Asus P5LD-MR - Motherboard - Micro ATX User manual

Motherboard
P5LD-MR

ii
E2519
First Edition
June 2006
Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or
altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the
serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS,
ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identication or
explanation and to the owners’ benet, without intent to infringe.

iii
Contents
Notices ................................................................................................vii
Safety information .............................................................................viii
About this guide.................................................................................. ix
Typography .......................................................................................... x
P5LD-MR specications summary........................................................ xi
Chapter 1: Product introduction
1.1 Welcome! .............................................................................. 1-1
1.2 Package contents ................................................................. 1-1
1.3 Special features .................................................................... 1-2
1.3.1 Product highlights ................................................... 1-2
1.3.2 Innovative ASUS features ....................................... 1-4
Chapter 2: Hardware information
2.1 Before you proceed .............................................................. 2-1
Onboard LEDs ....................................................................... 2-1
2.2 Motherboard overview .......................................................... 2-2
2.2.1 Placement direction ................................................ 2-2
2.2.2 Screw holes............................................................. 2-2
2.2.3 Motherboard layout ................................................ 2-3
2.2.4 Layout Contents ..................................................... 2-4
2.3 Central Processing Unit (CPU) .............................................. 2-6
2.3.1 Installing the CPU .................................................... 2-6
2.3.2 Installing the CPU heatsink and fan......................... 2-9
2.3.3 Uninstalling the CPU heatsink and fan................... 2-11
2.4 System memory.................................................................. 2-13
2.4.1 Overview ............................................................... 2-13
2.4.2 Memory Congurations ......................................... 2-13
2.4.3 Installing a DIMM ................................................... 2-15
2.4.4 Removing a DIMM.................................................. 2-15
2.5 Expansion slots ................................................................... 2-16
2.5.1 Installing an expansion card .................................. 2-16
2.5.2 Conguring an expansion card .............................. 2-16
2.5.3 Interrupt assignments........................................... 2-17
2.5.4 PCI Express x16 slot ............................................. 2-18
2.5.5 PCI Express x8 slot ............................................... 2-18
2.5.6 PCI slots ................................................................ 2-18

iv
Contents
2.6 Jumpers .............................................................................. 2-19
2.7 Connectors ......................................................................... 2-24
2.7.1 Rear panel connectors .......................................... 2-24
2.7.2 Internal connectors ............................................... 2-25
Chapter 3: Powering up
3.1 Starting up for the rst time ................................................ 3-1
3.2 Powering off the computer................................................... 3-2
3.2.1 Using the OS shut down function ........................... 3-2
3.2.2 Using the dual function power switch..................... 3-2
Chapter 4: BIOS setup
4.1 Managing and updating your BIOS ........................................ 4-1
4.1.1 Creating a bootable oppy disk .............................. 4-1
4.1.2 AFUDOS utility ........................................................ 4-2
4.1.3 ASUS CrashFree BIOS 2 utility ................................ 4-5
4.1.4 ASUS Update utility ................................................ 4-7
4.2 BIOS setup program............................................................ 4-10
4.2.1 BIOS menu screen ................................................. 4-11
4.2.2 Menu bar ............................................................... 4-11
4.2.3 Navigation keys..................................................... 4-11
4.2.4 Menu items ........................................................... 4-12
4.2.5 Sub-menu items.................................................... 4-12
4.2.6 Conguration elds ............................................... 4-12
4.2.7 Pop-up window...................................................... 4-12
4.2.8 Scroll bar............................................................... 4-12
4.2.9 General help .......................................................... 4-12
4.3 Main menu........................................................................... 4-13
4.3.1 System Time ........................................................ 4-13
4.3.2 System Date ........................................................ 4-13
4.3.3 Legacy Diskette A ............................................... 4-13
4.3.4 Primary, Third, Fourth Master/Slave ..................... 4-14
4.3.5 IDE Conguration .................................................. 4-15
4.3.6 System Information............................................... 4-17
4.4 Advanced menu .................................................................. 4-18
4.4.1 USB Conguration ................................................. 4-18
4.4.2 MPS Conguration................................................. 4-19

