Atomic G05214W User manual

1
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
1-888-996-2729
FAX: [phone]
[email protected]
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville, IN 47706
When contacting Escalade Sports please provide your model number, date code (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.
Please have your date code when inquiring about parts.
Your Model Number:
Date Code:
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
G05214W
2-G05214W- -WJ

2
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
THREE ADULTS ARE REQUIRED TO ASSEMBLE
THIS ATOMIC 7FT 2-IN-1 FLIP TOP GAME TABLE
IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
Tools Required:
Wrench T1 included with the table
Phillips Screwdriver
Furniture Polish and Cloth
An electric screwdriver is helpful in assembly. However, please set a low torque and use
extreme caution with an electric screwdriver because you could overtighten the hardware
and strip the screws.
Make sure you understand the following tips before you begin to assemble your flip table.
Assembly Tips
DNA,NOITAREPO,YLBMESSALLAWOLLOFDNADAER
OWTTSAELTA.YLLUFERACSNOITCURTSNIYTEFAS
ELBATEMAGSIHTTUPOTDEDEENERASTLUDA
.REHTEGOT
1. Start all bolts by hand before tightening.
2. Some drawings or images in this manual may not look exactly like your product. Please read
and understand the text before starting each assembly step.

3
HARDWARE IDENTIFIER
(To Scale)
P1 - Pool Table (1)
(Red Cloth)
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
P4 - Left Leg (2)
P3 - Right Leg (2)
P2 - Hockey Table
with C1 Blower Motor (1)
All Right Reserved.
H14 - Leg
Leveler (4)
H3 - 3.5 x 32mm Phillips
Washer Head Screw (8)
H1 - 4 x 44mm Phillips
Flat Head Screw (20)
H7-Barrel Nut (8)
H4 - 8 x 28mm
Hex Head Bolt (8)
H6 - 8 x 63mm
Hex Head Bolt (8)
H5 - 8 x 19mm
Flat Washer (28)
H8 - 8 x 200mm Hex Head Bolt (4)
H10 - Male
Pivot Assembly (2)
H12 - M10 x 25mm
Flat Washer (4)
H9 - 4 x 25mm Phillips
Flat Head Screw (6)
H2 - 4 x 38mm Phillips
Flat Head Screw (34)
H13 - M10
Hex Nut (2)
H19 - 4 x 44mm Phillips
Flat Head Screw (24)
H15 - 4 x 12mm Phillips
Round Head Screw (2)
H16 - 3 x 16mm Phillips
Washer Head Screw (14)
(Not to Scale)
(Not to Scale)
H11 - M10
Acorn Nut (2)
H18 - 4 x 44mm Phillips
Washer Head Screw (4)
H17 - 4 x 50mm Phillips
Flat Head Screw (12)
PARTS IDENTIFIER
(Not to Scale)
!
WARNING:
CHOKING HAZARD
Small parts.
Not for children under 3 yrs.
H20 - 3 x 15mm Phillips
Flat Head Screw (4)
T1 - Wrench (1)
(Not to Scale)

PARTS IDENTIFIER
(Not to Scale)
A7 - Red Puck (2)
A6 - Red Striker (2)
A4 - Cue Chalk (2)
A5 - Cue stick (2)
P6 - Left Leg Panel (2)
A1 - Pool Ball Set (1) A2 - Pool Cloth
Brush (1)
A3 - Plastic
Triangle (1)
P16 - Ball Storage Tray (2)
P17 - Outer Apron with
Cord Hole (1)
P10 - Goal Box Panel (2)
P9 - End Frame Panel (2) P12 - End Top Rail
with Corner Caps
Attached (2)
P13 - L-Frame
Lock (4)
P11 - Frame Bottom
Board (2)
P14 - Leg Connecting
Panel (2)
P5 - Right Leg Panel (2)
P20 - Triangle Holder (1)
P15 - Leg Panel
Stiffener (2)
A8 - Striker Felt Pad (2)
ATOMIC
P7 - Goal Box Support
Frame with Curved (4)
!
WARNING:
CHOKING HAZARD
Small parts.
Not for children under 3 yrs.
P18 - Outer Apron without
Cord Hole (1)
P8 - Goal Box Support
Frame (4)
P19S - Small Cue Clip (2)
P19L - Large Cue Clip (2)
P21 - Round Plastic
for Cord Hole (1)
P22 - Screw
Covers (24)
4
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
ACCESSORY IDENTIFIER
(Not to Scale)
P23 - Barrel Nut
Covers (8)
P24 - Cord
Holder (1)
P25 - Female
Pivot Bushing(2)

