Atdec TH-3060-UFL User manual

TH-3060-UFL Page 1 of 4
Installation Guide
TH-3060-UFL
Large-Medium
TV Articulated Arm
COMPONENT CHECKLIST
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x 100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
• Power drill
• 5mm (0.2”) drill bit
• 10mm (0.39”) masonry
drill bit
• Phillips head screw driver
• 13mm (0.5”) socket
wrench or shifter
A
Arm/Wall
Mount (x1)
B
Mounting Bracket
(x2)
G
Display
Mounting Screw
M8x25mm (x4)
H
Display
Mounting Screw
M8x16mm (x4)
I
Display
Mounting Screw
M6x25mm (x4)
J
Display
Mounting Screw
M6x16mm (x4)
O
5mm/4mm
Allen Key (x1)
D
End Cap (x2)
F
End Cap
Screw (x4)
L
Nylon Anchor
(x4)
M
Washer
(x4)
N
Multiwasher
(x4)
K
Coach Screw
(x4)
C
Top Cap (x2)
E
Locking Block (x2)
WEIGHT RANGE
0 - 35kg
(0 - 77lb)

TH-3060-UFL Page 2 of 4
Top Cap
Top Cap
SLIDE
SLIDE
1. Changing position of Arm on Wall Mount
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Four optional positions
2. Install Arm/Wall Mount to the Wall
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
WALL Coach Screw
WasherEnd Cap
Screw Drilled Hole
End Cap
WALL
2.1 Masonry Wall
3. Attach Top Caps to the installed Arm/Wall Mount
Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
Secure the mounting plate to the wall using the Coach.
Screws and Nylon Anchors supplied.
Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
Secure the mounting plate to the wall using the Coach
Screws supplied.
Note: Use a stud nder to accurately locate the centre
of the stud. Ensure that all screws x securely into stud.
2.2 Timber Stud Wall

TH-3060-UFL Page 3 of 4
TOP
Back of Display
Display Mounting Screw
Multiwasher
Mounting Bracket
Locking Blocks
Back of Display
4. Attaching Mounting Brackets to Display
5. Attaching/Detaching Display to the installed Arm (2 people required)
WALL
Hook the
Display to
the Arm/
WallMount.
HOOK
LOCK
PUSH
DOWN
1
2
3
4
HOOK
1
Pull down both Spring Lock
Ties to open catch.
PULL
DOWN
2
PUSH
DOWN
3
RELEASE
4
The mounting brackets support hole congurations
from 200x100mm to 700x500mm.
6. Attach Locking Blocks to fully secure the Display
Release Spring Lock Ties
to secure Display.
Note: Ensure that Spring
Lock is fully engaged.
Push down Display into catch.

TH-3060-UFL Page 4 of 4
Back of Display
WALL
atdec.com | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20190814
7. Adjust Arm movement if necessary
5mm Allen Key
4mm Allen Key
WALL
+
_90° + _180°
+
_90°
Back of
Display
Socket Wrench
LOOSEN
TIGHTEN
(+kg)
(-kg)
-5°
+15°
+
_5°
8. Adjust tilt and roll if necessary
9. Cable Management
Position your display to the
desired viewing angle using the
angular movement allowed by
the double ball mount.
Depending on the weight of
the Display, it may be necessary
to make adjustments to the
double ball mount. If the display
does not hold its position, or is
too resistant, adjust the tension
plate located at the rear of the
double ball mount.
To adjust the tension plate,
apply half a turn at a time to
each nut. ENSURE NUTS ARE
ADJUSTED EVENLY.
CHECK THE DISPLAY, and then
adjust again if necessary.