Astronergy CHSM5001T User manual

CHSM5001T Thin-Film Photovoltaic Module Installation Guide (Rail)
Introduction
This document provides detailed instruction and valuable safety information regarding
installation, electrical connection and maintenance of ASTRONERGY Thin Film Photovoltaic
(TFPV) modules. Before installing a Thin Film photovoltaic system, the installer should
become familiar with the mechanical and electrical requirements. All instructions should be
read and understood before attempting installation. The installer should conform to all the
safety precautions in the guide when installing the module. Keep this guide in a safe place for
further reference.
Warning
This Photovoltaic Module produces electricity when exposed to the sun or other light sources.
For your safety and the safety of others, please read the entire safety and installation
instruction manual carefully prior to product installation. Also, carefully read the module data
sheet provided with this product. Determine local permitting, installation, and inspection
requirements before installing module(s). The manufacturer assumes no liability for damages
incurred due to non-compliance of these instructions. Please also observe the instructions for
the other components which make up the total PV system.
Product Information
1. Electrical Characteristics
Table 1: Electrical Characteristics
Pmax(W) Nominal Initial
Vmp(V) Imp(A) Voc(V) Isc(A) Voc(V) Isc(A)
100 84.20 1.188 127.1 1.499 132.9 1.546
105 87.45 1.199 127.1 1.519 132.9 1.546
110 89.46 1.230 129.1 1.519 134.9 1.566
115 92.70 1.240 132.1 1.529 138.0 1.576
120 94.44 1.269 133.1 1.529 139.0 1.576
Application Class(IEC61730):A; Protection Class II
Maximum over-current protection rating:3A
The module electrical ratings are measured under Standard Test Conditions (STC) of 1 kW/m2
irradiance with AM 1.5 spectrum and a cell temperature of 25 °C. ASTRONERGY modules
deliver specific electrical characteristics as shown above.
Page 1 of 8
A photovoltaic module may produce more current and/or voltage than reported at STC. Sunny

Page 2 of 8
and reflection from snow or water can increase current and power output. Therefore, the
values of ISC and VOC marked on the module should be multiplied by a factor of 1.25 when
determining component voltage ratings, conductor amperage, fuse sizes, and size of controls
connected to PV output.
2. Physical specifications
Table 2: Physical specifications
Module type Tandem junction
Cell type Amorphous/microcrystalline Silicon
Junction type P-i-N
Encapsulation Polyvinyl Butyral（PVB）
Superstrate 3.2mm float glass
Substrate 3.2mm tempered glass
Connector MC4 compatible connector
J-Box IP rating IP65
Cable length Min 750mm
Max load 30lb/ft2
Cable cross area 12AWG
Bypass diode
Max current 3A
Max voltage 1000V
Dimensions
Length(mm) 1300+0/-1
Width(mm) 1100+0/-1
Thickness(mm) 7.16mm (without junction box)
Weight 27.5kg
Max system voltage 600VDC

3. Module parts list
Pos. Qty. Item
1 1’100×1’300 Front glass
2,3 0.3 to 0.5g Silver Conductive Glue
5,6 2×1.26m Solder Strings (long)
7 100g White Paint
8 1.5sqm PVB
9 1’100×1’300 Back glass
10 1 pcs Adhesive compound
11 1 pcs PV Junction box with
bypass diode
13 1 set Mounting rails
Figure 1. Parts list of Astronergy thin film PV module
Safet
y
Instruction
zInstalling solar photovoltaic systems may require specialized knowledge and appropriate
technical skills. Therefore installation should be performed only by qualified persons.
zThe installer should assume the risk of all injury that might occur during installation, for
example, the risk of electric shock.
zOne individual module may generate DC voltages greater than 130 volts when exposed
to direct sunlight. Contact with a DC voltage of 130V or more is potentially hazardous.
zDisconnecting wires connected to a module that is exposed to sunlight may result in an
electric arc. Such arcs may cause burns, start fires, or otherwise create problems.
Therefore be extremely careful!
zKeep children well away from the system while transporting and installing mechanical
and electrical components.
zCompletely cover the module with an opaque material during installation to keep
electricity from being generated.
zDo not wear metallic rings, watchbands, ear, nose, lip rings, or other metallic devices or
jewelry while installing or troubleshooting photovoltaic systems.
zUse only insulated tools that are approved for working on electrical installations.
zAbide by the safety regulations for all other components used in the system, including
Page 3 of 8

