ATOMICX P100B User manual

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
Model: P100B
Pico Projector
USER GUIDE

-1- -2- -3- -4-
-5- -6- -7- -8- -9-

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
Table of Contents
Customer Support ........................................................................................................ 1
1 Introduction ............................................................................................................... 2
1.1 Features ......................................................................................................2
1.2 What's in the Box ...................................................................................... 3
1.3 Product Overview ..................................................................................... 4
1.4 Infrared Remote Control ......................................................................... 5
2 Getting started ........................................................................................................... 5
2.1 Using the Remote Control .......................................................................5
2.2 Turning the Projector On/Off ................................................................. 6
2.3 Adjusting the Focus ................................................................................. 6
2.4 Charging the Projector ............................................................................. 7
3 Home Screen Overview .......................................................................................... 7
4 General Settings ......................................................................................................... 8
4.1 Adjust the Brightness ............................................................................... 9
4.2 Adjust Projection Mode ........................................................................... 9
4.3 Bluetooth Control Pairing ....................................................................... 9
4.4 Connecting to Wi-Fi .................................................................................. 10
4.5 Keystone Correction ................................................................................ 10
5 All Apps ......................................................................................................................... 11
5.1 Youtube ....................................................................................................... 12
6 Google Play .................................................................................................................. 12
7 Files …………………………….....................................……........................................………. 12
8 Projection Sharing …………………………………................................................………. 12
8.1 Airplay – iPhone ........................................................................................ 13
8.2 Airplay – Mac .............................................................................................. 13
8.3 Miracast – Android device ....................................................................... 14
8.4 Wired Connection U Disk ........................................................................ 14
9 Specifications ……………………………………….................................………….………….. 15
FCC Statement ……………………………………….................................………..…..………….. 16

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
Customer Support
For any support or comments concerning our products, please send an email
to: [email protected]
Toll-Free NO: [phone]
Friendly Tips
Congratulations on choosing to buy an Atomicx Pico projector. All products brought to
you by Atomicx are manufactured to the highest standards of performance and safety.
As part of our philosophy of customer service and satisfaction, products are backed by
our 1 Year Warranty. We hope you will enjoy using your purchase for many years to
come.

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
1.2 What's in the Box
Adapter USB CableProjector
OK
Remote Control TripodOTG Cable
Flannelette Bag User Guide Warranty Card

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
1.3 Product Overview
1
2 3
5
4
6
7
12
13
14
15
16
17
8
9
11
10
1. Battery Power Indicator 2. Lens 3. Reset Key
4. Micro SD Slot 5. USB Charge Interface 6. IR Receiver
7. Audio Out 8. Power Key 9. + Key
10. Return Key 11. – Key 12. Focusing Gear
13. Air Outlet 14. Air Inlet 15. Tripod Mount
16. Speaker 17. Anti-slip Mat

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
1.4 Infrared Remote Control
2. Getting started
2.1 Using the Remote Control
Power Key: Press and hold the power key for 3 seconds to turn on the projector,
Press the power key for 3 seconds to turn off the projector.
Menu Key: Press the Menu key to open the menu options in supported apps and
settings menus.
Navigation Key: The Navigation keys on the remote control let you select between the
apps or menu options available.
OK Key: Press the OK key to select an option.
Home Key: Press the Home key to return to the Home Screen.
OK
1. Indicator Light
2. Power Key
3. Navigation Keys
4. Homepage Key
5. - Volume Key
6. Menu Key
7. OK Key
8. Mouse
9. Return Key
10. + Volume Key
1
2
3
4
5
6
7
8
9
10

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
Mouse Key: Press the mouse key to enable the air mouse, a point will be displayed on
the projected screen, by tilting the remote control you can move the mouse pointer.
Press the mouse key when the pointer is over an option you want to select.
Press the navigation key to turn off the air mouse.
Return Key: Press the return key to go to the previous page or menu.
+ / - Key: Use the + and – keys to adjust the volume.
2.2 Turning the Projector On/Off
• Power On
Press and hold the power key on the projector
for 3 seconds to power on the Atomicx P100B
Pico Projector.
• Power Off
Press and hold the power key on the projector
for 3 seconds to power off the Atomicx P100B
Pico Projector.
Alternatively, you can use the power key on the
remote control to power on/off the Atomicx
P100B Pico Projector.
2.3 Adjusting the Focus
Rotate the manual focus gear (12) to adjust the
focus of the projector.

