ATON Ra.Store-K User manual

Installation of the Wi-Fi
communication card
Rev. 1.01
Ra.Store-K

2
Follow the below procedure to modify the communication mode of storage system
model Ra. tore-K and to install the Wi-Fi ATN813 communication card:
1. Switch the storage system off according to the following procedure:
Open FB1, FPV1, FPV2 and witch OFF QG1, QE2 and QE21 on the equipment’s side.
2. Remove the plastic carters:
Unscrew the two screws that keep the upper panel fixed to the structure. Remove the
panel.
The 3 coloured side panels are fixed to the structure as follows:
- In the upper part: by means of horizontal pins that are pressure-inserted in
their guides
- In the lower part: by means of hooks inserted in specific holes in the structure.
PART’ NAME
PART’ TATU

3
Gently pull the panels’ upper part so that the pins get out of the guides. Lift the panel.
The control card is located in the equipment’s upper part. Disconnect the connector
on the “flat ribbon” that feeds the external led column as indicated in the following
picture.

4
3. Remove the GPRS communication card and install the i-Fi communication
card:
1) Remove the plastic protection on the card’s back by unscrewing the two nuts
that keep it fixed to the display card.
2) Unscrew and disconnect the golden connector that connects the aerial’s
coaxial cable to the communication card.
3) Remove the GPR ATN811 card from slot n.5 on the back of the display card.
if ATN Wi-Fi card is already installed
goto paragraph 4

5

6
4) Insert Wi-Fi ATN813 card in slot n.1.
5) Connect the coaxial golden connector to the plug on the Wi-Fi ATN813 card,
which has been inserted in lot 1 of the display card
6) Replace the plastic protection by screwing the two nuts that keep it fixed to
the display card.
7) Reconnect the “flat ribbon” connector that feeds the equipment’s led
column.
8) Reinstall the carters:
et the three side panels in the lower guides. In the upper part, make sure to
insert the pins in the relevant guides. Relocate the upper panel and screw the
two screws keeping it fixed to the structure.

7
4. Modification of the system’s i-Fi connectivity
The picture here below show the display and the system’s keys.
Press the “arrow up” key until displaying the screen with numerical data.
hile pressing the orange-circled key, press the “Enter” key (green).
This procedure allows accessing the main-configuration menu.

8
Move the cursor beside the “ i-Fi” writing using the “arrow up” and “arrow down”
keys. Press “ENTER”.
The following picture shows the Wi-Fi submenu:
The cursor is positioned next to the writing “Start”; press the “ENTER” key to enable
the Wi-Fi communication.
The first writing of the Wi-Fi menu changes from “WIFI OFF” to “WIFI ON” as shown
in the following picture:
By pressing the “arrow up” or “arrow down” keys, move the cursor beside the writing
“Configure” and press “ENTER”.

9
The following screens will appear after a few seconds:
meaning that the Wi-Fi communication is enabled.
In order to complete the configuration procedure, use any device with a Wi-Fi
connection (here below referred as PC) and Web Browser:
1. Connect the PC to the Wi-Fi net Ra_Config (Pic. 5).
Pic. 5
2. Launch the PC’s Web Browser
3. Enter 192.168.1.1 in the location toolbar. The next picture shows the page
that will open:

10
NOTE: in case it appears a screen with a red box (see following pic) at any point of
the procedure, go back to point 1.

11
4. In the Network Mode field, select Client (Infrastructure) (Pic. 8).
5. Click on the Refresh List key. The module will scan the available nets and will
show the relevant list in Available Access Points (Pic. 8).
6. elect a net; fields Access Point SSID and Security Mode (for Wi-Fi nets with
no password, select “Open”) will be automatically filled. If the list does not
include the desired Wi-Fi net, click on Refresh List for a new scanning.
7. Enter the net’s password in the field Passphrase (tick Show Passphrase to see
the entered password)

12
8. (Optional) the module uses the DHCP as a default. To set a static IP, remove
the tick to Check to enable DHCP and enter a static IP, subnet mask, and
gateway.
9. Click on Save & Reboot to save the settings.
10. Press OK in the pop-up window to exit (Pic. 9) and close the Web Browser.
Pic. 9
11. Access the equipment’s Web page. Wait a few minutes and check that the
screen’s date updates. Repeat the procedure in case it does not update.