Atel J Series User manual

Version 2.0
About your J-Series CPE
The J-Series ODU (Outdoor Unit) is specially
designed to be installed outside (like on a roof) over
the pole or a wall. That helps ODU to receive better
4G-LTE signals and feed them into the home or
internal living space via an Ethernet cable using the
POE feature.
Quick Start Guide
Model: AOL-J912
4G LTE Bands 2/4/5/12/13/14/25/26/66
J Series by ATEL
4G LTE Outdoor CPE
Figure 1. LEDs & Ports Location
1
2
3
4
5
6
7

Package Contents
•J-Series ODU Unit
•Installation Kit
Mounting Bracket
#2 Phillips Head Screws x4
U-Bolt Clamp Set 2 with M6 Nuts x4
Tools not Provided
•POE Injector x1 (110-240V)
•POE Power Cord x1
•Quick Start Guide
Device Ports & LED Interface
Table 1. Port & LED Definitions
1
Ethernet RJ45 Port
Receive Power &
connect with your
computer over
Ethernet via PoE.
5
PWR (Power)
Power LED. LED On
indicates the device
is turned on. LED Off
indicates that the
device is powered off.
2
Reset Button
Pressing this button
helps device
configurations convert
to factory defaults. 6
ETH (Ethernet)
Ethernet LED. LED On
indicates the
Ethernet/LAN
connection is
established. LED Off
indicates the
Ethernet/LAN
connection is not
established.
3
SIM Slot
Regular (2FF) SIM card
needs to be inserted
as directed.
4
RF
Network Signal Bars.
These LEDs indicate
the receiving signal
quality. More LED bars
represents better
signal.
7
SIM
SIM Card LED. LED
On indicates the SIM
card is inserted and
can be detected. LED
Off indicates no SIM
is detected.
Note:
•Use only the provided accessories as mentioned above.
•If you find anything missing from Package contents as listed
above, kindly contact ATEL at [e-mail].

•Mounting Bracket
•#2 Phillips Head Screw x4
•M6 Nut x4
•U-bolt Clamp Set
Helps to affix the ODU with the mounting bracket to a pole.
Installation Kit
Towards
ODU rear panel
Towards Pole/Wall
Helps to attach mounting bracket to ODU rear panel.
NOTE: Tools not included in the installation kit.
PoE Injector + Power Cord
Output 48-56V DC
Input 100-240V AC

1. Unscrew the covers from
the SIM card slot and
Ethernet LAN port on the
bottom panel.
2. This ODU device is
designed to connect to a
4G LTE network. Kindly
ensure that you have an
active LTE SIM card from
your service provider.
Note: Insert Standard SIM card
(2FF) size to SIM slot as directed
with image.
3. Connect an Ethernet cable
to the LAN port on the
bottom panel of this device,
threading it through the
hole on the Ethernet cover.
Note: Must use a 4 pair Ethernet
cable.
4. Tighten both covers on the
bottom panel of the device.
Setting up your J-Series ODU
Install the SIM Card & Connect the Ethernet Cable
Using PoE to Connect J-Series ODU with PC
Power ON your J-Series ODU
•To turn on your device, you need to connect the
Ethernet cable coming from the ODU to the PoE
injector‘s P+D/OUT Port.
•Now connect power cord to PoE injector’s AC/IN Port.
•The Power LED on the ODU should now be on; this
indicates that the ODU is successfully powered ON.
•To connect your ODU to your PC, first turn the
ODU on using the PoE injector.
•Connect your computer/PC with the PoE’s Data/IN
Port using the Ethernet cable. Make sure your
computer’s Ethernet is configured to obtain an IP
address automatically.
Please only use the provided Power adaptor & PoE injector with
the ODU. The use of other incompatible adapters & PoE may cause
damage to your device and void the warranty.
Note: Must use a 4 pair Ethernet cable between ODU & PoE Injector.
2FF SIM
LAN Port
Ethernet Cable

1. Place the ODU outside and facing an open area towards an
eNodeB/ Cell Tower. Obstructions such as concrete walls,
glass partitions or wooden walls affect the transmission and
reception of network signals.
2. Keep the ODU away from household electrical appliances
that produce strong electric or magnetic fields such as dish
satellite antennas.
Note: Tools required during installation: M6 Wrench and #2 Phillips
Screwdriver (tools not included in installation kit).
Installation of your J-Series ODU
To Mount on a Pole
1. Attach the mounting bracket to the rear panel of the
ODU using four M6 mounting nuts.
2. Attach the U-shaped side of the bracket to the pole
using the provided U bolt clamps.
U-Bolts Clamps
Mounting Bracket
#2 Phillips
Head Screw
M6 Nut Head