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
2.4 Charging the Projector
Plug the micro USB end of the USB cable into the
micro USB port on the projector.
Plug the other end into the AC adapter;
plug the AC adapter into an AC plug socket.
When charging the Battery Power Indicator
light will light up red.
When fully charged the light will turn blue.
3. Home Screen Overview

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
4 General Settings
Language
Language settings can be adjusted from the general settings menu.
Use the navigation keys on the remote control to choose the language then confirm
the choice by pressing the ok key on the remote.
Home Screen > Settings > General Settings > Language
Date & Time
Date and Time can be set from the general settings menu.
Use the navigation keys on the remote control to choose the date and time settings
then use the ok key to confirm.
Home Screen > Settings > General Settings > Date & Time
Storage Management
The storage management option under the general settings lets you see the internal
storage. Home Screen > Settings > General Settings > Storage management
Application Management
You can access all the applications from the application management menu. Use the
navigation keys on the remote control to choose the application then press the OK Key
to launch the application.
Home Screen > Settings > General Settings > Storage management
Online Upgrade
To check for a later version of the Atomicx projector’s software open the online
upgrade potion from the general settings menu.
Home Screen > Settings > General Settings > Online Upgrade
Factory Setting
To restore the Atomicx projector to the factor defaults open the Factory setting option
from the general settings menu.
A pop up will ask you display. “Do you want to restore Factory Settings” Using the
Navigation keys select Confirm and press ok to restore factory settings, To cancel the

-1- -2- -3- -4-
-5- -6- -7- -8- -9-
option select cancel or press the return key to return to the general settings menu.
Home Screen > Settings > General Settings > Factory Setting
If the projector is turned on and will not respond you can press the Reset Key (3) for
one second to perform a hard factory reset and restore the factory settings.
Warning:
If you restore the factory settings all data stored on the pico projector will be lost and
the device will be returned to its factory default settings.
Be sure to back up any data needed before selecting this option.
4.1 Adjust the Brightness
The projector’s brightness can be selected from the settings menu.
You can choose between Standard mode/Brightest mode.
Home Screen > Settings > Projector Settings > LED Brightness
4.2 Adjust Projection Mode
You can adjust the projection mode from the settings menu.
You can choose between the following projection modes: Standard Front Projection,
Standard Rear Projection, Hoisting Front Projection, and Hoisting Rear Projection.
Home Screen > Settings > Projector Settings > Projection mode
4.3 Bluetooth Control Pairing
Bluetooth settings can be adjusted from the settings menu. You can pair the Bluetooth
controller or other Bluetooth enabled devices.
Home Screen > Settings > Bluetooth Setting
To pair a device to the projector, select the “Scan For Devices” option and then select
the device from the list Available Devices.
Note: If the remote controller can’t be scanned press the “OK” key and “Volume –” key
on the remote for 5 seconds to confirm the Bluetooth mode has been turned on then
scan for devices on the projector.

-1- -2- -3- -4-
-5- -10-
-6- -7- -8- -9-
4.4 Connecting to Wi-Fi
The Atomicx Pico projector has 2.4G and 5G Dual Band Wifi support.
To connect to a Wi-Fi network go to the Wi-Fi settings under the settings menu.
Ensure the Wi-Fi is turned on and then select the desired network from the available
network list.
Follow the screen prompts to enter the Wi-Fi password and connect to the network.
Home Screen > Settings > Wi-Fi Setting
Note: After you enter the Wi-Fi password, click next on the on-screen keyboard to
connect. Alternatively, click back on the remote control and then click the connect
button on the screen.
4.5 Keystone Correction
The Atomicx P100B Pico Projector has manual Keystone correction. This can be
adjusted from the settings menu. This lets you set the trapezoid correction.
You can adjust the coordinates of the four points (X,Y) of the rectangle through the
navigation keys on the remote control.

