ATC Electrical & Mechanical atc.ie HANDSU User manual

ATC Electrical & Mechanical,
ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland
IE: 01 4678301, UK:0203 564 9164, Email [email protected]
-1-
ATC Dahlia Hand Sanitiser Unit
Installation and Operation Manual
Please read this installation and operation manual carefully before installing the unit.
Always use the same brand of AA battery and replace all batteries at the same time. Old and new batteries
must not be mixed, doing so will damage the operation of the dispenser.
Prior to installation please ensure that the mounting surface of the wall is flat and clean.
The minimum distance from the outlet of the unit to surfaces below the dispenser must be greater than
250mm.
Should the surface be highly reflective - such as polished stone or stainless steel- then the distance between
the outlet and the surface must be increased to be greater than 350mm.
If these minimum distances are not observed the automatic dispenser may operate whilst it is unattended.
Highly reflective objects such as mirrors should not be put in the sensing range under the unit, nor should
they be left on the counter underneath the dispenser.
This automatic dispensing unit must only be used indoors.
These installation instructions should be given to the user and kept in an accessible location after installation.
Children should only use the dispenser under adult supervision to prevent accidents.
Do not throw away wasted batteries. Batteries must be recycled, please contact your local recycling center
for further information.
The unit contains microcomputers, electronic circuitry, motors and valves. Do not splash or immerse in water.
Clean with a soft cloth and neutral detergent. Do not use aggressive cleaning agents, detergents with micro
particles, highly acidic or alkaline cleaning agents as they will damage the surface. Any such damage is not
covered under the warranty. Be especially careful not to damage the sensor window.
IMPORTANT SAFETY INFORMATION
HANDSU

-2-
ATC Electrical & Mechanical,
ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland
IE: 01 4678301, UK:0203 564 9164, Email [email protected]
COMPONENT DIAGRAM AND DIMENSIONS
PACKING LIST
1x ATC Dahlia Automatic Dispenser 1x Mounting Bracket 3x Fixing screws + anchors
1x Locking Key 1x Installation instructions 1x Battery Holder Locking Screw
1x Anti Theft Locking screw
Note: 6x AA 1.5v DC Batteries are required to operate this unit and are not included with the dispenser.
The Mounting bracket is attached to dispenser on arrival, please remove prior to installation. Should any of
the above items be missing from your dispenser, please contact your supplier.
BATTERY INSTALLATION
Prior to installing the ATC Dahlia Auto Dispenser on the wall, remove the battery holder from the base of the
dispenser and install 6 good quality AA batteries; ensure the correct polarity in the battery holder. Once the
dispenser is mounted and the batteries are installed correctly replace the battery holder into the dispenser and
insert the battery holder locking screw and tighten.
When the batteries require replacement the LED indicator will Flash. Ensure the dispenser is kept upright when
replacing spent batteries.

ATC Electrical & Mechanical,
ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland
IE: 01 4678301, UK:0203 564 9164, Email [email protected]
-3-
INSTALLATION
1. Mark the wall using
the mounting bracket
as a template and
ensure the mounting
distances (left) are
observed.
2. Drill the wall and
install the plastic
anchors.
3. Attach the mounting
bracket with the screws
provided.
4. Mount the dispenser onto the
bracket by aligning the 2 clips and
lower onto the bracket.
5. Install the anti-theft screw, then
the battery holder and finally the
battery holder screw.
FILLING AND OPERATION
1. Once the unit is installed on the
wall, insert the locking key and
twist to unlock the cover. Remove
the cover to expose the sealing
cap.
2. Remove the sealing cap and fill
with liquid soap, alcohol sanitiser
or gel and replace the sealing cap.
Press and Hold the Control button
for approximately 3 seconds until
the LED flashes 3 times.
Each long press of the button turns
the unit on or o.
3. To activate the dispenser the user
should put their hand under the
unit until the sensor activates the
dispenser. Each time the dispenser
operates the LED will flash once.
Note: The initial operation may
take three or four operations until
product is dispensed.
Upper Slot
Upper Clip
Lower Slot
Lower Clip
1
2
Anti Theft Screw
Battery Holder
Screw

-4-
ATC Electrical & Mechanical,
ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland
IE: 01 4678301, UK:0203 564 9164, Email [email protected]
SETTING THE DISPENSE AMOUNT
When the unit is turned on (see above), the amount of product dispensed can
be adjusted - default amount is 1.0ml.
To change the amount dispensed press and release the control button; each
time the button is pressed the LED will flash to inform the user what setting it
is on. 1 flash = 0.5ml, 2 flashes = 1.0ml etc.
There are 5 settings corresponding to 0.5, 1.0, 1.5, 2.0, and 2.5ml. After
reaching 2.5ml the next press returns to 0.5ml.
Note:
• Dierent liquid densities will have slight deviation from the above dispense
amounts.
• Each Time the dispenser is powered o, the dispense amount resets to
factory default (1.0ml).
TROUBLESHOOTING
Problem Reason Potential Solution
No LED Indicator
Control PCB Issue Replace the control PCB
Batteries out of power Change for new batteries
Poor contact in battery holder Remove the batteries, clean the contacts and
replace the batteries in the holder
Indicator window dirty Clean indicator window
LED Continuously
flashing Low battery voltage Change for new batteries
LED On without
product supply Sensor is active
Check for reflective objects below unit and
remove them if present,
Check to ensure sensor window is clean
Insucient
product supply
Short product supply time Adjust the amount of product supplied
(See above )
Product is too thick to dispense Change for less Viscous product
Product dried out internally Try to operate with water to clear obstruction
To avoid blockages always prevent debris from entering the fluid container
SPECIFICATION
Power DC9V (6x AA) Sensing Distance 50-90mm (non adjustable)
Storage Volume 700ml Liquid supply 0.5-2.5ml in 5 steps (adjustable)
Dimensions (HxWxD) 220x100x110mm Ambient Temperature 0-45°C
Net Weight 1.1kg Liquid type Liquid, Alcohol Sanitiser, Gel
WARRANTY
ATC Electrical and Mechanical provides a one year limited parts warranty for the Dahlia automatic dispenser
HANDSU as long as the unit has been installed, used and maintained in accordance with the information
provided in this manual.
In order to arrange parts for the dispenser the information listed below is required. It is recommended to
write this information below and keep this instruction manual in a safe place.
Serial Number: Date of Manufacture:
Date of Purchase: Location Purchased: