Attop W70 User manual

W70 Instructions For Use
(Please keep and read this manual carefully before using this product.)
4
Customer Service Email: [e-mail]
www.attoptoys.com
Get 24/7 assistance at
Use camera or QR scanner to scan
Or Visit: https://attop.afterservice.vip

-01-
1. Please read this Disclaimer & Warning and Safety Guidelines carefully
before using our product. This product is not recommended for people
under the age of 14. By using this product, you hereby agree to this
disclaimer and signify that you have read it fully. You agree that you are
responsible for your own conduct and any damage caused while using this
product, and its consequences. You agree to use this product only for
purposes that are proper and in accordance with local regulations, terms
and all applicable policies and guidelines ATTOP may make available.
2. When using this product, please be sure to strictly abide by the specica-
tion requirements and safety guidelines stated in this document. Any
personal injury property damage, legal disputes and all other adverse
events caused by the violation of the safety instructions or due to any other
factor, WILL NOT be ATTOP’s responsibility.
DISCLAIMER & WARNING
SAFETY GUIDELINES
Check Before Using:
① This product is a high precision drone that integrates various electronic
stability and control mechanisms. Please be sure to set up this drone
carefully and correctly to ensure safe and accident-free operation.
② Please be sure that the batteries of the drone and controller are clean,
undamaged and fully charged.
③ Please be sure that all the propellers are undamaged and installed in the
correct orientation.
④Please do a thorough check of the product before using. Inspect the
integrity of the parts, any signs of cracks and wear of the propeller, battery
power and eectiveness of the indicator, etc. After doing a complete check,
if any issue is found, please stop using the product until the issue has been
solved.

-02-
Flight Environment:
Fly in Open Areas Maintain Line
of Sight
Fly Below
390 feet (120 m)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
① Avoid ying over or near obstacles, crowds, high voltage power lines,
trees, South Pole, North Pole and base station.
② DO NOT y near strong electromagnetic sources such as power lines and
base stations as it may aect the onboard compass.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
③ Don’t use this drone in adverse weather conditions such as rain, snow,
fog, and wind.

-03-
Operation Requirements：
①Please don’t use this product to follow any moving vehicles.
②During the ight, only turn o the motor in case of an emergency.
③As battery becomes low, return the drone back to your starting point.
④This product should not be used while drinking alcohol, if you are
feeling fatigued, taking medicine, or feeling any physical discomfort.
⑤Beware of the noise volume the drone produces. Keep your distance to
avoid ear damage.
Use of Battery:
Use of Gimbal:
①Do not charge the battery at low temperature (lower than 50°F).
②Do not operate the drone at low temperature (lower than 50°F).
③Please ensure batteries are tted in the correct orientation as shown in
the instruction manual.
④Avoid short circuits by tting the batteries incorrectly, and do not crush
or squeeze the batteries as this could carry the risk of an explosion.
⑤Do not mix new and old batteries as this can lead to a poor performance
of the product.
①The Gimbal is detecting about 10 seconds after compass calibration.
When the Gimbal indicator light is solid on, it indicates that the detection
completes.
②Do not touch the Gimbal.
③If the Gimbal gets stuck 5 times or more, it will be out of running and the
Gimbal indicator light will be solid on. Please reboot the drone.
⑥Stay away from the
rotating propellers and
motors.
⑦Don’t y in the
No-Fly Zone.
⑧Don’t touch the
Gimbal.

-04-
⑥Dispose of used batteries carefully. Do not litter.
⑦Please keep dead batteries away from heat and re.
⑧If the device is not going to be used for an extended period of time,
remove batteries to prevent potential damage from battery leakage.
⑨It is recommended to only use the USB charging cable that comes with
the drone to charge the battery.
⑩Don't connect the battery directly to wall outlets or carcigarette lighter
sockets.
Don't attempt to disassemble or modify the battery in any way.
Don't use the battery if it gives o an odor, generates heat, becomes
discolored or deformed, or appears abnormal in any way. If the battery is in
use or being charged, remove it from the device or charger immediately
and discontinue use.
Don't pierce the battery casing with a nail or other sharp object, break it
with a hammer, or step on it!
Always charge the batteries in a reproof container and away from
combustible materials. Don't charge the batteries on surfaces that can
catch re. This includes: wood, cloth, carpet, or in the application's device.
Don't immerse the battery in water or allow it to get wet.
Don’t solder battery terminal directly.
Keep the battery out of the reach of children or pets.
Don't short-circuit the battery by connecting wires or other metal
objects to the positive(+) and negative(-) terminals.
11
12
13
14
15
16
17
18
Li-Po Battery Disposal & Recycling
Lithium-polymer batteries must not be placed with household trash.
Please contact local environmental or waste agency or the supplier
of your model or your nearest Li-Po battery recycling center.