v
Contents
4.4.3 Remote Access Conguration............................... 4-20
4.4.4 CPU Conguration ................................................. 4-21
4.4.5 Chipset ................................................................. 4-22
4.4.6 Onboard Devices Conguration............................. 4-24
4.4.7 PCI PnP.................................................................. 4-25
4.5 Power Menu ........................................................................ 4-26
4.5.1 ACPI APIC Support ................................................ 4-26
4.5.2 APM Conguration ................................................ 4-27
4.5.3 Hardware Monitor.................................................. 4-28
4.6 Boot menu .......................................................................... 4-30
4.6.1 Boot Device Priority .............................................. 4-30
4.6.2 Boot Settings Conguration ................................. 4-31
4.6.3 Security................................................................. 4-32
4.7 Exit menu............................................................................ 4-34
Chapter 5: RAID configuration
5.1 RAID conguration ................................................................ 5-1
5.1.1 RAID denitions....................................................... 5-1
5.1.2 Installing Serial ATA hard disks ............................... 5-2
5.1.3 Setting RAID item in BIOS ....................................... 5-2
5.1.4 RAID conguration utility ........................................ 5-2
5.2 Intel Matrix Storage Manager option ROM utility .................. 5-3
5.2.1 Creating a RAID 0 set (striped) .............................. 5-4
5.2.2 Creating a RAID 1 set (mirrored)............................ 5-6
5.2.3 Creating a RAID 10 set (RAID 0 + 1)...................... 5-7
5.2.4 Creating a RAID 5 set (parity) ................................ 5-8
5.2.5 Deleting a RAID set ............................................... 5-10
5.2.6 Resetting Disks to Non-RAID................................. 5-11
5.2.7 Exiting the Intel Matrix Storage
Manager utility ...................................................... 5-11
5.2.8 Rebuilding the RAID............................................... 5-12
5.2.9 Setting the Boot array in the BIOS Setup utility... 5-13
5.3 LSI Logic Embedded SATA RAID Setup Utility .................... 5-14
5.3.1 Creating a RAID set............................................... 5-15
5.3.2 Adding or viewing a RAID conguration................ 5-21
5.3.3 Initializing the logical drives .................................. 5-24
5.3.4 Rebuilding failed drives ......................................... 5-29

vi
5.3.5 Checking the drives for data consistency............. 5-31
5.3.6 Deleting a RAID conguration ............................... 5-34
5.3.7 Selecting the boot drive from a RAID set ............. 5-35
5.3.8 Enabling the WriteCache....................................... 5-36
5.4 Global Array Manager.......................................................... 5-36
Chapter 6: Driver installation
6.1 RAID driver installation.......................................................... 6-1
6.1.1 Creating a RAID driver disk ..................................... 6-1
6.1.2 Installing the RAID controller driver ........................ 6-3
6.2 LAN driver installation ........................................................ 6-11
6.2.1 Windows®2000/2003 Server .............................. 6-11
6.2.2 Red Hat®Enterprise ver. 3.0................................. 6-12
6.3 VGA driver installation ........................................................ 6-13
6.3.1 Windows®2000/2003 Server .............................. 6-13
6.3.2 Red Hat®Enterprise ver. 3.0................................. 6-14
6.4 Management applications and utilites installation .............. 6-15
6.4.1 Running the support CD........................................ 6-15
6.4.2 Drivers menu......................................................... 6-15
6.4.3 Management Software menu ................................ 6-16
6.4.4 Utilities menu ........................................................ 6-16
6.4.5 Contact information.............................................. 6-17
Appendix: Reference information
A.1 Intel®EM64T......................................................................... A-1
A.2 Enhanced Intel SpeedStep®Technology (EIST) .................... A-1
A.2.1 System requirements.............................................. A-1
A.2.2 Using the EIST......................................................... A-2
A.3 Intel®Hyper-Threading Technology ...................................... A-3
A.4 Block diagram ....................................................................... A-4

vii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
The use of shielded cables for connection of the monitor to the graphics
card is required to assure compliance with FCC regulations. Changes
or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.

viii
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal
cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
• Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
• Seek professional assistance before using an adapter or extension
cord. These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you
are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact
a qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully
read all the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a
qualified service technician or your retailer.
The symbol of the crossed out wheeled bin indicates that the product
(electrical and electronic equipment) should not be placed in municipal
waste. Check local regulations for disposal of electronic products.

ix
About this guide
This user guide contains the information you need when installing and
conguring the motherboard.
How this guide is organized
This manual contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
• Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to
perform when installing system components. It includes description of
the switches, jumpers, and connectors on the motherboard.
• Chapter 3: Powering up
This chapter describes the power up sequence, the vocal POST
messages, and ways of shutting down the system.
• Chapter 4: BIOS setup
Tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
• Chapter 5: RAID configuration
Provides information on RAID congurations for this motherboard.
• Chapter 6: Driver installation
This chapter provides information on RAID and LAN driver installation
for this motherboard.
• Appendix: Reference information
This appendix includes additional information that you may refer to
when conguring the motherboard.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware
and software products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as
warranty yers, that may have been added by your dealer. These
documents are not part of the standard package.

x
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and
greater-than sign means that you must
press the enclosed key.
Example: <Enter> means that you must
press the Enter or Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys
simultaneously, the key names are linked
with a plus sign (+).
Example: <Ctrl> + <Alt> +<Del>
Command Means that you must type the command
exactly as shown, then supply the
required item or value enclosed in
brackets.
Example: At the DOS prompt, type the
command line: format A:/S
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
NOTE: Tips and additional information to help you complete a
task.
IMPORTANT: Instructions that you MUST follow to complete a
task.