SpezifikationenSpezifikationen
Spezifikationen
Plattform - MicroATX-Formfaktor
A-Stil - Heim-Cloud(N68C-GS4 FX)
CPU - Unterstützung von SocketAM3+-Prozessoren
- Unterstützung von SocketAM3-Prozessoren: AMD PhenomTM
II X6 / X4 / X3 / X2 (außer 920 / 940) /Athlon X4 / X3 / X2 /
Sempron-Prozessor
- Unterstützung für Socket AM2+ / AM2-Prozessoren: AMD
PhenomTM FX / Phenom / Athlon 64 FX /Athlon 64 X2 Dualkern
/Athlon X2 Dualkern /Athlon 64 / Sempron-Prozessor
-Acht-Kern-CPU-bereit
- Unterstützt UCC (Unlock CPU Core)
- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD
- FSB 1000 MHz (2.0 GT/s)
- Unterstützt Untied-Übertaktungstechnologie
- Unterstützt Hyper-Transport-Technologie
Chipsatz -NVIDIA®GeForce 7025 / nForce 630a
Speicher - Unterstützung vonDual-Kanal-Speichertechnologie
- 2 x Steckplätze fürDDR3
- UnterstütztDDR3 1600/1333/1066 non-ECC, ungepufferter
Speicher
- Max. Kapazität des Systemspeichers: 16GB
- 2 x Steckplätze fürDDR2
- UnterstütztDDR2 1066/800/667/533 non-ECC, ungepufferter
Speicher
- Max. Kapazität des Systemspeichers: 8GB
Erweiterungs- - 1 x PCI Express x16-Steckplätze
steckplätze - 1 x PCI Express x1-Steckplätze
- 2 x PCI -Steckplätze
Onboard-VGA - IntegrierterNVIDIA®GeForce 7025Grafikchip
- DX9.0 VGA, Pixel Shader 3.0
- Maximal gemeinsam genutzter Speicher 256 MB
- UnterstütztD-Sub mit einer maximalenAuflösung von
1920 x 1440 bei 60 Hz
Audio - 5.1 CH HDAudio (RealtekALC662 / VIA®VT1705 Audio Codec)
LAN N68C-GS4FX:
- Qualcomm®Atheros®AR8171, speed 10/100/1000 Mb/s
- Unterstutzt Qualcomm®Atheros®Security Wake On
Internet-Technologie
- Unterstützt Wake-On-LAN
DeutschDeutsch DeutschDeutsch
Deutsch

1616
1616
16 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
DeutschDeutsch DeutschDeutsch
Deutsch
- Unterstützt energieeffizientes Ethernet 802.3az
- Unterstützt PXE
N68C-S4FX:
-Atheros®AR8152, speed 10/100 Mb/s
- Unterstützt Wake-On-LAN
- Unterstützt PXE
E/A-Anschlüsse I/O Panel
an der - 1 x PS/2-Mausanschluss
Rückseite - 1 x PS/2-Tastaturanschluss
- 1 x Serieller port: COM1
- 1 x VGAport
- 4 x Standard-USB 2.0-Anschlüsse
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
- HDAudiobuchse:Audioeingang / Lautsprecher vorne /
Mikrofon
Speicher - 4 x SATA2-Anschlüsse, unterstützt bis 3.0 Gb/s
Datenübertragungsrate, unterstützt RAID (RAID0, RAID 1,
RAID0+1, RAID 5, JBOD),NCQ und “Hot Plug” Funktionen
Anschlüsse - 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)
- 1 x FDD-Anschlüsse
- 1 x Druckerport-Anschlussleiste
- 1 x Verteiler fur Gehauseeindringversuche
- 1 x CPU-Lüfteranschluss (4-polig)
- 1 xGehäuse-Lüfteranschluss (3-polig)
- 1 xNetzteillufteranschluss (3-polig)
- 1 x 24-pinATX-Netz-Header
- 1 x 4-pin anschluss für 12V-ATX-Netzteil
- 1 xAnschluss fürAudio auf derGehäusevorderseite
- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
USB 2.0-Anschlüsse)
BIOS - 8Mb AMI BIOS
-AMI legal BIOS mit Unterstützung für “Plug and Play”
-ACPI 1.1-Weckfunktionen
-JumperFree-Modus
- SMBIOS 2.3.1
- CPU, VCCM,NB Stromspannung Multianpassung
Support-CD - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation),
Google Chrome Browser und Toolbar, Start8 (30-Tage-
Testversion)
Hardware Monitor -CPU-Temperatursensor
-Motherboardtemperaturerkennung

1717
1717
17
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
DeutschDeutsch DeutschDeutsch
Deutsch
-Drehzahlmessung für CPU-Lüfter
-Drehzahlmessung fürGehäuselüfter
-CPU-Lüftergeräuschdämpfung
-GEHAUSE OFFEN-Erkennung
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
Betriebssysteme - Unterstützt Microsoft®Windows®8.1 32-Bit / 8.1 64-Bit / 8
32-Bit / 8 64-Bit / 7 32-Bit / 7 64-Bit / VistaTM 32-Bit /
VistaTM 64-Bit / XP 32-Bit / XP 64-Bit
Zertifizierungen - FCC, CE, WHQL
-Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung
gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com