-05-
×1 ×1 ×2
×8 ×1 ×1
MAINTENANCE
①Clean the product after using with a clean and soft cloth.
②Avoid prolonged exposure to direct sunlight and avoid buildup of heat
on the drone.
③ This device is not waterproof and must not be submerged in water
under any circumstance. Failure to maintain the device completely dry will
result in the failure of the unit.
④Check the charging plug and other accessories for signs of damage
frequently. If any part of the device is damaged, refrain from ying until
maintenance can be carried out.
Drone Controller Drone Battery
Propeller USB Charging
Cable Screwdriver
PACKAGE CONTENTS

-06-
DRONE’S DETAILS
TOP
BOTTOM
Lights
Vision Positioning Lens
Battery
Propeller B
Propeller B
Propeller A
Propeller A
HD Camera
Power Switch

-07-
TOP
BACK
FRONT
CONTROLLER DETAILS
Controller Functions
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Gyroscope calibration
Return to Home
Right Joystick
Left Joystick
Unlock
Speed
Antenna
Phone Holder
Camera Angle
Adjustment
Follow me Switch
Record Video
Take Photos
Charge
+
-
CHA

+
-
+
-
-08-
•Return to Home
Press the button to start the RTH. The controller emits a “beep-beep”
sound every 1.5 seconds as the drone ies back to the recorded Home
Point.
Press the RTH button again to exit RTH procedure and regain control of
the drone.
•Photo/Video
•Speed Switch
Press the button “ ” on the Controller and you will hear a “beep”,
indicating the drone is at low speed.
Press the button “ ” again and you will hear two beeps, indicating the
drone is at high speed.
•Follow me Switch
•Unlock/Lock
Press the button and the camera icon “ ” on the Controller, the
camera takes one photo.
Press the same button, the video icon “ ” on the Controller, the
camera will take the video. Press again will exit shooting.
When the Follow Me function is enabled, the drone will follow the GPS
in your smart phone to follow you wherever you go.
Low speed is the default setting.
Press the button ” “ then the motor will rotate.
Pull the Left Joystick to the bottom position. The motor will stop rotating
and the drone will be locked.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
-10-
INSTALLATION
Installation: Push the battery into the battery compartment of the drone.
Make sure it “clicks”into place indicating the battery is rmly installed.
Attention:
The battery should be installed rmly. Failure to do so may aect the ight
safety of your drone. The drone may crash due to a power-cut during ight.
Removal: As shown above, press and hold the locks on both sides of the
battery at the same time to remove the battery.
Drone Battery

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
-11-
Install TF Card
Controller Battery
Tips: Please turn o the controller before charging.
5V
TF
1. Connect the USB cable to a USB socket such as a mobile power supply.
2. Connect the controller with the USB cable. Solid green LEDs indicate
charging status. Charging is completed when LEDs are no longer on.
Low battery warning
When the controller indicator light ashing and controller handle emits a
"beep" alarm sound every 3 seconds, indicating that the controller power is
too low. The controller needs to be charged at this time.
Notes:
1. Charge only by USB cable of factory provided.
2. Use a power supply with standard output voltage 5V and current greater
than or equal to 2A, otherwise there is a risk of overloading the USB cable
and battery. A full charge takes approximately 90 mintutes.
Tips: Please turn o the controller before charging.
As shown in the above gure, please insert the TF card (needs to be
purchased separately) into the TF card slot. A “click” signies it is inserted
correctly. It will indicate memory card capacity in “SD Card testing ” of
APP interface, which means the card was indentied.
1. Click the SD card testing will delete all contents in the SD card and
connot be recovered. Please be careful before conrmation.
2. The original pixel-sized pictures and videos will be stored on the TF card.
SD

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
AB
B A
-12-
Propellers
The drone will not y unless the correct propeller is installed on the correct
motor shaft. See illustration above. An “A” or “B” is printed on the back of
each propeller. Lock the propeller to the motor shafts with screws rotating
each screw clockwise.
Installation
HEAD
Removal
For propeller removal, use screwdriver (provided) to rotate counter-clock-
wise and remove propellers.

-13-
Phone Holder
①Separate the Mobile Device Holder by pulling out from of
controller.
②Adjust the Mobile Device Holder for a tight grasp of your phone.
2 1
1
2

2
1
-14-
CHARGING
①Connect the USB cable to a USB socket such as a mobile power supply
(Use a power supply with standard output of 5V and current equal to but
no greater than 2A). Connect battery with the USB cable. The battery's LEDs
begin ashing. When all four LEDs become solid, full charging is completed.
②The charging time of a single battery is 4~6 hours.
. Charge only by USB cable of factory provided.
· Before charging, please carefully review the “ Use of Battery” section
contained in “ SAFETY GUIDELINES”.
· This product is only equipped with a single battery, you can choose to buy
another battery to experience a longer ight.
· Use an power supply with standard output voltage 5V and current greater
than or equal to 2A, otherwise there is a risk of overloading the USB cable
and Battery.
USB Adapter
(5V/2.0A)