To Mount on a Wall
Note: Wall Mount tools and installation
kit items are not included.
Fix Mounting Brackets to ODU
1. Use four screws to attach the
mounting bracket to the rear
panel of the ODU.
If required, use screws used to
stack two mounting brackets
together, allowing the ODU
CPE’s angle to be adjusted
horizontally or vertically.
Fix Mounting Bracket to the Wall
1. Place the U-shaped mounting
bracket against the wall in the
desired position and mark the
location for holes.
2. Use a 4mm drill bit to make
four holes approximately
30mm deep, then insert four
wall anchors into the holes.
3. Use four screws to attach the
ODU with mounting bracket to
the wall.
Affix/Align Mounting Brackets
1. Unscrew the screws used to stack two mounting brackets
together. This also helps the ODU CPE’s angle to be
adjusted horizontally or vertically depending upon wall
/pole side mounting bracket installation.
2. Place the mounting brackets over the U-shaped bracket.
Position the ODU CPE at the desired angle and attach it
with four screws.
Screws on
the Wall
Screws on Mounting
Bracket
#2 Phillips
Head
Screws

Installation Completion
Once the installation is complete and the ODU CPE is
connected to your Computer/PC using the PoE injector. You
can now access data services on that Computer/PC. Make sure
all LEDs are lit up on the ODU.
Your installation should resemble the images below.
Changing Your Online Portal Login
Password
You can change the Online Portal login password by going
to Settings > Basic > Management > UI Access Settings.
Once changed, you must use the new password to login to
the portal.
Online Device Management Portal
You can access your ODU J-Series Online Portal to view
device status, change your device settings, and perform
manual software upgrades (for more details, kindly refer to
the device’s User Manual).
Open any web browser and then enter http://192.168.0.1 in
the URL address bar while connected to the J-Series ODU.
Make sure you are connected directly with the PoE
connection or with some network device, such as a WiFi
router/switch.
The default login username & password is ”admin”.
J-Series ODU
LTE Cell Tower
PoE Injector

Optional Add-On’s: Indoor WiFi AP
To bring LTE High Speed data connection to share with
multiple devices over LAN or WiFi, simply connect the J-
Series ODU with our indoor WiFi AP (built-in POE).
You can contact us to learn more about the ATEL Indoor WiFi
AP on our website, https://www.atel-usa.com/.
If you are using other cables or devices that are compatible
with our AOL-J ODU, please refer to their user manual to
connect with our ODU for data services over the LTE
Network. Factory Resetting of Your J-Series ODU
You can reset your ODU to factory default from the Online
Portal or the reset button.
Note: Resetting your ODU will erase all the changes you
have done and boot up with factory default settings.
A. To reset the device from the Online Portal, click
Settings > Basic > Management. Click on “Restore” to
factory default settings.
B. To reset the ODU from the reset button (refer figure 1),
make sure your ODU is powered on. Insert a pin into
the Reset pin hole, push down and hold for 3 seconds.
The device will restore the factory defaults and reboot.
The ODU must have an uninterrupted power supply during Reset.
Any power failure might result in a hardware failure.
Unable to Access Internet?
1. Check that all LEDs on ODU are lit up. If not, refer to
table 1 and check each LED for current status.
2. Make sure your SIM card is active and internet on the
4G-LTE network is accessible/active.
3. Try resetting your ODU.
4. If an issue still exists, kindly contact to your data service
provider.
J-Series ODU
LTE Cell Tower
PoE Injector

Disclaimer:
Certain variations may be present between the device and user
manual description depending on software release or specific
network services. ATEL shall not be held legally responsible for
such deviations, if any, nor for their potential consequences. Data
plan may be required. Coverage subject to network availability.
Limited Warranty:
The full ATEL USA Warranty Policy can be found at www.atel-
usa.com/warranty. On this page you can “Start a Warranty Claim”,
“Check on an Existing Claim” and read our Warranty Policy by
clicking on “ATEL’s Warranty Policy”. Please follow all warranty
instructions available and if you have any questions contact us at
[e-mail].
Our Website: www.atel-usa.com
Contact usat:[e-mail]
© 2022 Asiatelco Technologies, Inc. All Rights Reserved
@AsiatelcoUSA
@ATEL USA
@atel-asiatelco
@ATEL_USA
For More Information: