Bunker Hill Security 58195 User manual

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual (or month and year of purchase if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference. 22g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2021 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 58195
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 4
Setup .......................................................... 4
Operation.................................................... 5
Maintenance.............................................. 66
Parts List and Diagram............................... 2
Warranty ..................................................... 8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. Keep installation area clean.
Cluttered areas invite accidents.
2. Observe installation area conditions. Keep
work area well lit during installation.
3. Check for damaged parts. Before using
any product, any part that appears damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function. Check for any broken or damaged
parts and any other conditions that may affect its
operation. Replace or repair damaged or worn
parts immediately. Do not use the Security Light
if any switch does not turn on and off properly.
4. Replacement parts and accessories. When
servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
5. Check hardware and assembled parts
after assembling. All connections should
be tight and hardware tightened.
6. Keep children away. Mount the Light, Solar
Panel, and Cord out of children’s reach.
7. Dress properly. Protective, electrically non-
conductive clothes and nonskid footwear are
recommended when working with the Solar
Powered Security Light. Wear restrictive
hair covering to contain long hair.
8. Use eye protection. Wear ANSI-approved impact
safety goggles when setting up this product.

Page 3For technical questions, please call 1-888-866-5797.Item 58195
SAFETYOPERATIONMAINTENANCE SETUP
9. Maintain products with care. Keep the Solar
Powered Security Light clean for better and safer
performance. Inspect the Light periodically. If
damaged, have it repaired by a qualified technician.
10. Do not overreach. Keep proper footing and
balance at all times. If a ladder is to be used during
installation, it should be supported by an assistant.
11. Do not set up the Solar Powered Security Light
if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your
judgement or reflexes are impaired while taking
drugs. If there is any doubt, do not set up the Light.
12. Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
13. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
14. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140°F or incinerate.
SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-888-866-5797. Item 58195
SAFETY OPERATION MAINTENANCESETUP
Specifications
Lamp 136 LED,30 W
Battery Pack 3.7 V, 4400 mAh
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the
following pages, refer to Parts List and Diagram on page 4.
Installation
1. Decide where to place the Security Light.
a. The Security light is equipped with a Solar Panel.
b. The Solar Panel must be set in a location
that receives full, direct sunlight, a minimum
of 8 hours a day. Ideally, the Solar
Panel should be angled slightly toward
the South (northern hemisphere).
2. Mount the Security Light:
a. Place the Security light in the desired location,
adjusting the unit to best fit the surface.
WARNING! TO AVOID serious INJURY
FROM ELECTRIC SHOCK, verify the
installation surface has no hidden utility
lines before drilling or driving screws.
b. Using the Security Light’s base as a template,
mark the hole locations to install the light.
c. Drill holes for the installation screws
for top left and right corners.
d. Insert the screws into the holes and check fitting.
WARNING! TO AVOID serious INJURY
FROM ELECTRIC SHOCK, verify the
installation surface has no hidden utility
lines before drilling or driving screws.
e. Another option for installation, use the double-
sided tape for the back of light. Choose
desired location for sticker on back surface
and peel one side to mount onto surface.
Balance stickers on both sides. Peel off other
side and place light onto desired location.
Solar Panel
Motion Sensor
Lamp
Power Switch
Behind Lamp
Functions

Page 5For technical questions, please call 1-888-866-5797.Item 58195
SAFETYOPERATIONMAINTENANCE SETUP
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Initial Battery Charging
Before the Security Light can operate properly, the
battery needs to be fully charged. To charge the battery:
1. Turn OFF the Power Switch.
2. Expose the Solar Panel to 3 DAYS OF FULL
DIRECT SUNLIGHT to fully charge the battery.
3. After charging, turn the Power Switch to ON. The
lamp will illuminate at night when motion is detected.
This indicates that the unit is working properly.
CAUTION
The UNIT WILL NOT FUNCTION
UNLESS:
The Solar Panel is first charged for
3 DAYS OF FULL SUN
with the SENSOR POWER OFF.
Power Switch
The Power Switch is located behind the security lamp.
OFF: Flip switch to power off.
ON: Flip switch to on position. The Lamp remains off
throughout the day with enough natural light. At night,
the Lamp will illuminate automatically for 30 seconds
when motion is detected by the Motion Sensor Head.
Testing the Light
After the battery is charged, walk slowly around the detection area. The sensor detects
infrared radiation given off by a person or animal. This triggers the Lamp to illuminate. The
light should go on in the area that you set up the Security Light to monitor.
Relocate the unit and re-test until the unit functions as desired.
Repeat the test procedure as needed when weather and/or temperature changes.

Page 6 For technical questions, please call 1-888-866-5797. Item 58195
SAFETY OPERATION MAINTENANCESETUP
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the unit. Check for:
• leaking, swollen, or cracked battery,
• loose hardware,
• misalignment or binding of parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the unit with clean cloth.
3. Keep Solar Panel free of dirt and debris to maintain
optimum efficiency in recharging the battery.
Battery Removal and Disposal
1. The battery is located inside the Lamp assembly.
2. Turn the Lamp off and remove
the screws on the back.
3. Disconnect the battery and remove it from the Lamp.
4. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140°F or incinerate.

Page 7For technical questions, please call 1-888-866-5797.Item 58195
SAFETYOPERATIONMAINTENANCE SETUP
Troubleshooting
Problem Possible Causes Likely Solutions
Light won’t
turn on.
1. Power is not on.
2. Motion sensor not
detecting movement.
3. Battery pack not fully charged.
1. Check that Power Switch is set to ON.
2. Relocate the Motion Detector Head.
3. Keep Solar Panel clean and allow unit to charge in full
direct sunlight for 3 days with the Power Switch OFF.
Light stays
“ON”.
Frequent changes in
heat being detected.
Check sensing area for possible heat sources
such as air vents, vehicles or objects in wind.
Relocate the Motion Detector Head if needed.
Light turns ON
and OFF.
1. Changes in heat are being
detected from a fixed heat
source or moving object.
2. Sudden temperature change
due to storms or high winds.
1. Check sensing area for possible heat sources
such as air vents, vehicles or objects in wind.
Relocate the Motion Detector Head.
2. Turn Power Switch “OFF” until storm
passes. Mount in a sheltered location.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect Battery and Charger power supply before service.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Reference UPC 193175434074.