Aube Technologies TH209 User manual

TH209
Non-programmable Thermostat
Owner’s
Guide
69-2771EF-07

Do you need assistance?
We are here to help.
For assistance with this product please call
Customer Care toll-free at
1-800-468-1502.

TH209
Table of Contents
About your new thermostat ......................................................1
Temperature display and setting............................................2
Removing the faceplate .............................................................3
Wiring ................................................................................................4
Installing the faceplate...............................................................5
Selecting the temperature display format..........................6
In case of difficulty.......................................................................7
Specifications.................................................................................8
3-year limited warranty ..............................................................9

OWNER’S GUIDE
1
About Your New Thermostat
This thermostat can be used to control an electric heating system
such as a baseboard heater or a convector.
The thermostat CANNOT be used with:
• a resistive load under 0.83 A
• a resistive load over 8.3 A
• a system driven by a contactor or a relay (inductive load)
• a fan-forced heating system (e.g. : fan-forced convector)
• a central heating system
SUPPLIED PARTS
• One (1) thermostat
• Two (2) 6-32 mounting screws
• Two (2) solderless connectors

TH209
2
Temperature Display and Setting
The thermostat normally displays the actual (ambient) temperature.
• To view the setpoint temperature, briefly press the Up or Down button. The setpoint
will be displayed for 5 seconds.
• To change the setpoint temperature, press the Up or Down button until the desired
value is displayed.
Temperature
display
Heating intensity
indicator
(No image appears
when heating is
off.)
Up button
Down
button
Appears when the
setpoint is
displayed

OWNER’S GUIDE
3
Removing the
Faceplate
TURN OFF POWER OF THE
HEATING SYSTEM AT THE
MAIN POWER PANEL TO
AVOID ELECTRIC SHOCK.
Loosen the screw holding
the faceplate to the base.
The screw cannot be
completely removed and
remains captive on the
base. Remove the faceplate
from the base by pulling the
bottom half.

TH209
4
Wiring
Connect either one of
the thermostat wires
to the heater wire and
the other one to the
power supply wire
using solderless
connectors for copper
wires.
NOTE: All cables and
connections
must conform
to the local
electrical code. Special CO/ALR solderless connectors must be
used when connecting with aluminum conductors.
2-wire installation 4-wire installation
Power supply
Power supply

OWNER’S GUIDE
5
Installing the
Faceplate
Install the base onto
an electrical box.
Reinstall the faceplate
on the base and
secure it in place with
the screw.
NOTE: Keep the air vents of thermostat clean and unobstructed at
all times.

TH209
6
Selecting the Temperature Display Format
To select the temperature display format:
1. Press the Up and Down buttons for three seconds. The
format currently used will be indicated on the screen.
2. Press the Up or Down button to change the format.
3. P
ress the Up and Down buttons for one second (or wait
for one minute) to return to the normal display
.

OWNER’S GUIDE
7
Table 1. In Case of Difficulty
Problem Solutions
Thermostat is hot. This is normal.
Displayed
temperature is wrong. Remediate if any the following conditions exists: The thermostat is exposed to air draft.
The sticker on the thermostat’s screen has not been removed.
The thermostat is located near or above a heat source such as a
light dimmer.
Display disappears
and reappears after a
few minutes.
The thermal protection device on the heater has temporarily
opened. This can happen if the heater is obstructed by furniture
or curtain and has overheated, or if the heater’s thermal
protection device is too sensitive.

