ASTEL LPS1800 User manual
ALOA
PATH
LED
LIGHT
Operating Instructions
2
CONTENTS
Preface...............................................................................................................................................................3
Features .............................................................................................................................................................3
Precautions ........................................................................................................................................................3
Components.......................................................................................................................................................4
Installation and Connection................................................................................................................................6
Controls..............................................................................................................................................................7
Technical Specifications.....................................................................................................................................8
Declaration of Conformity.................................................................................................................................10
Warranty...........................................................................................................................................................11
_________________________________________________________________________________
3
PREFACE
The ALOA series of bollard garden light with
Direct-Drive LED mains power supply is
designed to use the latest LED lighting
technology.
Uniformly designed very robust casings with
different curved leaves allow the proper choice
of light distribution for various layouts around
buildings and gardens.
The ALOA series is available in painted zinc-
plated steel casings. The lighting is available in
warm white, daylight white and cool white with
1 mid-power LED array.
The most advanced AC Direct-Drive LED
mains power supply unit with built-in
microprocessor enables network connection
and complete DMX512 lighting control by using
optional interfaces.
FEATURES
•Painted Steel Casing
•1 Mid-Power LED Array
•Cool, Daylight or Warm White Lighting
•High Grade Polycarbonate Glass /
Tempered Glass Optical Window
•Reflector with/without Holographic Diffuser
•AC Direct-Drive LED Mains Power Supply
•Low Flicker Index
•Triac and Phase Dimming
•Built-in ASTEL Protocol for DMX512 Control -
Flicker Free Dimming
•AC Power Line Surge Protection
•Low Power Consumption
•Simple Installation
PRECAUTIONS
•The path light has to be installed and used
in accordance with the instructions of this
manual only.
•The power supply has to be disconnected
before installation.
•Avoid using this unit near appliances
generating strong magnetic fields.
•The optical window has to be cleaned with
a mild soap or detergent and lukewarm
water by using a soft cloth or sponge. Do
not use abrasive or highly alkaline cleaners.
Never scrape with razor blades or other
sharp instruments. Benzene, leaded
gasoline, acetone or carbon tetrachloride
should never be used.
•Do turn power off immediately and refer
servicing to qualified service personnel if
the interior & exterior light does not operate
normally following the operating
instructions.
4
COMPONENTS
1
2
3
LPS1800
LPD1800 LBS1800 LBD1800 LAS1800 LAD1800 LCD1800
Model
Description
LPS1800
Single-Side Closed, 1 Mid-Power LED Array
LPD1800
Double-Side Closed, 1 Mid-Power LED Array
LBS1800
Single-Side Reflection, 1 Mid-Power LED Array
LBD1800
Double-Side Reflection, 1 Mid-Power LED Array
LAS1800
Half-Side Closed, 1 Mid-Power LED Array
LAD1800
Full-Side Closed, 1 Mid-Power LED Array
LCD1800
Double-Side Closed, 1 Mid-Power LED Array
Color of lighting
Description
WW
Warm White
DW
Daylight White
CW
Cool White
5
(1) Path light casing
Painted zinc-plated steel casing with reflective surface beam.
(2) Optical window
High-Grade Polycarbonate Glass Optical Window.
(3) AC Direct-Drive light power supply unit
AC Direct-Drive smart light mains power supply unit built-in robust holder with fixing holes and 5-pole
multi-core cable to connect 230Vac power supply and control.
6
INSTALLATION AND CONNECTION
The installation have to be realized by qualified personnel.
Note:
•Do not cover the path light optical window with any kind of temperature isolating material.
The path light is protected by a temperature sensor against over-heating. When the
temperature of the flood-path light exceeds 85°C the path light is automatically switched
off.
The power supply has to be connected through the main switch (not included) and protected by a
fuse (not included).
Note:
•The power supply has to be switched off before installation.
The light has to be connected as described in the table below:
ALOA
FUNCTION
wire color
wire mark
Brown
L
Line 230 Vac
Blue
N
Neutral 230 Vac
Yellow/Green
Earth 230 Vac
Gray
C+
CONTROL+ (24 Vdc max.)
Black
C-
CONTROL- (24 Vdc max.)
For basic control of the light the CONTROL wires have to be connected through the momentary
switch (not included) to the power source / 12-24Vdc (not included) by using a 2-pole signal cable
extension (not included).
For DMX512 control optional LXU01 interface can be connected to the CONTROL wires by using a
2-pole signal cable (not included).