IMPORTANT NOTE:
Be careful not to strip these screws.
All H1 Screws must be tight - but not stripped.
Steel inserts
nuts must be
on bottom
PARTS REQUIRED
8 pcs - H1 Phillips Flat Head Screw 2 pcs - P3 Right Leg 2 pcs - P11 Frame Bottom Board
8 pcs - H4 Hex Head Bolt 2 pcs - P4 Left Leg 1 pc - T1 Wrench
8 pcs - H5 Flat Washer 2 pcs - P9 End Frame Panel
STEP 1:
Secure P9 End Frame Panel to P11 Frame Bottom Board using H1 Screws as shown in FIGURE 1A.
Attach the assembly from FIGURE 1A to P3 Right Leg and P4 Left Leg by insert H4 Bolts and H5 Washers from inside of
leg as shown in FIGURE 1B. Use T1 Wrench to tighten H4 Bolts. Repeat with other set of legs.
IMPORTANT NOTE: CAREFULLY LIFT UP THE AIR HOCKEY PLAYFIELD AND REMOVE ALL ASSEMBLY
PARTS, BEING SURE TO CHECK ALL INNER TABLE COMPARTMENTS FOR PARTS. FIND A CLEAN
LEVEL PLACE TO BEGIN ASSEMBLY. WE RECOMMEND BUILDING THE TABLE IN THE BOX TOP TO
PROTECT PARTS DURING ASSEMBLY.
FIGURE 1A
H1
P11
P9
FIGURE 1B
5
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
P4
P3
Grooves on this side.
H5
H4
H4
H5
Please note
Pre-Drilled
holes on
both P9 & P11
PARTS REQUIRED
10 pcs - H2 Phillips Flat Head Screw
2 pcs - P14 Leg Connecting Panel
2 pcs - P15 Leg Panel Stiffener
STEP 2:
Install P15 Leg Panel Stiffeners to P14 Leg Connecting Panels using H2 Screws as shown in FIGURE 2.
Important Note: Be careful not to strip these screws. All H2 Screws must be tight - but not stripped.
FIGURE 2
H2
P14
P15
Black laminate
on this side. H2
H2
H2
H2
Please note
pilot holes on
this top.
Please note
Pre-Drilled
holes on
this side.

6
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
PARTS REQUIRED
8 pcs - H5 Flat Washer 8 pcs - H16 Phillips Round Head Screw 2 pcs - P19L Large
8 pcs - H6 Hex Head Bolt 4 pcs - H18 Phillips Washer Head Screw Cue Clip
8 pcs - H7 Barrel Nut 2 pcs - P19S Small Cue Clip 1 pc - T1 Wrench
STEP 3:
With the help of another adult, attach the assembly from STEP 2 (FIGURE 2) to the assembly from STEP 1 (FIGURE 1B)
using H6 Hex Bolts with H5 Flat Washers and H7 Barrel Nuts as shown in FIGURE 3. Do Not Tighten H6 Bolts at this
time. Next, secure P15 Leg Panel Stiffener using H18 Screws as shown in FIGURE 3. Use T1 Wrench to tighten H6 Bolts.
Attach P19S Small & P19L Large Cue Clips to P15 Leg Panel Stiffeners using pre-drilled holes with H16 Screws as shown
in FIGURE 3. Important Note: Be careful not to strip these screws. All H16 & H18 Screws must be tight - but not
stripped.
H5
H6
H18
H6 H5
H18
H7
H16
P15
P14
FIGURE 3
Assembly from
STEP 1.
Assembly from
STEP 2.
P19L
(Large)
P19S
(Small)
P19S
(Small)
P19L
(Large)
FIGURE 4
STEP 4:
Thread H14 Leg Levelers onto each P3 Right Leg and
P4 Left Leg as shown in FIGURE 4.
PARTS REQUIRED
4 pcs - H14 Leg Leveler
P3
H14
P4
H14
P4
H14
H14
P3
IMPORTANT NOTE:
Tighten, But do not overtighten all H6 Bolts.
IMPORTANT NOTE:
Install each P14/P15 (Assembly from STEP 2) by making sure the 5(five)
black barrel nuts are facing inside of table.