-15-
Download APP
OPERATION GUIDE
HEAD
To unfold the drone follow the steps below.
Step 1: Unfold the front arms.
Step 2: Unfold the rear arms and place drone on a at, level surface. Head
should face forward.
Unfolding the Drone
Scan the QR code, corresponding to either App Store™ or Google™ Play
Store and download the“ Attop View ” application for free.
Required Operating Systems: iOS v8.0 and later / Android v4.3 and later
Tip: Please use a smartphone that can support receiving 2.4G and 5G WiFi
signals.
CONTACT US
Please do not hesitate to contact us if you need further support.
Customer Service Email:
[email protected]

-16-
+
-
Connecting to Wi-Fi
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
① Connect your smart phone to the Wi-Fi network created by the drone.
Check the drone’s status in the ”Attop View” app.
②Your smartphone will launch a search of the available Wi-Fi networks:
③Select the Wi-Fi network: W70-XXXXXX
④Wait for several seconds until your smartphone connects to the drone's Wi -Fi
network.
⑤Launch the Attop View application.
> The connection between your smartphone and the drone will be
established automatically.
This connection is generally represented by the Wi-Fi logo appearing on
your smartphone’s screen.
W70-XXXXXX
①First, press the drone Power Switch and quickly release. Then, press again
and hold for approximately 2 seconds. The drone will emit a sound and the
battery LEDs will brightly illuminate indicating it is now powered up. Place the
drone on a at, level surface with the head facing forward.
②Turn on the switch on the controller by sliding it to the top. Once the
controller emits "beep-beep" sound, it conrms that the drone and controller
are now successfully paired.
Pairing

-17-
After successful pairing, the drone’s LED lights ash rapidly. You can now
begin compass calibration.
Step 1:
Now, the APP interface displays the above diagram. Hold the drone
horizontally and rotate the drone in approximately 3 complete circles.
When completed, the controller emits a “beep” sound and the drone's
LED lights ash slowly.
Front lights
Rear lights
ash rapidly ash slowly
Calibrating the Compass
●Push Left Stick to top right corner and Right Stick to top left corner
simultaneously to activate Compass calibration (Pic), when operating the
drone and app at rst time.
●Compass calibration will be activated automatically after rebooting 30
times.
●Retrun the drone when the app warns ”Geomagnetic anomaly, please
leave the source of interference and recalibrate the compass!”.
Please move to open space without interference to operate the drone.
Push left stick to top right corner, right stick to top left corner simultane-
ously for activate compass calibration.
Attentions:
+
-

3 S
-18-
HEAD
Horizontal Calibration
Step 2:
Now, the APP interface displays the diagram. Hold the drone vertically and
rotate the drone in 3 complete circles. When completed, the controller
emits a “beep” sound and the drone's LED lights become solid.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Slide right to confirm
Front lights
Rear lights
Now, the APP interface displays the diagram. Place the drone on a at level
surface and . The LED lights of the drone will ash rapidly
for about 3 seconds. When completed, the front and rear lights turn solid. Or
press the Gyroscope calibration switch“ ”on the controller. The LED lights
of the drone will ash rapidly for about 3 seconds. When completed, the
front and rear lights turn solid.
ash slowly Solid
ash rapidly Solid
Attentions:
●Now the Gimbal is detecting for roughly 10 seconds. Please do not
touch the Gimbal.
●Horizontal calibration is carried out after compass calibtation.
●Searching GPS signal after horizontal calibration completed, indicates
“ GPS signal searching.....”in the app interface, please wait patiently.
●When it indicates “Equipment connected (GPS Mode)” and “Ready to
Fly” in the app interface, it means that the drone receives the GPS signal.
Now, the rear LED's of the drone will ash twice per second.

+
-
+
-
-19-
Unlocking the Motor
Locking the Motor
Pull the Left Joystick to the lower position. The motor will stop rotating and
the drone will be locked. (Pic.1)
Pic. 1
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Please unlock the motor before take-o.
Press the button “ ” , the motors rotate.
①Unlocking the motor
Please unlock the motor while it indicates
“Equipment connected (GPS Mode)”
and “Ready to Fly” in the app interface.
②If you do not perform any operation approximately 10 seconds after unlocking
the drone, the motors will stop rotating.

①②
90°
-20-
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
One Key Take-o/Landing
① After unlocking the drone, press the “ ” button in the APP interface,
then “ ” and the drone will automatically taking o
and hover at 1.5m altitude. Or press the button “ ” again for taking o
after unlocking the motors.
②When drone is ying, press the “ ” button, the drone will y back
to the Home Point and automatically land on the ground.
Landing
Take-o
Tips:
Before ying, make sure the GPS Mode is turned on in case the drone gets
lost!
Camera Angle Adjustment
FUNCTION DETAILS
During ight, you can dial the wheel left/right to tilt the camera
up/down. (The gimbal has a 90° tilt range.)
Slide right to confirm
Please do not touch the camera gimbal directly. Doing so may cause damage!