ATTO Technology EPCI-UL4D User manual

Installation and Operation Manual
ATTO ExpressPCI UL4S
Single Channel Ultra320 SCSI, PCI-X Host Adapter
ATTO ExpressPCI UL4D
Dual Channel Ultra320 SCSI, PCI-X Host Adapter
ATTO ExpressPCI UL5D
Dual Channel Ultra320 SCSI, PCI Express Host Adapter
ATTO ExpressPCI UL5D LP
Dual Channel Ultra320 SCSI, Low-Profile PCIe Host Adapter
© 2006 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their
respective holders. No part of this manual may be reproduced in any form or by any means without the
express written permission of ATTO Technology, Inc.
9/2006 Document Control Number: PRMA-0325-000MD

ATTO Technology Inc.
Contents
1 SCSI is a key technology for storage 1
SCSI advantages
Glossary
2 ATTO ExpressPCI Ultra320 SCSI solutions 3
Ultra 320 SCSI features
Common features
UL4D, UL4S specific features
UL4D specific features
UL4S specific features
UL5D, UL5D LP specific features
UL5D specific features
UL5D LP specific features
SCSI host adapter selection guide
3 Hardware installation 5
System requirements
Installation
3.1 Cabling and termination ......................................................7
Setting up cables and termination
4 Installing drivers 9
5 Updating hardware flash 10
Use the ATTO Configuration Tool
Use the ExpressPCI BIOS Setup Utility
Appendix A Standards and compliances ............................................i
Appendix B ATTO product guide .........................................................ii
SCSI adapter selection guide
Celerity FC storage adapter selection guide
Appendix C Contact ATTO Technology, Inc. ......................................iv

1
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
1 SCSI is a key technology for storage
Ultra320 SCSI represents the seventh generation of SCSI technology, an I/O interface that increases
performance while maintaining backward compatibility and legacy support.
From its roots in 5 MB/sec. transfer rates, SCSI
has evolved as the leading interface for disk drive
connections in high performance servers. It
features maximum data transfer rates of 320
MB/second, full backward compatibility with
older versions of SCSI protocols and additional
features to improve performance and reliability.
Ultra320 is a powerful storage technology. All
forms of digital content, from e-mail, video, film,
and audio, to streaming video, and imaging, are
driving the unprecedented growth in storage that
pushes the I/O bandwidth, requiring more
advanced interfaces to handle data transfer.
SCSI advantages
• Backward compatible with older versions of
SCSI. Newer adapters will negotiate to the
lower speeds of legacy devices.
• Minimal investment to upgrade technology.
Older equipment may still be used with newer
equipment. Upgrade does not require
replacement of infrastructure.
Exhibit 1-1 How SCSI has evolved.
Glossary
Some terms used in the storage industry are defined below. More information is available through the
ATTO Technology website ( www.attotech.com ) and the SCSI Trade Association ( www.scsita.org ).
Narrow Fast/
Narrow Ultra Ultra/WIDE Ultra2 Ultra160 Ultra320
Data transfer
rates
<5 MB/sec 10 MB/sec 20 MB/sec 40 MB/sec 80 MB/sec 160 MB/sec 320 MB/sec
SCSI protocol SCSI-1 SCSI-2 SCSI-3 SCSI-3 SCSI-3 SCSI-3 SCSI-3
Specification SPI-1 SPI-1 SPI-1 SPI-1 SPI-2 SPI-3 SPI-4
Transfer type Single-
Ended
Single-
Ended HVD
Single-
Ended HVD
Single-
Ended HVD
LVD LVD LVD
Term Definition
ANSI American National Standards Institute
Asynchronous
Information
Protection
AIP: although most Ultra320traffic is sent synchronously and protected by CRC, some
information is still sent asynchronously. AIP implements CRC-level error checking on
asynchronous traffic ensuring end-to-end data integrity.
bit Smallest unit of data a computer can process: a single binary digit with a value of either 0 or 1
byte an ordered set of 8 bits
CRC Cyclic Redundancy Checking, an error-correcting code which calculates a numeric value for
received and transmitted data. If no error has occurred during transmission, the CRC for both
received and transmitted data should be the same.
destination address A value in the frame header of each frame which identifies the port in the node where the
frame is being sent
domain validation Before sending data, domain validation verifies that the physical connection is capable of
handling the negotiated transfer speed. If the system determines that Ultra320speeds are not
feasible, a slower speed is enforced.

