ASTRO DEVICES SkyWatcher Dobsonian User manual

.""
Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
1"
SkyWatcher Dobsonian 6-16” Telescop es:
Encoders Installation
Please"make"sure"that"you"have"all"the"parts"included"in"the"kit:"
"
Specifications:-
Azimuth"Encoder"resolution:"8192"steps"per"revolution"
Altitude"Encoder"resolution:"8192"steps"per"revolution"
Current"consumption:"10mA"–"Azimuth"encoder,"10mA"–"Altitude"encoder"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"

Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
2"
"
Azimuth encoder installation
Please"remove"the"OTA"from"the"base."Then"remove"the"azimuth"pivot"bolt."
"
"
You"will"find"a"plastic"insert."You"need"to"remove"it"and"replace"it"with"the"bushing"supplied.""
"
You"will"need"the"following"parts"for"the"next"step:"
"
"

.""
Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
3"
Insert"the"bushing"provided"and"push"it"into"the"hole."You"need"the"washer"and"the"pivot"bolt:"
"
"
Put"the"new"pivot"bolt"into"the"bushing:"
"
"
Now"turn"the"base"around"or"put"the"whole"base"on"a"side:"
"
"
"

Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
4"
Now"thread"the"mounting"plate"onto"the"pivot"bolt"until"the"plate"cannot"be"rotated:"
"
"
Now"you"need"to"drill"a"small"hole"using"a"1.5-2mm"drill"bit:""
"
Drill"three"holes"–"for"each"screw."

.""
Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
5"
You"now"need"a"screwdriver"and"three"screws"for"mounting"the"plate:"
"
Use"the"screwdriver"to"fix"the"plate"in"place:"
"
Tighten"two"set"screws"using"the"supplied"Allen"key"(make"sure"that"the"rocker"box"can"still"rotate"
freely"before"tightening"the"set"screws):"
"

Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
6"
"
Now"you"need"the"following"parts:"
"
Put"the"tangent"arm"on"the"pivot"bolt:"
"
You"will"need"to"install"the"anchor"bolt:"
"
"

.""
Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
7"
Mark"the"position"of"the"anchor"bolt’s"base"with"a"pencil:"
"
"
Unscrew"the"anchor"bolt"from"its"base."Drill"holes"for"screws."Use"the"supplied"screws"to"install"the"
base"of"the"anchor"bolt:"
"

Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
8"
"
"
And"screw"the"anchor"bolt"back"in"place:"
"
"
"
"
"
"
"
"

.""
Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
9"
You"will"need"the"following"parts"for"the"next"step"(most"of"them"are"in"the"box"with"the"encoder):"
"
"
"
Use"the"spacer"to"slide"the"white"shaft"adapter:"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"

Copyright"©"2022,"Astro"Devices."All"rights"reserved.""
10"
Install"the"black"shaft"adapter"over"the"white"adapter:"
"
And"push"it"down:"
"
Put"the"encoder"base"plate"and"start"threading"the"screws"but"do"not"tighten"them"yet:"
"
"