Assured Wireless MegaMobile AW12 User manual

assured-wireless.com
QSGmobile2022v1
Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change
without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation.
QUICK START GUIDE
This quick start guide gives the basic steps for installing the AW12 MegaMobile unit in vehicles.
The following contents are included:
■ AW12-DE modem
■ AW12-PC-EI USB to Ethernet converter
■ Vehicle mounting bracket
■ (2) M6 screws and (2) M6 lock washers
■ (4) M3 screws and (4) M3 lock washers
■ Ethernet cable
■ USB screwtight cable
■ DC power cable (4-pin Molex)
■ DC power cable (modem to Ethernet converter)
■ SIM extractor tool
You will also need the following (not included in your kit):
■ GPS active/passive antenna
■ LTE antenna (need 3 leads)
■ Activated FirstNet micro SIM card
■ Small Phillips head screwdriver
Note. The antennas can be purchased as separate units or as a single unit. See our recommended
antennas at assured-wireless.com/products/antennas.
2 Insert SIM card
Note. Your distributor may have already inserted the SIM. If
so, please skip to section 3.
1 Locate the SIM card slot on the side of the AW12 modem.
2 Remove the screw on the SIM slot door.
3 Use the depression on the upper left corner of the SIM
slot door to open the door. You should now see the edge
of the silver SIM tray.
4 Insert the included SIM extractor tool into the hole on the
SIM tray; the tray should pop partway out.
5 Remove the SIM tray completely.
6 Insert your activated FirstNet SIM into the tray. Note that
the tray is notched, so the card can only be inserted the
correct way.
7 Re-insert the SIM tray into its slot.
8 Replace the SIM slot door and replace the screw, being
careful not to overtighten.
1
Ensure you have all the necessary equipment
MegaMobile Installation
Align notch and
insert in tray

AW12 VEHICLE INSTALLATION KIT
QUICK START GUIDE
assured-wireless.com
QSGmobile2022v1
Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change
without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation.
AW12 Modem USB to Ethernet Converter
1 Use the included M6 screws and washers
and a Phillips #2 screwdriver to mount the
modem to the mounting bracket. (Put the
antenna ports to the edge as shown.)
2 Use the included M3 screws and washers
to mount the USB to Ethernet converter to
the mounting bracket. (Put the side with
the ethernet port to the same edge as the
modem antenna ports.)
Connect the USB-C to USB-A cable between the modem and the USB to Ethernet converter:
1 Insert the cable with the USB C connector. Insert it into the port labeled USB on the modem. and tighten the
thumb
screws. Be careful not to overtighten.
2 Insert the USB-A end of the
cable into the port on the
USB to Ethernet converter
labeled Modem and tighten
the thumb screw. Do not
overtighten.
Connect the short power cable:
1 Find the end of cable with the
light green connector. Insert
it into the port labeled PWR
IN on the modem. Twist to
tighten.
2 Insert the other end of the
cable into the port on the USB
to Ethernet converter labeled
PWR OUT .
AW12 Modem USB to Ethernet Converter
Install the bracket in the vehicle with the proper hardware. Mount securely near the power source. Where and
how you install the bracket will vary based on vehicle.
3
Mount modem and Ethernet converter on bracket
4
Connect power and communication between modules
5
Mount bracket in vehicle

AW12 VEHICLE INSTALLATION KIT
QUICK START GUIDE
assured-wireless.com
QSGmobile2022v1
Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change
without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation.
IGNITION
BATTERY +
NOT USED
BATTERY -
Antenna
To router
To vehicle power
1 Install the antennas on the roof of the vehicle. For best performance, we recommend you keep at least one
meter of separation between the antennas installed on the roof.
2 Connect the ends of the antenna cables into the four RF ports on the modem as follows:
■ PR I por t: L TE - 1 cable
■ B14 port: B14 cable
■ DIV port: LTE-2 cable
■ GNSS port: GPS/GNSS cable
Note. See our antenna recommendations at assured-wireless.com/products/antennas.
1 Insert the ethernet cable into the RJ-45 port labeled PoE+ on the USB to Ethernet converter and then
connect the ethernet cable to the WAN port of your router.
2 Locate the DC power cable with the 4-pin Molex connector. Insert that connector into the port labeled PWR
IN on the bottom of the USB to Ethernet converter, and then connect the unterminated ends of the DC
power cable to the power source of the vehicle.
3 Refer to your router user manual for router configuration. Please make sure the MTU size setting in your
router is 1342 or as otherwise advised at https://iotdevices.att.com/att-iot/FirstNetMTU.aspx.
Note. If there is no ignition connection, be sure to connect the orange and red leads together.
6
Install antennas
7
Connect power and Ethernet cables