2
SCSI is a key technology for storage
double transition
clocking
Increases the data line frequency to equal that of the request signal, allowing sampling on
both the leading and trailing edges of the request signal. Clocking can be set to ensure
compatibility with legacy devices.
flow control The target indicates to the initiator when the last packet of a data stream will be transferred so
that the initiator can flush FIFOs and terminate pre-fetch sooner than previously possible.
Basically, the target warns the initiator that the transfer is almost complete so that it can
prepare for the next transfer while the target completes the current transfer.
host A processor, usually a CPU and memory, which communicates with devices over an interface
HVD High voltage differential: uses two wires, transmitting a signal on one and its inverse on the
other. At the receiving end, the difference between the two signals is measured and
interpreted. Noise on the bus will affect both the signal and its inverse equally, so the
difference between the two lines will remain the same and the noise cannot be misread as a
signal.
initiator device A component which originates a command
LED Light-emitting diode: a type of diode that emits light when current passes through it. Visible
LEDs are used as indicator lights on all sorts of electronic devices.
LVD Low voltage differential. SCSI signalling method that combines the benefits of HVD and
single-ended technologies, allowing longer cabling configurations while consuming less
power than HVD technology.
originator An initiating device; a component which originates a command
packetization Creates information units (IUs) from commands, data, status information, etc. which are
passed as synchronous transfers. Maximizes bus use, minimizes command overhead and
allows multiple commands to be transferred in a single connection
pre-compensation Although SCSI transfer speeds have changed dramatically over the past several generations,
cable specifications have remained constant. Higher speed and frequency signals have a
greater potential for reflection and distortion over distance. Pre-compensation techniques
slightly modify the SCSI signal to reduce the chance of these types of problems.
Quick Arbitration
Select (QAS)
Arbitration
The process of devices negotiating for control of the bus with built-in “quiet times” so that fast
and legacy devices have an opportunity to take control of the bus. A fair, but somewhat
inefficient process, QAS speeds up the arbitration process by eliminating the bus free phase.
When combined with packetization, reduces command overhead and maximizes bus use.
read and write data
streaming
Minimizes data transfer overhead by allowing a target to send one data stream (LQ) packet
followed by multiple data packets. Minimizes overhead of data transfers because the target
can send one data stream packet followed by multiple data packets
receiver The ultimate destination of data transmission; a terminal device
SCSI Small Computer Systems Interface: a processor-independent standard for system-level
interface between a computer and intelligent devices including hard disks, floppy disks, CD-
ROM, printers, scanners, etc.
single-ended An electrical signal protocol that transmits information through changes in voltage. Single-
ended SCSI uses standard TTL signal and ground pairs to transmit information over the SCSI
bus.
training pattern SCSI is a parallel bus technology that is dependent on signals being transmitted on parallel
wires simultaneously. At higher speeds, minute differences in wire lengths and transmission
characteristics could cause problems. Training pattern testing measures these minute
differences and compensates for them.
Vpath™ Technology The ATTO ExpressPCI UL4S with Vpath Technology offers data transfer rates of 320 MB/sec.
With one external connector and one internal connector, Vpath Technology allows both faster
and slower devices to run without impacting the speed of faster devices.
Term Definition

