Tenda D810R ADSL2+ User manual

Copyright Statement
is the registered trademark of Shenzhen
Tenda Technology Co., Ltd. Other trademark or trade
name mentioned herein are the trademark or
registered trademark of the company. Copyright of the
whole product as integration, including its accessories
and software, belongs to Shenzhen Tenda Technology
Co., Ltd. Without the permission of Shenzhen Tenda
Technology Co., Ltd, individual or party is not allowed to
copy, plagiarize, imitate or translate it into other
languages.
All the photos and product specifications mentioned in
this manual are for references only, as the upgrading of
software and hardware, there will be changes. And if
there are changes, Tenda is not responsible for
informing in advance. If you want to know more about
our products information, please visit our website at
www.tenda.cn

D810R ADSL2+ Router User Guide
PTC General Warning
1 The grant of a Telepermit for any item of
terminal equipment indicates only that
Telecom has accepted that the item complies
with minimum conditions for
connection to its network. It indicates no
endorsement of the product by Telecom,
nor does it provide any sort of warranty. Above
all, it provides no assurance that
any item will work correctly in all respects with
another item of Telepermitted
equipment of a different make or model, nor
does it imply that any product is
compatible with all of Telecom's network
services.
CONTENTS

D810R ADSL2+ Router User Guide
CHAPTER 1 OVERVIEW........................................................... 1
1.1 Product Introduction.................................................. 1
1.2 Product Features......................................................... 2
1.3 Supporting Protocol ................................................... 3
1.4 Data Encapsulation ................................................... 3
CHAPTER 2 HARDWARE INSTALLATION ............................... 4
2.1 ADSL Router Connection .......................................... 4
2.2 USB Installation............................................................. 4
CHAPTER 3 BEFORE WEB MANAGEMENT CONFIGURATION
..................................................................................................5
3.1 Network Configuration of Your Computer............. 5
3.2 Verifying the Connection.......................................... 8
3.3 Logging in to the Router............................................ 9
CHAPTER 4 QUICK INSTALLATION GUIDE.......................... 10
4.1 Configure the PPPoE................................................11
4.2 Configure the PPPoA...............................................13

D810R ADSL2+ Router User Guide
4.3 Configure the MER ...................................................15
4.4 Configure the IPoA................................................... 18
CHAPTER 5 CONFIGURATION DESCRIPTION..................... 20
5.1Device Information....................................................20
5.2Advanced Settings.................................................... 23
5.2.1 WAN..................................................................23
5.2.2 LAN....................................................................48
5.2.3 NAT....................................................................50
5.2.4 Security .............................................................56
5.2.5 Routing..............................................................64
5.2.6. DNS...................................................................66
5.2.7 DSL.....................................................................71
5.3 DHCP..........................................................................72
5.4 System Tool ................................................................73
5.4.1 Settings..............................................................73
5.4.2 System Log .......................................................75
5.4.3 Internet Time.....................................................77
5.4.4 Access Control.................................................78
5.4.5 Software Update .............................................81

D810R ADSL2+ Router User Guide
5.4.6 Save/Reboot....................................................81
CHAPTER 6 APPENDIX.......................................................... 82
Appendix 1: Troubleshooting...................................82
Appendix 2: FAQ ......................................................84
CHAPTER 7 WALL-MOUNTING PLACEMENT......................85

D810R ADSL2+ Router User Guide
1
Chapter 1 Overview
1.1 Product Introduction
D810R ADSL2+ Router complies with ADSL, ADSL2 and
ADSL2+ standards. Supporting up to 24Mbps
downstream rate and 1Mbps upstream rate, it supports
multiple network protocols and provides NAT Router
and Bridge functions. In addition, the intelligent software,
Setup Wizard, can assist you to access the Internet fast
and easily. Powerful and exquisite, it is the best choice
for SOHO and small enterprise users to share the
Internet.

D810R ADSL2+ Router User Guide
2
1.2 Product Features
Provides up to 24Mbps downstream rate and
1Mbps upstream rate
Supports DHCP, NAT, IGMP, ICMP, ARP
One 10/100M Auto-Negotiation RJ-45 Ethernet
port for network adapter, Hub and switch
connectivity
One RJ-11 port and Voice Splitter included
One USB port support for connecting PC’s USB
port
Provides Web-based management and firmware
upgrade
Complies with ADSL, ADSL2 and ADSL2+ standards
Provides NAT Router and Bridge functions
Compatible with all mainstream DSLAM (CO)
Provides PPPOE, PPPOA, CLIP protocols
Supports firewall and hacker attack prevention
Supports Internet Multimedia
Provides static and dynamic routes
Up to 6.5km (telephone line) transmission distance
Setup Wizard support for fast and easy
configurations