7
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
PARTS REQUIRED
6 pcs - H9 Phillips Flat Head Screw 2 pcs - H13 Hex Nut
2 pcs - H10 Male Pivot Assembly 1 pc - P1 Pool Table
2 pcs - H12 Flat Washer 1 pc - T1 Wrench
STEP 5:
Attach H10 Male Pivot Assembly to each end apron using H9 Screws as shown in FIGURE 5 and DETAIL A.
Secure each H10 Male Pivot Assembly with H12 Washer and H13 Nut as shown in FIGURE 5 and DETAIL A.
Use T1 Wrench to tighten each H13 Nut.
Important Note: Be careful not to strip these screws. All H9 Screws must be tight - but not stripped.
IMPORTANT NOTE: BEFORE INSTALLING PLAYFIELD SCREWS - PLEASE BE SURE ALL
PARTS HAVE BEEN REMOVED FROM INNER CABINET AND AIR MOTOR CORD IS BROUGHT
THROUGH THE HOLE IN SIDE PANEL.
Motor Cord
H9 H10
H12 H13
P1
FIGURE 5
DETAIL A
H9
H10 H12
H13
PARTS REQUIRED
24 pcs - H2 Phillips Washer Head Screw
1 pc - P2 Hockey Table
STEP 6:
With the help of another adult, carefully install P2 Hockey Table into P1 Pool
Table using H2 Screws as shown in FIGURE 6.
IMPORTANT, be sure to feed the plug end from the fan motor through
the hole in the side apron. Be careful not to strip these screws.
All H2 Screws must be tight - but not stripped.
H2
H2
P2
FIGURE 6
P1 IMPORTANT NOTE:
Do not run cord through Side Pocket hole.
Use holes beside the Side Pocket.

PARTS REQUIRED
1 pc - P17 Outer Apron with Cord Hole
1 pc - P18 Outer Apron without Cord Hole
STEP 7:
To install P17 Outer Apron with Cord Hole, please feed the cord plug end back inside the hole in side apron.
Carefully insert and sleave P17 Outer Apron with Cord Hole and P18 Outer Apron without Cord Hole as shown in
FIGURE 7.
P17
P18
FIGURE 7
STEP 8:
Feed the plug end again through the hole in the side apron as shown in FIGURE 8A.
Attach P21 Round Plastic for Cord Hole as shown in FIGURE 8B.
Install four (4) pcs H20 Screws on each end of the side apron as shown in FIGURE 8B.
Insert P25 Female Pivot Bushing onto each H10 Male Pivot Assembly on each end of table as shown in FIGURE 8B.
NOTE: The P25 is not permanently attached until STEP #10.
PARTS REQUIRED
4 pcs - H20 Phillips Flat Head Screw 1 pc - P21 Round Plastic for Cord Hole
2 pcs - P25 Female Pivot Bushing
Cord Plug
FIGURE 8A
Cord Plug
FIGURE 8B
8
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
P21
White laminate
face outside.
White laminate
face outside.
IMPORTANT NOTE:
End of P17 & P18 Outer Apron must be
flush with table end apron.
IMPORTANT NOTE: Do not run cord through side
pocket holes. Please use the holes directly beside
the side pocket.
H20
H20
H20
H20
IMPORTANT NOTE:
This hole is offset and
must match this hole.
Note: Pilot Holes
H10
P25
P25