3
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
2 ATTO ExpressPCI Ultra320 SCSI solutions
The Ultra320 SCSI host adapter represents the seventh generation of SCSI technology, an I/O interface
that is committed to increased performance while maintaining backward compatibility and legacy
support. The ATTO ExpressPCI UL4S is a single channel Ultra320 SCSI, PCI-X host adapter, the ATTO
ExpressPCI UL4D is a dual channel Ultra320 SCSI, PCI-X host adapter, and the ATTO ExpressPCI
UL5D and UL5D LP are dual channel Ultra 320 SCSI PCIExpress (PCIe) host adapters.
Today’s computing applications continue to
strain the host PCI bus and storage subsystem. To
bring better performance and reliability to today’s
professional applications, the ATTO ExpressPCI
UL4D and UL4S adapters deliver up to 640
MB/sec. data throughput, and take advantage of
the PCI-X bus interface while the ExpressPCI
UL5D delivers data throughput rates of up to 640
MB/sec. using the latest in PCI bus technology,
PCIe. ATTO ExpressPCI UL4D, UL4S, UL5D
and UL5D LP adapters deliver the high
bandwidth demanded in data-intensive
environments such as real-time and high-
definition video editing, web server and database
engines.
To maximize your attached storage, you may
wish to use RAID, a storage system using
multiple disk drives to improve storage
productivity and efficiency. Instead of using the
RAID functionality built into Windows OS, use
the ATTO Express PowerCenter Utility or
ExpressRAID for the most efficient performance.
Contact your ATTO representative for more
information.
Ultra 320 SCSI features
• Double Transition Clocking
• Domain Validation
• Cyclic Redundancy Check (CRC)
• Packetization
• Quick Arbitration Select (QAS)
• Free-Running Clock
• Read and Write Data Streaming
• Flow Control
• Training Pattern
• Pre-Compensation
• Asynchronous Information Protection (AIP)
Common features
• Supports data transfer speeds of up to 320
MB/sec. per channel
• Supports Ultra320 Specifications including:
• Packetized SCSI
• Double transition clocking
• Quick Arbitration Select (QAS)
• Cyclical Redundancy Checking (CRC)
• Domain Validation (DV)
• Asynchronous Information Protection (AIP)
• Free-running clock
• Flow control
• Advanced Data Streaming (ADS™) provides
controlled acceleration of data transfers.
• Embedded RISC processor for low
overhead
• Bus mastering eliminates CPU processing
time as a bottleneck
• Tagged command queuing allows threads to
be processed efficiently
• Disconnect/reconnect eliminates wait time
between transfers
• Optimized scatter/gather lists
• Backward compatible with legacy SCSI devices
• ASPI (Windows®) compatible
• Automatic and upper-byte termination
• Flash ROM for easy field upgrades
• RAID ready
• Environment and physical specifications
• Operating temperature: 0-45oC
• Humidity: 10-90% non-condensing
• Airflow: 100 LFM (min.)
• Reliability
• MTBF: 150,000 hours
• MTTR: <15 minutes
UL4D, UL4S specific features
• Accelerated PCI bus management
• PCI Bus Master rate of 1-GB/sec.
• PCI-X 1.0a compliant
• PCI 2.2 compliant
• 64-bit/133 Mhz PCI-X (backward compatible
with standard PCI)

4
ATTO ExpressPCI Ultra320 SCSI solutions
• Power
• 0.75 typical/2.0 max. Amps @ + 5.0 /VDC
• 0.05 Amps @ + 12.0 VDC
UL4D specific features
• Two external VHDCI and two internal high-
density 68-pin connectors
• Supports up to 30 SCSI bus IDs (15 per channel)
• Dimensions
• Length: 6.521”
• Height: 4.450”
UL4S specific features
• One external high-density 68-pin connector and
one internal high-density 68-pin connector
• Dimensions
• Length: 6.521”
• Height: 4.200”
UL5D, UL5D LP specific features
• Supports up to 30 SCSI bus IDs (15 per channel)
• PCI Express (PCIe) bus management
• PCI Bus master rate 2-GB/sec.
• PCI-Express 1.0b compliant
UL5D specific features
• Two external VHDCI and two internal high-
density connectors.
• Dimensions
• Length: 7.5”
• Height: 4.376 “
• Power
• 1.61 typical/2.03 max. Amps @ +3.3 VDC
• 0.65 typical/1.46 Amps @ + 12.0 VDC
UL5D LP specific features
• Dual stacked external VHDCI connectors.
• Dimensions
• Length: 6.6”
• Height: 2.713”
• Power
• 0.55 typical/0.9 max. Amps @ +3.3 VDC
• 0.56 typical/0.59 max. Amps @ + 12.0 VDC
SCSI host adapter selection guide
Single Channel Dual Channel-- 2 independent channels
ExpressPCI Ultra 320 ExpressPCI Ultra 320 ExpressPCI Ultra 320
Max. transfer rate 320 MB/sec 640 MB/sec 640 MB/sec
LVD •••
64-bit (PCI) ••
32-bit (PCI) ••
33 MHZ (PCI) ••
133 MHZ (PCI-X) ••
x4 PCIe •
Bus ID support 30 30 30
Part number EPCI-UL4S EPCI-UL5D EPCI-UL5D LP EPCI-UL4D