D810R ADSL2+ Router User Guide
3
1.3 Supporting Protocol
Supports full-rate ADSL2+ standard
ANSI T1. 413 Issue 2
ITU-T G. 992. 1 (G. dmt)
ITU-T G. 992. 2 (G. Lite)
ITU-T G. 992. 3
ITU-T G. 992. 5
1.4 Data Encapsulation
Supports RFC 1483 Bridge, RFC 1483 Router
Supports Classical IP over ATM (RFC 1577)
Supports PPP over ATM(RFC 2364)
Supports PPP over Ethernet (RFC 2516)

D810R ADSL2+ Router User Guide
4
Chapter 2 Hardware Installation
2.1 ADSL Router Connection
1. Connect one end of the telephone line to the
LINE port of the D810R and the other end to the
MODEM port of the voice splitter.
2. Connect the power adapter to the PWR port of
the D810R.
3. Use an Ethernet cable to connect the LAN port
with the NIC of your computer.
2.2 USB Installation
To connect the device to the USB interface of the
computer, please follow the steps below:
1. Connect to the USB port of the D810R through a
USB cable.
2. Connect the other end of the cable to the
computer’s USB port.
3. Set up the USB driver provided by the CD-ROM.

D810R ADSL2+ Router User Guide
5
Chapter 3 Before Web Management
Configuration
3.1 Network Configuration of Your Computer
1
．
On the desktop of your
computer, right-click
“My Network Places”,
and then select
“Properties” in the
shortcut menu.
2. In the window that
appears, right-click
“Local Area
Connection”, and then
select "Properties”.

D810R ADSL2+ Router User Guide
6
3
．
In the pop-up dialog
box, check “Internet
Protocol (TCP/IP)” and
then click “Properties”.
4. In the window that
appears, select
“Obtain an IP address
automatically (O)” or
“Use the following IP
address (S)”.
1) When “Obtain an IP
address automatically
(O)” is selected, the
window is as shown in
the right figure.

D810R ADSL2+ Router User Guide
7
2) “Use the following IP
address”:
IP address: 192.168.1.XXX
(XXX ranges 2 ~ 254)
Subnet mask:
255.255.255.0
Default gateway:
192.168.1.1
DNS server: Enter the
local DNS server address
(for this address, you can
consult your ISP) or the
router’s default gateway
as the DNS server.
At the end of the setting,
click “OK” to submit the
settings. And then click
“OK” in the “Local Area
Connection Properties”
window.

D810R ADSL2+ Router User Guide
8
3.2 Verifying the Connection
1
．
Select “Start→Programs
→Accessories→Comm
and Prompt”.
According to the
format shown in the
right figure, enter “Ping
192.168.1.1” and press
Enter. If the system
gives the result shown
in the right figure, the
connection between
your computer and the
router is OK.

D810R ADSL2+ Router User Guide
9
3.3 Logging in to the Router
1
．
Open the web browser,
and enter
“http://192.168.1.1” in
the address field, and
then press Enter.
2
．
In the pop-up login
window, enter the user
name (“admin”) and
password (“admin”),
and click “OK” (both
user name and
password are “admin”
by default).
3
．
If the user name and
password entered are
correct, the browser
displays the
administrator window
shown right.

D810R ADSL2+ Router User Guide
10
Chapter 4 Quick Installation Guide
In the Wizard page,
Select the required your
“Country” and “Area”
from the drop-down lists.
If you can not find your
country and city in these
lists, you can consult your
ISP and manually enter
the VPI and VCI values of
your area. After that, click
“Next”.

D810R ADSL2+ Router User Guide
11
4.1 Configure the PPPoE
1
．
Select “PPP over Ethernet
(PPPoE)”. Click “Next”.
2
．
Enter the PPP user name
and password provided
by the ISP. If the ISP also
provides the PPPoE
service name, you can
enter the corresponding
value; otherwise, keep
this field null. Use the
default values for other
options. For their more
settings, refer to the
detailed description in
the Advanced Settings.

D810R ADSL2+ Router User Guide
12
3
．
Click “Next” and check to
enable the WAN service
(enabled by default).
4
．
Click “Next” to display the
window shown the
summary of your settings.
5
．
Click “Save/Reboot” to
activate your settings. The
system automatically
establishes connection in
a few minutes.

D810R ADSL2+ Router User Guide
13
4.2 Configure the PPPoA
1
．
Select “PPP over ATM
(PPPoA)”. Click “Next”.
2. Enter the PPP user
name and password
provided by the ISP. If
the ISP also provides
the PPPoA service
name, you can enter
the corresponding
value; otherwise, keep
this field null. Use the
default values for other
options. For their more
settings, refer to the
detailed description in
the Advanced Settings.

D810R ADSL2+ Router User Guide
14
3. Click “Next” and
check to enable the
WAN service (enabled
by default).
4. Click “Next” to display
the window shown the
summary of your
settings.
5. Click “Save/Reboot”
to activate your
settings. The system
automatically
establishes connection
in a few minutes.