Atak AXT2675 User manual

For technical assistance or troubleshooting
please call 1-855-994-2825 or visit www.sibrands.com
This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 132 lbs.See apparatus
instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible
injury.
READ THIS FIRST Read this entire manual! Do not attempt to install this product if you do not understand the instructions.
Contact a qualified mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what
specific wall materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or
damaged parts. Improper installation may result in damage to your TV, property, and personal injury.
Tilting Flat Panel
Wall Mount
Installation Guide
Model: AXT2675
• Supports most 26”-75” Televisions
• Maximum weight capacity: 132 lbs.
• Supports VESA sizes up to: 600x400

Sourcing International Inc. and ATAK are not responsible for personal injury or product
damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of
this product.

Parts and Hardware
WARNING:This product contains small items that could be a choking hazard if
swallowed. Before starting assembly, verify all parts are included and undamaged.
NOTE: Not all hardware included will be used.
M4x12mm
M5x12mm
M6x12mm
M8x25mm
M4x30mm
M5x30mm
M6x35mm
M8x50mm
TV Brackets
x1
M5/M6x17mm M8x22mm
M5/M4 M6
10mm 2.5mm
M8
M6
M5
M4
1-1 Select TV Screws
TV back
Bracket Washer
Bracket
Long Screw
Spacer
No, go to PAGE 3 for detailed combination.
Yes, go to PAGE 3 for detailed combination.
TV back
2
Washers
Spacers
TV Screws
x4
x4
x4
x4
x4
x4
x4 x4
x4
x4 x4
x4 x8
x4
1-2 Need Spacers?
Short Screw
Washer
x1
Highly recommended to add spacers for more
spacing between wall mount and wall.

3
Tips: If you need to combine M8(d/h) screw with 2.5mm spacer(n), you have to remove
the inner circle of Spacer (n).
1-3 Attach the TV Brackets
Screw and washer
Spacer(s), screw and washer
No!

For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B on PAGE 6
<16mm
(5/8") 16"/24"
(406/610mm)
Min. Wood Stud Size:
nominal 2"(51mm)
actual 1 1/2"(38mm)
Min. Wood Stud Size:
nominal 4"(102mm)
actual 3 1/2"(89mm)
Parts and Hardware
Wood Stud Installation
O
4
Center line
Lag Bolt M8x60mm
M8 Washer
x4
x4
Allen Key
x1
Concrete Wall Anchor 4pcs
CAUTION:Do not use in drywall or wood
Socket tool
x1
Wall plate
x1
Use a pencil to mark the
center of the stud.

16"(406mm)
7/32"
(5.5mm)
2.5"(64mm)
CAUTION :To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate
assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on
to the next step.
Go to Step 3 on PAGE 7.
Center line
No!
Use a pencil to mark the center of the
second stud.
Use a pencil to mark the mounting holes
on the wall. Make sure the holes will be
in the center of the stud and are level.
Use 7/32” (5.5mm) drill bit to pre-drill holes at
least 2.5” inches (64mm) deep at the marked
locations.
Use the Lag Bolts (1) and Washers (2) to secure
the Wall Plate to the wall.

Solid Conrete Wall Installation
6
2.5"
(64mm)
Concrete Wall
Anchor
Min.
8"(203mm)
3/8"
(10mm)
3/8"
(10mm)
DANGER
CAUTION :To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate
assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on
to the next step.
No!
WATER LINE ELECTRIC LINE
Use a pencil to mark the
mounting holes on the wall. Use a 3/8” (10mm) drill bit to
pre-drill holes at least 2.5” inches
(64mm) deep at the marked locations.
Insert a Wall Anchor into each
pre-drilled hole and lightly tap it with
a hammer until the Wall Anchor is flush
with the wall.
Use the Lag bolts (1) and
Washers (2) to secure the Wall Plate
to the wall. Make sure the Wall Plate is
level.

132 LBS (60 kg)
Before hanging TV, please conduct "wall plate installation integrity test" first.
7
Pull Ribbon Down
TV
1 2
As the TV swings down and the lower part of the brackets come in contact
with the wall mount plate, secure each bracket to the Mount plate by pulling
down on the attached ribbon (one bracket at a time) to open the spring-loaded
lock. Release each ribbon to close and secure the lock mechanism. Test each
lock by pulling gently upward from the bottom of the TV. If the lock is secure
the TV will not pull upward.
Lock Opens
Release to
Close Lock
Top of Bracket

8
Tilting angle adjustment (0°/-8°):
Pull TV to your desired angle then tighten the 2 Tilting Bolts (one
Bolt on each Bracket) using the Allen key
Loosen
Tighten
0°
-8°

9
Pull down
on the straps
158mm
222mm
MAX:600mm
MIN:75mm
650mm
MAX:400mm
MIN:75mm 420mm
39mm
610mm
0°~ -8°
Using Two People:
Carefully lift the TV
off of the Wall Plate

LIMITED SIX-YEAR WALL MOUNT WARRANTY
We warrant this product to you, the original purchaser at the time of purchase printed on a dated store receipt from
an authorized ATAK retailer and for a period of six-years thereafter that our wall mount product and all it’s parts
and components are free of defects in material and workmanship under normal use. This warranty is subject to
the provisions below. ATAK’s sole obligation and the purchaser’s exclusive remedy pursuant to these warranties
are limited to replacement at ATAK’s sole discretion. There are no other warranties except as expressively set
forth below either expressed or implied, including any warranty of merchantability for any particular purpose.
Should you be missing any of the assembly parts or components (screws, pieces, etc.), please contact the
Customer Support Center to secure a replacement. It is not necessary to bring the unit back to the store. When
calling, please reference the parts list found in the Instruction Manual to help us accurately identify the missing
parts and promptly provide replacements.
Our Customer Support Center is available Monday to Saturday (10:00AM to 7:00PM EST) for technical assistance
or troubleshooting. To contact us please call 1-855-994-2825 or visit www.sibrands.com
This warranty is expressly limited to the replacement of wall mount parts and components described in the parts
list located in the Instruction Manual included with the product.
This warranty applies under conditions of normal use.
This warranty does not cover: any product, which has been subject to damage due to improper assembly or
disassembly, products which were not assembled, installed, used, or maintained in accordance with the product
assembly instructions & warnings, acts of nature, misuse, neglect, accidents, abuse, exposure to elements,
outdoor use, extreme temperature ranges, damage during transit, commercial use, modification of, or to any part
of the product or attachments to the product not approved by ATAK. Also not covered are costs for
assembly/dis-assembly labor, costs incurred in shipping the unit or parts for warranty repair/exchange or any
products purchased from unauthorized ATAK sellers. Under no circumstances shall ATAK, be liable for any loss
(direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage arising out of, or in
connection with, the use of this product. Nor shall ATAK have any responsibility for incidental or consequential
damages resulting from the breach of this warranty including but not limited to inconvenience, purchase or rental
of replacement products, loss of profits or commercial loss.
We reserve the right to request damaged parts or units be shipped to our offices for inspection or confirmation of
any warranty claims.
This warranty does not cover product sold ‘As Is’.
This warranty is valid only to the original purchaser of the Product in the United States and Canada and grants
specific legal rights.

©Sourcing International Inc., 2020
PN: ATAK AXT2675 Rev. 1.0 June 2020