1818
1818
18 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
SpécificationsSpécifications
SpécificationsSpécifications
Spécifications
Format - Facteur de forme MicroATX
A-Style - Home Cloud (N68C-GS4 FX)
CPU - Prise en charge des processeurs sur socket AM3+
- Prise en charge des processeurs sur socketAM3: Processeur
PhenomTM II X6 / X4 / X3 / X2 (sauf 920 / 940) /Athlon II X4 / X3
/ X2 / Sempron d’AMD
- Prise en charge des processeurs SocketAM2+ / AM2:AMD
PhenomTM FX / Phenom /Athlon 64 FX / Athlon 64 X2Dual-Core
/Athlon X2Dual-Core / Athlon 64 / processeur Sempron
- Prêt pour processeurs Huit-Core
- Supporte UCC (Unlock CPU Core)
- Supporte la technologie Cool ‘n’ QuietTM d’AMD
- FSB 1000 MHz (2.0 GT/s)
- Prend en charge la technologie Untied Overclocking
- Prise en charge de la technologie Hyper Transport
Chipsets - NVIDIA®GeForce 7025 / nForce 630a
Mémoire - Compatible avec la Technologie de Mémoire à CanalDouble
- 2 x slotsDIMM DDR3
-SupporterDDR31600/1333/1066non-ECC,sansamortissement
mémoire
- Capacité maxi de mémoire système: 16GB
- 2 x slotsDIMM DDR2
- SupporterDDR2 1066/800/667/533 non-ECC, sans
amortissement mémoire
- Capacité maxi de mémoire système: 8GB
Slot d’extension - 1 x slot PCI Express x16
- 1 x slot PCI Express x1
- 2 x slots PCI
VGA sur carte -NVIDIA®graphiqueGeForce 7025 intégré
- VGADX9.0, nuanceur de pixels 3.0
- mémoire partagée max 256MB
- Prend en charge leD-Sub avec une résolution maximale
jusqu’à 1920x1440 @ 60Hz
Audio - 5.1 Son haute définition de CH (codec audio RealtekALC662 /
VIA®VT1705)
LAN N68C-GS4FX:
- Qualcomm®Atheros®AR8171, vitesse 10/100/1000 Mb/s
- Prend en charge la technologie Qualcomm®Atheros®Security
Wake On sur Internet
FrançaisFrançais FrançaisFrançais
Français

1919
1919
19
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
FF FF
Franran
ranran
rançaisçais
çaisçais
çais
- Support du Wake-On-LAN
- Prend en charge la fonction d’économie d’énergie Ethernet
802.3az
- Support du PXE
N68C-S4FX:
-Atheros®AR8152, vitesse 10/100 Mb/s
- Support du Wake-On-LAN
- Support du PXE
Panneau arrière I/O Panel
E/S - 1 x port souris PS/2
- 1 x port clavier PS/2
- 1 x port série: COM1
- 1 x port VGA
- 4 x ports USB 2.0 par défaut
- 1 x port LANRJ-45 avec LED(ACT/LEDCLIGNOTANTE et
LED VITESSE)
- Prise HDAudio: Entrée Ligne / Haut-parleur frontal /
Microphone
Stockage - 4 x connecteurs SATA2, prennent en charge un taux de
transfert de données pouvant aller jusqu’à 3.0Go/s,
supporte RAID (RAID 0, RAID 1, RAID 0+1, RAID 5, JBOD),
NCQ et “Hot-Plug” (Connexion à chaud)
Connecteurs - 1 x ATA133 IDE connecteurs
(prend en charge jusqu’à 2 périphériques IDE)
- 1 x Port Disquette
- 1 x embase de port d’impression
- 1 x Embase d’intrusion chassis
- 1 x Connecteur pour ventilateur de CPU (br. 4)
- 1 x Connecteur pour ventilateur de Châssis (br. 3)
- 1 x connecteur pour ventilateur d¡¦alimentation (3 broches)
- 1 x br. 24 connecteur d’alimentation ATX
- 1 x br. 4 connecteur d’alimentation 12VATX
- 1 x Connecteur audio panneau avant
- 3 x En-tête USB 2.0 (prendre en charge 6 ports USB 2.0
supplémentaires)
BIOS - 8Mb BIOS AMI
- Support du “Plug and Play”
- Compatible pour événements de réveilACPI 1.1
-Gestion jumperless
- Support SMBIOS 2.3.1
- CPU, VCCM,NB Tension Multi-ajustement

2020
2020
20 ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
FrançaisFrançais FrançaisFrançais
Français
CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation),
GoogleChromeBrowser etToolbar,Start8(30 joursd’évaluation)
Surveillance - Détection de la température de l’UC
système - Mesure de température de la carte mère
- Tachéomètre ventilateur CPU
- Tachéomètre ventilateur châssis
- Ventilateur silencieux d’unité centrale
-Detection d’OUVERTUREDE BOITIER
- Monitoring de la tension: +12V, +5V, +3.3V, Vcore
OS - Microsoft®Windows®8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-bit
/ 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP 32-bit /
XP 64-bit
Certifications - FCC, CE, WHQL
- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web:
http://www.asrock.com