STEP 9:
With the help of another adult, carefully lift the assembly from
STEP 8 (FIGURE 8B) to the assembly from STEP 4 (FIGURE 4)
as shown in FIGURE 9.
PARTS REQUIRED
2 pcs - H11 Acorn Nut 6 pc - H16 Screw
2 pcs - H12 Flat Washer 1 pc - P24 Cord Clip
!WARNING:
THIS STEP REQUIRES THREE OR MORE ADULTS.
Assembly from
STEP 8.
Assembly from
STEP 4.
9
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
STEP 10:
Secure the assembly from STEP 8 (FIGURE 8B) and the assembly from STEP 4 (FIGURE 4) using H16 Screws as shown
in FIGURE 10.IMPORTANT NOTE: Secure P25 Female Pivot Bushing with H16 Screws using Pre-Drilled holes
shown on P9 End Frame Panel. All H16 Screws must be tight - but not stripped.
Secure assembly using H12 Washer with H11 Acorn Nuts as shown in FIGURE 10. Use T1 Wrench to tighten H11
Acorn Nuts.
Peel the backing off P24 Cord Clip and attach to a side of the table as shown in FIGURE 10.
H11 H12
FIGURE 10
H12
H11
3rd adult helps
to insure P25 Female Pivot Bushing
/ H10 Male Pivot
Assembly
slides down
into slot on
each end of
table correctly.
H10
CAUTION:
PINCH POINT!
CAUTION:
PINCH POINT!
Two (2) adults lift
from each side to
install.
FIGURE 9
P24
PEEL & ATTACH
P24
H16
P25P9
H16
IMPORTANT NOTE:
Secure P25 Female Pivot Bushing
with H16 Screws using Pre-Drilled
holes shown on P9 End Frame
Panel.
P25
CAUTION:
PINCH POINT!

STEP 11:
Rotate table approximately 90 degrees as shown. With the help of another adult hold the table in this position to install
P7 Goal Box Support Frames with Curved and P8 Goal Box Support Frames using H1 Screws as shown in FIGURE 11A.
Slide P10 Goal Box Panels between P7 Goal Box Support Frames with Curved on each end of table as shown in
FIGURE 11B. Important Note: Be careful not to strip these screws. All H1 Screws must be tight - but not stripped.
PARTS REQUIRED
12 pcs - H1 Phillips Flat Head Screw 4 pcs - P8 Goal Box Support Frame
4 pcs - P7 Goal Box Support Frame with Curved 2 pcs - P10 Goal Box Panel
10
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
CAUTION! PINCH POINTS
ROTATE TABLE ONLY WITH ADULT SUPERVISION
FIGURE 11A
P7
P8
P8
P7
H1
H1
H1
H1
H1
H1 P7
P8
P8
P7
Groove face
inside.
FIGURE 11B
ATOMIC
P7
P7
P10
Atomic Jelly
logo on this
side. P10
Groove face
inside.
P8 Pilot hole
on this side.

STEP 12:
With the help of another adult, hold the table in this position to install P13 L-Frame Locks to each (2) leg assembly.
Place H5 Washer on H8 Bolt, insert bolt and washer upward through leg assembly, through H5 Washer, through P13
L-Frame Lock, through H5 Washer, and finally thread into bottom side of P12 End Top Rail as shown in FIGURE 12.
IMPORTANT NOTE: DO NOT OVERTIGHTEN H8 BOLTS AS P13 L-FRAME LOCKS MUST BE FREE TO PIVOT.
Repeat with other legs.
Next, Secure the P12 End Top Rail using H17 Screws as shown in FIGURE 12.
Important Note: Be careful not to strip these screws. All H17 Screws must be tight - but not stripped.
Repeat this procedure on other leg assembly.
PARTS REQUIRED
12 pcs - H5 Flat Washer 12 pcs - H17 Phillips Flat Head Screw 4 pcs - P13 L-Frame Lock
4 pcs - H8 Hex Head Bolt 2 pcs - P12 End Top Rail 1 pc - T1 Wrench
11
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
CAUTION! PINCH POINTS
ROTATE TABLE ONLY WITH
ADULT SUPERVISION
FIGURE 12
ATOMIC
H8
H8 H5
H5
H5
H5
P13
P13
H5
H5
P12
H17
H17
IMPORTANT NOTE:
DO NOT OVERTIGHTEN H8 BOLTS
AS P13 L-FRAME LOCKS MUST
BE FREE TO PIVOT.