Note:
•When two or more lights are connected in the lighting system the control wires can be
connected in parallel and all the lights then can be controlled by using only one
momentary switch or LXU01 interface.
Earthing
The flood-path light has to be earthed by using a pre-tinned green wire with a yellow stripe a
minimum of 8 AWG (8.36 mm2). The wire has to be connected to the path light by the help of one
assembling screw.
7
CONTROLS
Control by momentary switch
Remote control by momentary switch can be used to turn-on and turn-off the light and to control the
luminosity.
Turning on / off
Press the momentary switch momentary.
Dimming
When the light is on, press the momentary switch longer until the desired power is achieved.
Turning on minimum
When the light is off, press the momentary switch longer (e.g. one second or more) until the light is
turned on at minimum power.
Set default
Press the momentary switch for min. 40 seconds or until the light is turned off.
DMX512 control
The network connection to control the light with the standard DMX512 protocol is enabled by using
optional LXU01 interface.
8
TECHNICAL SPECIFICATIONS
Power supply 230 Vac / 90 mA max.
Optical window High Grade Polycarbonate Glass / Tempered Glass
Color rendering index (CRI) 80
Luminous flux max. 1.800 lm (cool white)
Control voltage 12-24 Vdc
ASTEL protocol default address 1
Operating temperature -10°C - +50°C
Casing Painted Zinc-Plated Steel
Protection IP 67
Dimensions 1.015 x 310 x 200 mm
Weight max. 23 kg
Design and specifications subject to change without notice.
9
10
DECLARATION OF CONFORMITY
according to IEC Guide 22 and EN 45014
Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in
trgovino, d.o.o.
Manufacturer's Address: Dutovlje 138
6221 Dutovlje
Slovenija
declares that the products
Item, Product Name and Model Number: 1. Path LED light ALOA series
conform to the following Product Specifications:
EMC: EN 55015:2006 + A1:2007
EN 61547:1995 + A1:2000 + A2:2009
EN 61547:2009
Safety: EN 60598-2-18:1995/A1:2012
EN 60529:1992+A2:2013
Supplementary Information:
The products herewith comply with the requirements of the following Directives and carry the CE-
marking accordingly:
-the EMC Directive 2014/30/EU
-the RoHS Directive (EU)2015/863
ASTEL d.o.o.
Dutovlje 138
6221 Dutovlje
Slovenija
26th September, 2019
11
WARRANTY
1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in
workmanship and materials under normal use and service.
2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase
must be included, to establish that it is inside the warranty period.
3. This Warranty is transferrable and covers the product for the specified time period.
4. In case any part od the equipment proves to be defective, other than those parts excluded in
paragraph 5 below, the owner should do the following:
(a) prepare a detailed written statement of the nature and circumstances of the defect, to the best
of the Owner’s knowledge, including the date of purchase, the place of purchase, the name and
adress of the installer, and the Purchaser’s name, adress and telephone number;
(b) the Owner should return the defective part or unit along with the statement referenced in the
preceding paragraph to the warrantor, ASTEL d.o.o., or an authorized distributor,
postage/shipping prepaid and at the expense of the Purchaser;
(c) if upon the Warrantor’s or authorized distributor’s examination, the defect is determined to
result from defective material or workmanship, the equipment will be repaired or replaced at the
Warrantor’s option without charge, and returned to the Purchaser at the Warrantor’s expense;
(d) no refund of the purchase price will be granted to the Purchaser, unless the Warrantor is
unable to remedy the defect after having a reasonable number of opportunities to do so. Prior
to refund of the purchase price, Purchaser must submit a statement in writing from a
professional supplier that the installation instructions of the Operating Instructions manual have
been complied with and that the defect remains;
(e) warranty service shall be performed only by the Warrantor, or an authorized distributor, and
any attempt to remedy the defect by anyone else shall render this warranty void.
5. There shall be no warranty for defects or damages coused by faulty installation or hook-up, abuse
or misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or
water immersion except for equipment specially designed as waterproof.
6. There shall be no responsibility or liability whatsoever on the part of the Warrantor or its
employees and representatives for injury to any person or persons, or damage to property, loss of
income or profit, or any other consequential or resulting damage or cost which may be claimed to
have been incurred through the use or sale of the equipment, including any possible failure or
malfunction of the equipment, or part thereof.
This manual suits for next models
6
Table of contents