TH209
8
Specifications
Supply: 120/208/240 VAC, 50/60 Hz
Minimum load:
0.83 A (resistive only)
200 W @ 240 VAC
100 W @ 120 VAC
Maximum load:
8.3 A (resistive only)
2000 W @ 240 VAC
1000 W @ 120 VAC
Display range: 0°C to 50°C (32°F to 99°F)
Setpoint range: 5°C to 30°C (40°F to 85°F)
Storage: -20°C to 50°C (-4°F to 120°F)
Permanent memory:
You do not need to adjust the temperature following a power
outage.
ICES-3 Class B Notice: This Class B digital apparatus complies with
Canadian ICES-3.
Energy Verified
Only

OWNER’S GUIDE
9
3-Year Limited Warranty
Resideo warrants this product to be free from defects in workmanship or materials,
under normal use and service, for a period of three (3) years from the date of first
purchase by the original purchaser. If at any time during the warranty period the product
is determined to be defective due to workmanship or materials, Resideo shall repair or
replace it (at Resideo’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which
you purchased it; or
(ii) call Resideo Customer Care at 1-800-468-1502. Customer Care will make the
determination whether the product should be returned to the following address: Resideo
Return Goods, Dock 4 MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, or
whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by Resideo that the defect was caused by damage which occurred
while the product was in the possession of a consumer.

TH209
10
Resideo’s sole responsibility shall be to repair or replace the product within the terms
stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY
KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR
IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so this limitation may
not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS WARRANTY. Some states
do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary
from state to state. If you have any questions concerning this warranty, please write
Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422
or call 1-800-468-1502.

OWNER’S GUIDE
© 2020 Resideo Technologies, Inc. All rights reserved.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Tous droits réservés. Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.
www.resideo.com
Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
69-2771EF—07 M.S. Rev. 01-21 | Printed in United States
CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the
nearest authorized collection centers or authorized recyclers. The correct disposal of
end-of-life equipment will help prevent negative consequences for the environment and
human health.

TH209
Thermostat non programmable
Guide de
l’utilisateur
69-2771EF-07

Besoin d'aide?
Nous sommes là pour vous aider.
Pour obtenir de l’aide sur ce produit, joindre le service à
la clientèle en composant sans frais le 1-800-468-1502.

TH209
Table des matières
À propos du thermostat..............................................................1
Affichage et réglage de la température ...............................2
Enlever la façade...........................................................................3
Branchement..................................................................................4
Installer la façade .........................................................................5
Selectionner le format d’affichage de la température...6
En cas de difficulté.......................................................................7
Fiche technique.............................................................................8
Garantie limitée de 3 ans...........................................................9

GUIDE DE L’UTILISATEUR
1
À propos du thermostat
Ce thermostat a été conçu pour commander un appareil de
chauffage électrique tel qu’une plinthe chauffante ou un convecteur.
Ce thermostat NE PEUT être utilisé avec :
• une charge résistive inférieure à 0,83 A
• une charge résistive supérieure à 8,3 A
• un appareil muni d’un contacteur ou d’un relais (charge inductive)
• un appareil muni d’un ventilateur (exemple : ventiloconvecteur)
• un système de chauffage central
PIÈCES FOURNIES
• Un (1) thermostat
• Deux (2) vis de montage 6-32
• Deux (2) connecteurs sans soudure

TH209
2
Affichage et réglage de la température
Le thermostat affiche normalement la température mesurée (ambiante).
• Pour afficher la température de consigne, appuyer brièvement sur le bouton Haut
ou Bas. La température de consigne sera affichée pendant 5 secondes.
• Pour modifier la température, appuyer sur le bouton Haut ou Bas jusqu’à ce que la
valeur désirée apparaisse.
Indicateur de l’intensité
du chauffage. (L’absence
de l’image indique l’arrêt
du chauffage.)
Affichage de la
température Bouton
Haut
Bouton
Bas
Apparaît lorsque la
température de
consigne est affichée

GUIDE DE L’UTILISATEUR
3
Enlever la façade
METTRE LE SYSTÈME DE
CHAUFFAGE HORS TEN-
SION AFIN D’ÉVITER
TOUT RISQUE DE CHOC
ÉLECTRIQUE.
Desserrer la vis qui retient
la façade du thermostat à
la base. La vis ne peut être
complètement enlevée et
reste captive sur la base.
Séparer la façade de la
base en tirant sur la partie
inférieure du thermostat.