5
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
3 Hardware installation
Install the ATTO ExpressPCI Ultra320 host adapter and attach your SCSI devices to it using the
instructions below. To get the best performance from your ATTO Express Ultra320 host adapters, use
Ultra 320 SCSI devices.
CAUTIONCAUTION
Remember to back up your system data
before changing or installing hardware.
System requirements
The ATTO ExpressPCI host adapter package
contains the host adapter, the ATTO ExpressPCI
CD and a warranty and registration card. If any
items are missing, contact your ATTO authorized
sales representative.
To install and use the ATTO ExpressPCI UL4D
and UL4S SCSI adapters you need:
• A computer with an available 64-bit PCI-X
expansion slot (preferred) or a standard 32- or
64-bit PCI expansion slot.
• The complete ATTO ExpressPCI SCSI host
adapter package.
To install and use the ATTO ExpressPCI UL5D
and PCI UL5D LP you will need
• A computer with an available x4 ExpressPCI
expansion slot or larger, such as x8 or x16.
• The complete ATTO ExpressPCI SCSI host
adapter package.
CAUTIONCAUTION
ATTO ExpressPCI host adapters contain
components that are sensitive to
electrostatic discharge (ESD). ESD can
cause damage to the ExpressPCI host
adapter. Please follow standard methods
to avoid ESD.
Installation
Remember to back up your system data before
changing or installing hardware.
1 Plan your SCSI device connections.
If connecting both internal and external devices
to the ATTO ExpressPCI SCSI adapter, be sure
to have the appropriate cables to connect
devices.
2 Set SCSI device termination. Devices at both
ends of the SCSI bus must be terminated.
Devices in the middle of the bus, including the
ATTO ExpressPCI adapter, must have
termination removed or disabled. ATTO
ExpressPCI SCSI adapters select the proper
termination if left in auto termination mode.
3 Set SCSI IDs. Each device on the SCSI bus
requires a unique SCSI ID, one different from
the host adapter ID. The default setting for the
ATTO ExpressPCI adapter is 7.
If you need to change this setting, refer to the
ExpressPCI Utilities Installation and Operation
manual. Also refer to your SCSI device
documentation to determine the current SCSI
ID and how to change it. Wide (16-bit) SCSI
devices can be assigned IDs 0 to 7 and 8 to 15,
while Narrow (8-bit) devices can only be
assigned IDs ranging from 0 to 7.
4 Review system documentation to select an
appropriate slot to install your adapter. The
combined power consumption of the expansion
slots must not exceed the limits for your
system. If you have more than one expansion
card installed, ensure power consumption is
within the limits outlined for your system.
5 Power down the computer and unplug the
computer from all power sources.
6 Open the case.
7Install the adapter in any open PCI expansion
slot. Consult your computer’s documentation if
you have questions about how to install an
expansion card in your system.
8 Connect SCSI devices by inserting a SCSI
cable to the connector on the ATTO
ExpressPCI host adapter until you hear a click.
Refer to Chapter 3.1 when selecting cables.
9 Close the computer case and power it up.
ATTO ExpressPCI host adapters come
preconfigured to operate properly in a variety of
common system setups. However, some systems
may benefit by tuning the adapter for optimal
performance. Refer to the
ATTO ExpressPCI
Utilities Installation and Operation
manual for
more information on changing host adapter
settings
.