-1- -2- -3- -4-
-5- -11-
-6- -7- -8- -9-
Use the Navigation keys on the remote control and follow the onscreen prompts to
adjust or reset the keystone correction.
Home Screen > Settings > Keystone Correction
5. All Apps
To view all the apps installed on the Atomicx P100B Pico Projector
projector open All Apps from the Home Screen.
The projector comes with Apotide TV app Store, Hulu, Netflix, and Amazon Prime Video
apps pre-installed. These are listed in the All Apps folder accessible from the Home
Screen.
Note: When using Netflix the navigation buttons on the remote control will not work.
Please use the air mouse function on the remote control (see user manual 2.1) or
connect a mouse via the USB OTG cable or with Bluetooth.
X: 0
Y: 0
"OK" Check positon; "UP / DOWN / LEFT / RIGHT" Adjust angle; "MENU" Reset status; Back Come back.

-12-
OK
5.1 YouTube
The projector comes with the YouTube app pre-installed. You can open YouTube
directly from the projector's home screen.
Home Screen > YouTube
6. Google Play
The Atomicx P100B Pico Projector comes with Google Play pre-installed, You can open
this application from the home screen to download and install additional apps and
software.
7. Files
You can use the Files option from the home screen to open the file manager where you
can view and manage the files and apps on the projector, SD card, USB drive or local
network connected to it.
8. Projection Sharing
Connecting your Atomicx P100B Pico Projector to another device.

-13-
8.2 Airplay – Mac
AirPlay: off
AirPlay To:
XXX-XXXXXX-XXX
Open Displays Prefer…
FileFinder Edit View Go Window Help Tue 12:00 PM97%
8.1 Airplay – iPhone
1a. With Projector Connected to Wi-Fi
• Select the IOS screen sync option from the Home Screen.
• Select the iPhone option.
• Enter the iPhones Setting > Wi-Fi, then connect the iPhone
to the same Wi-Fi network as the projector.
Note: on devices running iOS 11.0 or above the Airplay function
is listed as Screen Mirroring.
1b. Without Projector connected to Wi-Fi, Using Mobile Hotspot.
• Enter the iPhones Setting > Personal Hotspot > Open Hotspot
• Connect the projector to the hotspot.
( See 4.4 Connecting to Wi-Fi)
2. From the Phone’s settings click the Airplay option.
3. Choose “xxx-xxxxxx-xxx” then open “Mirroring”.
The projector will now be connected to the iPhone sharing the same screen display.

-14-
8.3 Miracast – Android device
NOTE: Ensure the Projector and your Android device are connected to the same Wi-Fi
network.
1. Open the settings on your Android device. Click “more wireless settings”
2. Open “Cast Screen” Searching and connecting.
3. For some Android devices open the shortcuts menu,
look for the “screen sharing/mirroring/screen projection display/ WLAN Display/
Wireless Display/ Multi-Screen/Smart View, search and connect to the device.
If you can’t find the miracast function please contact customer service.
8.4 Wired Connection U Disk/Micro SD Card
1a. How to read the U Disk
• Connect the USB OTG cable to the Micro USB interface of the Projector.
• Connect the U disk to the other end of the USB OTG interface.
1b. How to read the Micro SD Card
• Insert the micro SD card into the micro SD card reader on the Projector.
2. Click in the file option from the home screen. Navigate the data using the
remote controller.
1a. With Projector Connected to Wi-Fi
On the Mac, click the Wi-Fi settings “ ”.
Connect the Mac to the same Wi-Fi network as the projector.
1b. Without Projector Connected to Wi-Fi
On the Mac, click the Wi-Fi settings ” “. Choose “AndroidAP” and connect.
2. Click ” “ , choose “xxx-xxxxxx-xxx” and the projector will now be connected to
the mac sharing the same screen display.

-15-
Max Brightness
Resolution
Display Ratio
Contrast
Projection Distance
Throw Size
Wi-Fi
Bluetooth
Battery
Battery Life
Micro SD Card
Power DC
Operating System
Supported Wireless Protocols
Weight
Product Size
Working Temperature
100 Lumen
854x480
16:9
1000:1
0.2 to 3 M
1M/37.8 Inch, 2M/75 Inch, 3M/110 Inch
IEEE 802.11a/b/g/n/ac, 2.4G / 5G Dual Band
4.1
4200mAh Polymer Battery
130 Minutes
Supports up to 32GB Max
5V 2A
Android 7.1
Airplay / Miracast
290g (12oz)
75x75x44mm ( 2.95x2.95x1.73inch)
0°C to 30°C (32°F to 86°F)
9. Specifications

-16-
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Warning: changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Pico Projector
P100B
P100BI19UMEN-01