wiring and cables, connectors, charging regulations, inverters, storage batteries and
rechargeable batteries, etc.
zDo not attempt to disassemble the module, and do not remove any attached nameplates
or components.
zDo not use mirrors or other magnifiers to artificially concentrate sunlight on the module.
zWhen installing the system, abide by all local, regional and national statutory regulations.
Obtain a building permit where necessary.
Module Installation
Safety Information
zAlways observe the instructions and safety precautions for the module to be installed.
1. Do not lift the module by grasping the module’s junction box or electrical leads.
2. Do not stand or step on the module.
3. Do not drop modules or allow objects to fall on modules.
4. To avoid the breakage of the glass of the module, do not place any heavy objects on
the module.
5. Do not set the module down hard on any surface.
6. Inappropriate transport and installation may break the glass of the module.
7. Avoid any sharp objects (knife, rock etc) scratching either surface of the module.
zThe module should face true south in northern latitudes and true north in southern
latitudes.
zFor detailed information on the best elevation tilt angle for the installation, refer to
standard solar photovoltaic installation guides or a reputable solar installer or systems
integrator.
zThe module should not be shaded at any time of the day.
zDo not use module near equipment or in locations where flammable gases can be
generated or collected. No attempt must be made to drill holes in the glass surface of the
module. Doing so will void the warranty.
zModules must be securely attached to the mounting structure.
zPV modules are exposed to a wide range of mechanical conditions, so that surface
stress may occur. Due to the different thermal coefficient of glass and metal structures,
thermal stress can occur as a result of the module’s outdoor exposure. DIN 1055 sets
basics for the planning of a structural framework regarding building structures and must
be taken into account.
zThe recommended standoff height is 20 cm.
Page 4 of 8

Mounting Instructions
Figure 2 shows one of the recommended mounting configurations of Astronergy TFPV
modules with rail, but other mounting options are also possible. As shown in the figure,
each pair of modules is supported by a structure consisting of two tilted beams (1), two
vertical supports (2) and two horizontal beams (5). The module is secured to the
structure by four mounting bolts, two on each of the supporting rails which are securely
attached to the module by silicone adhesive. The details of mounting the module to the
supporting structure are shown in Figure 3. A T-head M8 bolt with a bracket is used to
fasten the rail to the C-shape horizontal beam. The distance from each mounting point to
the nearest end of the rail is 313+/-2 mm. The nuts should be tightened with a torque
wrench to 35 N-m.

6
5
43
2
1
Figure 2: Mounting configuration
Tilted support. 2) Hexagon bolt M12, flexible washer, nut. 3) Vertical support beam.
4) Mounting rail. 5) Horizontal support. 6) Bracket.
Page 5 of 8


Figure 3: One of the four mounting points. The module is secured to the C-shape horizontal
beam by four M8 T-head bolts and nuts with serrated washers. The distance from each
mounting point to the nearest end of the rail is 313+/-2 mm.
The following precautionary steps are recommended when mounting the module to the
supporting structure.
1. The mounting assembly and the undercarriage must be appropriately dimensioned
and adapted to the in-situ environmental conditions so that the admitted maximum
bending/deformation does not exceed one one-hundredth of the edge length of the
module (L/100) (13 mm or 11 mm, respectively). No buckling/twisting of more than 30
mm across the module diagonal should be allowed.
2. Modules must be stead-fastened and in a durable elastic bedding. All direct contact of
the glass/solar module with metal parts of the substructure must be prevented.
3. The module should be operated under stress- and force-free conditions.
4. Accumulation of water at the solar module must be prevented; as it may cause
corrosion on the panels and on the adhesive bonding (PVB foil between front and
back glass). It can also cause glass blinding.
5. In dimensioning the undercarriage, particular care should be taken of the various
thermal coefficients for each material.
6. Observe the specified fixation points at the approved mounting assemblies
(tightening torque for screws, positions of the drilled holes).
Page 6 of 8

zDo not use modules of different configurations in the same system.
Electrical Installation
zThe module is supplied with connectors for the electrical connections of the system.
zConnector
1. Modules may be connected in series and/or parallel to achieve the desired electrical
output as long as certain conditions are met. The definitive number of parallel
connected modules depends on the plant topology (inverter sizing according to
known practice, protection means, etc). If there are no any particular voltage
protections, no more than four modules are to be series connected. Furthermore, the
maximum reverse current is 3A. Using a blocking diode or fuse in the combiner box is
recommended for reverse current protection when more than three strings are
connected in parallel.
2. IMPORTANT: for optimal performance, modules must only be used in
configurations where the negative polarity of the PV module is connected to
ground (use of inverters with transformers with negative grounding). Failure to
comply with this requirement will reduce the performance of the system and void the
warranty for the modules. Only connect series solar power modules of the same type
and power category. It is not necessary to open the connector box with cables
connected at the factory for electrical switching of the solar power modules.
3. The plugs are marked with the respective polarity (see Figure 4). The MINUS pole is
minus-coded, the PLUS pole is plus-coded.
Plus Minus
Figure 4: Plugs
Page 7 of 8

Maintenance
Page 8 of 8
the following maintenance in order to ensure optimum performance of
th
ning. A mild, non-abrasive cleaning agent can be used to
nnections every six months to verify that
used in the system, such as
support rails, charging regulators, inverters, batteries, etc.
zWe recommend
e module:
1. Clean the glass surface of the module as necessary. Use only water and a soft
sponge or cloth for clea
remove stubborn dirt.
2. Check the electrical and mechanical co
they are clean, secure and undamaged.
zIf any problems arise, have them investigated by a competent specialist.
zObserve the maintenance instructions for all components