6
Hardware installation

7
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
3.1 Cabling and termination
Cables and devices must be chosen to maximize performance and minimize the electrical noise from the
high-speed data transfers available with the SCSI protocol. Cabling and termination methods become
important considerations.
Exhibit 3.1-1 The following table lists the maximum number of devices you may connect at specific cable distances
using differential and single-ended SCSI in various SCSI environments.
Setting up cables and termination
Use high quality Ultra 320-rated, well-insulated
SCSI cables to ensure error free communications.
Exhibit 3.1-2 Several internal and external cable
connectors.
The ExpressPCI Ultra320 SCSI host adapter
supports two types of SCSI signaling: Low
Voltage Differential (LVD) and Single-Ended.
Devices on the same SCSI bus must use the same
signaling, either LVD or Single-Ended.
To set up cabling and termination:
1 Determine whether you are using a single
channel or dual channel host adapter model.
One external connector indicates a single
channel host adapter; two external connectors
indicate a dual channel host adapter.
2 Determine if SCSI devices are going to be
installed internally or externally.
• Total bus cable length varies by host adapter
and type of attached devices. Refer to
Exhibit 3.1-1 for details on maximum cable
length.
• If you combine Wide 16-bit and Narrow 8-
bit devices on the same connector, connect
the Wide devices first (closest to the
connector).
• Refer to the documentation for your SCSI
devices to determine if they are Wide or
Narrow, UltraWIDE SCSI, Ultra2 SCSI,
Ultra160 or Ultra 320.
3 Determine which terminator to use
Bus speed
MB/sec. max.
Bus width
bits
Max. bus lengths, meters Max. device
support
Single-ended LVD HVD
SCSI-1 586 - 25 8
Fast SCSI 10 8 3 - 25 8
Fast Wide SCSI 20 16 3 - 25 16
Wide Ultra/WIDE SCSI 40 16 - - 25 16
Wide Ultra/WIDE SCSI 40 16 1.5 - - 8
Wide Ultra/WIDE SCSI 40 16 3 - - 4
Ultra2 SCSI 80 16 - 12 - 16
Ultra160 SCSI 160 16 - 12 - 16
Ultra320 SCSI 320 16 - 12 - 16

8
Cabling and termination
• Use an LVD terminator if you are only using LVD
devices.
Although you can use a Single-Ended
terminator, all devices will be limited to Ultra
SCSI speeds. Single-Ended devices require
a Single-Ended terminator.
If you use an LVD terminator with Single-
Ended devices, the system may hang or
devices may not be seen on the SCSI bus.
Some termination manufacturers provide
automatically sensing terminators.
• External terminators should be attached to the
last external device in the SCSI chain.
Don’t use any other termination on the
external SCSI chain.
The last device on an internal SCSI chain
should also be terminated in one of several
ways.
Many Single-Ended Ultra SCSI and earlier
devices provide a jumper setting for applying
termination: place a jumper over the pins
designated for termination on the last device
on the internal cable. Check with your drive
manufacturer if you are not sure which pins
to use.
• LVD Ultra2 and Ultra160 SCSI devices cannot
supply their own termination.
Use an internal ribbon cable which has a
SCSI terminator attached to the end of it,
connect the unterminated end of the cable to
the host adapter card and the internal drives
to the subsequent connectors.
The terminator should be at the opposite end
of the cable from the host adapter card.
• Wide (16-bit) and Narrow (8-bit) devices can be
connected together on the same connector of
the host adapter card, but wide devices must be
attached first, followed by narrow devices.
To terminate the SCSI bus, the cable or
adapter used to convert from a wide (68-pin)
connector to a narrow (50-pin) connector
provides partial termination, allowing upper
8-bits (or byte) of the wide SCSI bus to be
properly terminated.
A narrow terminator should be used on the
last narrow device to terminate the rest of the
SCSI bus.
A SCSI bus without partial termination
between the wide and narrow devices may at
first appear to work correctly, but occasional
I/O errors occur without proper termination.
• If you use both internal and external connectors
and mix Single-Ended and LVD devices on the
same bus, even if using different connectors, the
host adapter card will operate with Single-Ended
signaling at UltraSCSI speeds.
• Automatic termination
When both internal and external connectors
are used, the host adapter card detects the
presence of devices and turns off
termination.
If devices are removed from one connector
of the card, the host adapter automatically
detects the change, and enables its own
termination.
• Software controlled termination
You may have to override the host adapter’s
automatic termination if only narrow devices
are attached to one connector and wide
devices are attached to the other connector
on the same bus.
The host adapter must supply partial
termination to the upper 8-bits (byte), but not
automatically.
Please refer to your ExpressPCI Utilities
manual for instructions on setting the host
adapter’s termination to Upper Byte.
• Termination power
Host adapters supply termination power to
the bus at all times and many SCSI devices
are also able to supply termination power.
SCSI signal quality, particularly with long or
marginal quality cables, may be improved if
the device supplies the termination power.
Contact your device manufacturer for more
information on your device’s ability to supply
termination power.

