ATake Sonic Reader User manual

Welcome
Thank you for your purchase of the ATake™ Inductive Amplifier. You are on your way to living a life free of wires. But first, please read this user’s guide
carefully for important information concerning operation, performance and safety.
You will find the ATake™ Inductive Amplifier to be convenient and perfect for watching video and operating the touch screen to enjoy a mini multimedia
feast anytime anywhere.
Read the following recommendations before using the ATake™ Inductive Amplifier. Following these you will be able to enjoy our product for many years.
●Keep it dry and don’t take it to damp places to avoid the product’s internal circuit being affected.
●Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort
certain plastic parts.
●Don’t expose the product to cold areas. It may damage the internal circuit board.
●Don’t try to disassemble the product as it may get damaged if you are not professional.
●Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
●Don’t use intensive chemical products or detergent to clean the product.
●Don’t scratch the surface with sharp things.
●Please turn off the product if you don’t use it for a long time.
NOTE:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PACKAGE CONTENTS
• ATake Sonic Reader Audio Amplifier
• Micro USB power cable
• 3.5mm right angle audio cable
• Instruction manual
Care and maintenance
2013.01
www.atake.com
MADE IN CHINA
TYPE: ASP-706
Sonic Reader
Place-n-Play Audio Amplifier

Operating Instructions
1. Loudspeaker 4. Inductive sensing areas 7. ON/OFF switch
2. Working Indicators (Blue) 5. Micro USB charging port 8.
Micro USB charging cable (1.2m)
3. Charging Indicator (Red) 6. AUX (line in) port 9. Right angle audio cable (0.18m)
FIGURE:
Charge your amplier
MAKE SURE THAT YOUR AMPLIFIER IS FULLY CHARGED BEFORE USING IT. A full charge is approximate-
ly 2 to 2.5 hours and plays continuously 4 hours then.
1. Connect to a USB charging cable or use an additional USB to DC adapter (not included) to charge.
2. When the Red Charging indicator turns on, the device is charging.
3. The Red Charging indicator goes off when the device is fully charged.
Broadcast music from your amplier, just Place-n-Play
1. Switch to turn “ON” the amplifier. The BLUE working indicators remain.
2. Turn on the music on your mobile phone, and place it on the inductive area.
3. Start listening to the music.
4. When the battery is low, the BLUE indicators blink continueously and the amplifier turns off automatically in
two minutes. Please charge your amplifier immediately.
5. Please switch to turn OFF the amplifier if you don’t use it for a long time to prolong the battery life.
Connect to other music equipment
Connect to other portable media players to the AUX line-in port on the amplifier using the supplied
cable.
PLEASE NOTE:
This product works perfect with speaker-placement at either side of the diagonal of the mobile
phones. The audio amplification effect of the mobiel phones may be affected or failed for the speaker
position is not in the inductive sensing area.
This product is an inductive audio amplifier, any signal interference sound from the phone will be
amplified. It’s not the product defective. Please re-adjust the phone's reception angle or strengthen
signal receiving in order to achieve a better audio amplification effect.
Troubleshooting
Q: Can not turn on the amplifier
A: Please use the Micro USB charging cable for charging, and then turn on the amplifer again.
Q: Can’t hear sound from the amplifer
A: Check whether your device is properly placed in the sensing area.
5 6 7
DC 5V
AUX ON/OFF
1 2 3
4
8 9