STEP 13:
Place all L-Frame Locks into closed position to lock table as shown in FIGURE 13A.
Install P5 Right Leg Panel and P6 Left Leg Panel using H19 Screws as shown in FIGURE 13A.
Stick P22 Screw Covers to cover H19 Screws if needed as shown in FIGURE 13B.
Stick P23 Barrel Nut Covers to cover H7 Barrel Nuts if needed as shown in FIGURE 13B.
Repeat procedure at opposite end of table.
PARTS REQUIRED
24 pcs - H19 Phillips Flat Head Screw 2 pcs - P6 Left Leg Panel
2 pcs - P5 Right Leg Panel 24 pcs - P22 Screw Covers
8 pcs - P23 Barrel Nut Covers
12
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
FIGURE 13A
ATOMIC
P6
P5
H19
FIGURE 13B
ATOMIC
P22
P23
P23
P22
Lock
Position
White laminate
on this side.

STEP 14:
Attach P16 Ball Storage Trays at each table end using H3 Screws as shown in FIGURE 14.
Important Note: Please install P16 Ball Storage Trays so the bottom pre-drilled holes for P20 Triangle Holder
face the inside of the tableas shown in DETAIL B.
Attach one P20 Triangle Holder on bottom side of P16 Ball Storage Tray using pre-drilled holes with H15 Screws as
shown in FIGURE 14 and DETAIL B.
Important Note: Be careful not to strip these screws. All H9 Screws must be tight - but not stripped.
PARTS REQUIRED
8 pcs - H3 Phillips Washer Head Screw 2 pcs - P16 Ball Storage Tray
2 pcs - H15 Phillipls Round Head Screw 1 pc - P20 Triangle Holder
13
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
FIGURE 14
ATOMIC
P16
P20
H15
H3
H3
Note: Cue Stick
Storage Clips.
DETAIL B
H15
P20
P16
IMPORTANT NOTE:
Please install P20 Triangle Holder
back far enough on bottom of P16
Ball Storage Tray so it can not be
a trip hazard.
IMPORTANT NOTE:
Please install P16 Ball Storage
Trays so the bottom pre-drilled
holes for P20 Triangle Holder
face the inside of the table.
Pre-Drilled Pilot Holes

WARNING:
LIFTING POINTS:
FOR FINAL PLACEMENT OF FLIP TABLE
PLEASE MAKE SURE ALL FOUR (4) P13 L-FRAME LOCKS ARE IN
LOCK POSITION , THEN FOUR (4) ADULTS LIFT THE TABLE.
ADULTS SHOULD LIFT TABLE BY PLACING HANDS ON EACH SIDE
OF THE LEG AS SHOWN IN FIGURE 15.
14
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
ATOMIC
! !
IMPORTANT!
LIFTING POINT.
IMPORTANT!
LIFTING POINT.
IMPORTANT NOTE:
P13 L-FRAME LOCKS
MUST IN LOCK POSITION.
FIGURE 15

15
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
CAUTION: ROTATING YOUR TABLE
DO NOT ALLOW CHILDREN TO ROTATE THIS TABLE
This table should be rotated by ADULTS only. To release the table bed, open
the frame locks at each corner. Be sure no one is in the way, then SLOWLY
rotate the bed. After rotating the bed, close the frame locks to lock the table.
CARE AND USE OF YOUR TABLE
Congratulations! You have now assembled your game table. Please note the Care
and Use instructions below to insure many years of trouble free use of your game
table.
1. Use only a suitable 120v AC household outlet, and insure the cord is not a
trip hazard.
2. Spray furniture polish is recommended to both protect the hockey play field
and increase the puck speed. Apply and wipe off with the air motor on.
Use spray furniture polish to clean all exterior surfaces of your game table.
3. Use the table brush provided to clean the cloth on the table.
4. You may use a vacuum cleaner with the brush attachment to clean the cloth
on the pool table should it become necessary.
5. This product is intended for INDOOR use only.
6. DO NOT sit, climb or lean on the table.
7. DO NOT drag the table when moving it. This will damage the legs.
8. DO NOT set drinks on the table.
9. The purchase of billiard table cover will help protect and keep your table
clean while not in use.

