Atdec AD-TVAC-CM User manual

Installation Guide
AD-TVAC-CM
AD-TVAC-CM Page 1 of 6
REQUIRED TOOLS
AV Cart Camera Mount
COMPONENT CHECKLIST
Upright
Bracket
Camera
Shelf
M5x8
Screw
(x2)
M5x10
Screw
(x2)
M6x10
Screw
(x2)
5mm
Hex Key
M6
Flange
Nut
Washer
(x2)
4mm
Hex Key
Spanner
• Phillips Head Screwdriver
0 - 5kg
(0 - 11lbs)
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Please ensure your preferred device is securely fastened to the mount prior to use or movement.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to assemble this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these
instructions and the consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that AV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and
offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may
be within the stated range. Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or
toys placed on the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.

AD-TVAC-CM Page 2 of 6
COMPATIBILITY

1. Construct the Camera Mount Assembly
A2. Attach the Camera Mount Assembly to the cart
A - FOR AD-TVC-20 CART
AD-TVAC-CM Page 3 of 6
> 4 mm
Attach Camera Shelf Bto Upright Bracket A
with M5 Screws C.
For AD-TVC-70A, loosen the screws on the
pre-installed silver clamp plate using Hex Key D.
Leave a 4mm gap between the clamp plate and
upright bracket.
For AD-TVC-20, AD-TVC-45 and AD-TVC-75,
remove the silver clamp plate completely.
A2.1. Remove the rubber cable management
grommet from the slot on the cart.
A2.2. Determine the two holes needed on
Upright Bracket Ato hold the Camera
Mount Assembly at the desired height.
A2.3. With assistance, hold the Camera Mount
Assembly sideways (as illustrated)
and align the lower of the two holes
with the hole directly above the cable
management slot on the cart.
A2.4. Insert M6 Screw Hwith Washer Jthrough
Upright Bracket A and into the hole on
the cart.
A2.5. Attach M6 Flange Nut Ito M6 Screw H
inside the cart column through the cable
management slot. Tighten using 5mm
Hex Key D.
TIP: Use Spanner Fto support M6 Flange
Nut Iwhilst tightening M6 Screw H.

B - FOR AD-TVC-45 CART
B2. Attach the Camera Mount Assembly to the cart
A3. Secure the Camera Mount Assembly to the cart
AD-TVAC-CM Page 4 of 6
A3.1. Rotate the camera mount assembly to its nal
position and secure it to the top hole on the cart
using M6 Screw H, Washer Jand 5mm Hex Key D.
A3.2. Install your preferred device. Ensure it is secured
using the screw hole on Camera Shelf Bor straps.
B2.1. Fasten the Camera Mount Assembly to the Cart
at the desired height using M5 Screws G, Washers
J and 4mm Hex Key E.
B2.2. Install your preferred device. Ensure it is secured
using the screw hole on Camera Shelf Bor straps.

C3. Attach Camera Mount
C - FOR AD-TVC-70A CART
C2. Remove Top Cap from the cart
AD-TVAC-CM Page 5 of 6
C3.1. Insert the silver clamp plate (attached
to Upright Bracket A) into the top of
the rear mounting channel of the upper
column of the cart.
C3.2. Move the Camera Mount Assembly to the
desired height and secure it by tightening
the screws using 5mm Hex Key D.
C3.3. Install your preferred device. Ensure it is
secured using the screw hole on
Camera Shelf Bor straps.

MAINTENANCE
• Tighten fasteners and check if the cart is secure and safe to use at regular intervals (at least every three months.)
• Please contact your distributor if you have any questions.
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20220503
D - FOR AD-TVC-75 CART
D2. Attach camera mount assembly to cart
C4. Replace Top Cap
AD-TVAC-CM Page 6 of 6
D2.1. Fasten the Camera Mount Assembly
to the Cart at the desired height
using M5 Screws G, Washers J and
4mm Hex Key E.
D2.2. Install your preferred device. Ensure
it is secured using the screw hole on
Camera Shelf Bor straps.