9
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
4 Installing drivers
After installing the ATTO ExpressPCI host adapter, you must configure your system to recognize and
use it by installing drivers for your operating system.
Note
If you already have one or more ExpressPCI
adapters installed and you are installing
additional adapter(s), you do not need to
perform any of these procedures unless you
are updating a previously installed driver.
After installing the ATTO ExpressPCI host
adapter, you must configure your system to
recognize and use it by
• installing drivers for your operating system
• updating the adapter firmware if necessary
ATTO ExpressPCI adapters ship with the latest
firmware installed. If you are performing a new
adapter installation, you do not need to update the
firmware. If you are upgrading a previously
installed driver, update the adapter firmware to
ensure proper operation.
1 Go to the Support Downloads menu item in
the ATTO Technology website,
www.attotech.com
2 In the ExpressPCI Host Adapters menu item,
find your ExpressPCI adapter and click on
Download.
3 Find your operating system menu item
• Mac OS X ExpressPCI Drivers
• Windows ExpressPCI Drivers
• Linux Support for ExpressPCI patches for
the LSI Logic Fusion-MPT driver in the
Linux 2.4 and 2.6 kernels
• Novell Netware ExpressPCI drivers
4 Download the appropriate driver.
5 For the Novell Netware ExpressPCI Drivers
menu, select the readme.txt file
For all other drivers, release notes and
installation instructions are included in the
download packages.
6 Follow the installation instructions.
7 Update the adapter firmware using the ATTO
Configuration Tool or the ExpressPCI BIOS
Setup Utility. Refer to Use the ATTO
Configuration Tool and Use the ExpressPCI
BIOS Setup Utility on page 10.

10
Updating hardware flash
5 Updating hardware flash
ATTO ExpressPCI adapters ship with the latest firmware installed. If you are performing a new adapter
installation, you do not need to update the firmware. If you are upgrading a previously installed driver,
update the adapter firmware to ensure proper operation.
Visit the ATTO Technology website,
www.attotech.com , for the latest drivers and
firmware.
Use the ATTO Configuration Tool
1 Download the most recent version of the
Configuration Tool from the ATTO web site,
www.attotech.com.
Refer to the ATTO Utilities Installation and
Operation Manual for additional information on
downloading and using the Configuration Tool.
2 Download the flash bundle for your adapter
from the ATTO web site and extract them to
your desktop.
3 Install the Configuration Tool on your system.
4 Launch the Configuration Tool.
5 In the Device window, select your adapter
6 In the Flash window, click on the Browse
button to find the flash bundle that you
previously downloaded to your desktop.
7 Click Update to update your flash ROM.
8 Reboot your system for the flash changes to
take effect.
Use the ExpressPCI BIOS Setup Utility
Note
BIOS utilities are not available on Itanium
systems. Use the ATTO Configuration Tool
to update flash on Itanium systems.
1 Download the latest Windows driver package
from the ATTO Technology website.
2Runmakedisk.bat in the Windows driver
package and follow the instructions for creating
the driver floppy disk.
3 Reboot the PC.
4 During the reboot, an ATTO Technology
banner displays that the host adapter is
detected.
5 Enter Control-Z when prompted to begin the
setup utility within a few seconds after the
banner appears.
If you do not enter Control-Z soon enough after
the banner appears, repeat steps 3-5.
6 In the utility, select the Adapter Menu.
7SelecttheUpgrade Flash ROM option.
8 Insert the driver disk from step 1 into the floppy
drive.
9 Follow the on-screen instructions.
10 Remove the disk and reboot your system for
the flash ROM changes to take effect.