16
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
PRODUCT PARTS LIST FOR MODEL # G05214W
Key# Part# Description Qty.
05214WJH1
05214WJH2
05214WJH3
05214WJH4
05214WJH5
05214WJH6
05214WJH7
05214WJH8
05214WJH9
05214WJH10
05214WJH11
05214WJH12
05214WJH13
05214WJH14
05214WJH15
05214WJH16
05214WJH17
05214WJH18
05214WJH19
05214WJH20
05214WJT1
05214WJP1
05214WJP2
05214WJP3
05214WJP4
05214WJP5
05214WJP6
05214WJP7
05214WJP8
05214WJP9
05214WJP10
05214WJP11
05214WJP12
05214WJP13
05214WJP14
05214WJP15
05214WJP16
05214WJP17
05214WJP18
05214WJP19S
05214WJP19L
05214WJP20
05214WJP21
05214WJP22
05214WJP23
05214WJP24
05214WJP25
05214WJA1
05214WJA2
05214WJA3
05214WJA4
05214WJA5
05214WJA6
05214WJA7
05214WJA8
05214WJC1
05214WJK1
05214WJM1
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
H18
H19
H20
T1
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19S
P19L
P20
P21
P22
P23
P24
P25
A1
A2
A3
A4
A5
A6
A7
A8
C1
K1
M1
4 x 44 mm Phillips Flat Head Screw
4 x 38 mm Phillips Flat Head Screw
3.5 x 32 mm Phillips Washer Head Screw
8 x 28 mm Hex Head Bolt
8 x 19 mm Flat Washer
6 x 63 mm Hex Head Bolt
Barrel Nut
8 x 200 mm Hex Head Bolt
4 x 25 mm Phillips Flat Head Screw
Male Pivot Assembly
M10 Acorn Nut
M10 x 25 mm Flat Washer
M10 Hex Nut
Leg Leveler
4 x 12 mm Phillips Round Head Screw
3 x 16 mm Phillips Washer Head Screw
4 x 50 mm Phillips Flat Head Screw
4 x 44 mm Phillips Washer Head Screw
4 x 44 mm Phillips Flat Head Screw
3 x 15 mm Phillips Flat Head Screw
Wrench
Pool Table (Red Cloth)
Hockey Table (No Blower Motor)
Right Leg
Left Leg
Right Leg Panel
Left Leg Panel
Goal Box Support Frame with Curved
Goal Box Support Frame
End Frame Panel
Goal Box Panel
Frame Bottom Board
End Top Rail with Corner Caps Attached
L-Frame Lock
Leg Connecting Panel
Leg Panel Stiffener
Ball Storage Tray
Outer Apron with Cord Hole
Outer Apron without Cord Hole
Small Cue Clip
Large Cue Clip
Triangle Holder
Round Plastic for Cord Hole
Screw Covers
Barrel Nut Covers
Cord Holder
Female Pivot Bushing
Pool Ball Set
Pool Cloth Brush
Plastic Triangle
Cue Chalk
Cue Stick
Red Striker
Red Puck
Striker Felt Pad
Blower Motor
Hardware Kit
Owner’s Manual
20
34
8
8
28
8
8
4
6
2
2
4
2
4
2
14
12
4
24
4
1
1
1
2
2
2
2
4
4
2
2
2
2
4
2
2
2
1
1
2
2
1
1
24
8
1
2
1
1
1
2
2
2
2
2
1
1
1

17
© 2013 Escalade Sports For Customer Service Call 1-886-996-2729
All Right Reserved.
This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS
Product (hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a pe-
riod of 90 days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser
that any Product of its manufacture is free from defects in material and workmanship when used
for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE,
IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PROD-
UCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMAN-
SHIP.
WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADESPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may
prove defective under normal use and proper care, and which our examination shall disclose to
our satisfaction to be thus defective, please contact our Warranty Dept.
1-888-996-2729 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-
warranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for
value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF
THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE ABOVE 90 DAY PERIOD. ESCALADE SPORTS
SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES IN-
CURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or
incidental damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other
rights which may vary from state to state.
90 DAY LIMITED WARRANTY