i
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
Appendix A Standards and compliances
The equipment described in this manual generates and uses radio frequency energy. The Technical
Specification sheet for a particular ATTO ExpressPCI host bus adapter list certifications for that model.
FCC standards: radio and television interference
WARNING
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Canadian standards
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European standards
Declaration of Conformity
This following statement applies to the ATTO ExpressPCI host bus adapter.
This device has been tested in the basic operating configuration and found to be compliant with the
following European Union standards:
Application of Council Directive: 89/336/EEC
Standard(s) to which conformity is declared: EN55024:1998
This Declaration will only be valid when this product is used in conjunction with other CE approved
devices and when the entire system is tested to the applicable CE standards and found to be compliant.
The EPCI-UL4D-0R0, EPCI-UL4S-0R0, EPCI-UL5D-0R0 and EPCI-UL5D-
L00 comply with Directive 2002/95/EC on the Restriction of the Use of
Hazardous Substances in Electrical and Electronic Equipment (RoHS).

ii
Appendix B ATTO product guide
Contact an ATTO Technology authorized sales representative to order.
SCSI adapter selection guide
Product Features
Ultra 320 SCSI
UL5D UL5D LP UL4D UL4S
Max. transfer rate (MB/sec.) 640 640 640 320
Low Voltage Differential • • • •
Single-ended SCSI • • • •
Number of SCSI Channels 2/2 0/2 2/2 1/1
Number of SCSI IDs supported 30 30 30 30
Low profile •
Large file transfers • • • •
Cable distances (m) 12.5 12.5 12.5 12.5
32-bit PCI compatible • •
64-bit PCI compatible • •
33 MHZ PCI • •
133 MHZ PCI-X • •
66 MHz PCI • •
x4 PCI Express • •
Windows 2000/XP, Server 2003 support • • • •
Linux support • • • •
Mac OS X support • • • •
Novell Netware support • • • •
RoHS compliant • • • •

iii
ATTO Technology Inc. ExpressPCI Host Adapter Installation and Operation Manual
Celerity FC storage adapter selection guide
Product Features Celerity
FC-44ES
Celerity
FC-42ES
Celerity
FC-41ES
Celerity
FC-42XS
Celerity
FC-41XS
Celerity
FC-21PS
Fibre Channel Ports 4 2 1 2 1 1
FC protocol 4-Gb 4-Gb 4-Gb 4-Gb 4-Gb 2-Gb
Maximum Transfer Rate (half
duplex)
1.6 GB/sec 800
MB/sec
400
MB/sec
800
MB/sec
400
MB/sec
200
MB/sec
Maximum Transfer Rate (full
duplex)
2 GB/sec 1 GB/sec 800 MB/sec 1 GB/sec1800
MB/sec
1 GB/sec
Bus Type PCIe PCIe PCIe PCI-X PCI-X PCI-X
Bus Characteristics38 lane 4 lane 4 lane 64-bit
133 MHz2
64-bit
133 MHz2
64-bit
133 MHz2
Optical Interface SFP LC SFP LC SFP LC SFP LC SFP LC SFP LC
Maximum Cable Length 300m@2-Gb
150m@4-Gb
300m@2-Gb
150m@4-Gb
300m@2-Gb
150m@4-Gb
300m@2-Gb
150m@4-Gb
300m@2-Gb
150m@4-Gb
500m@1-Gb
300m@2-Gb
Low Profile form factor • • • •
Advanced Data Streaming
(ADS™) Technology
• • • • • •
Software RAID support3• • • • • •
Developer's Kit (Target Mode &
API)
• • • • • •
Windows support • • • • • •
Linux (Red Hat, SUSE) driver • • • • • •
Macintosh OS X driver • • • • • •
Novell Netware support • • • • •
Solaris support • • • • •
Free BSD • • • • •
RoHS compliant • • • • •
1 Performance ceiling is constrained by 133 MHz PCI-X bus transfer speed
2 Backward compatible to 32-bit and 33 MHz PCI; FC-21PS is 3.3V/5V Universal
3 ATTO ExpressStripe for OS X available; Express Power Center and other software RAID supported for Windows

iv
Appendix C Contact ATTO Technology, Inc.
Customer service, sales information and technical support are available by phone Monday through Friday,
Eastern Standard Time 8:00 a.m. to 8:00 p.m., or by e-mail and web site 24-hours a day.
ATTO Technology, Inc.
155 CrossPoint Parkway
Amherst, New York 14068
[phone] • voice
[phone] • fax
http://www.attotech.com
ATTO Technology can also be reached via e-mail at the following addresses:
Sales Support:[email protected]
Technical Support:[email protected]