Aube Technologies TH131 User manual

TH131 & TH133 400-131-002-C 1/11/06 1/2
NOTE: Even if the following illustrations show the TH131 model only,
they can also apply to the TH133 model.
This user guide covers the following thermostat models:
• TH131 A/F/AF
• TH133 A/F/AF
The TH131 model is designed for residential applications, whereas
the TH133 model is designed for public areas as its controls are hid-
den and thus protected against unauthorized access. Both models
can be configured for the following applications:
NOTE: Keep the thermostat's air vents clean and free from obstruc-
tions.
3.1 Application Types
Position the switch, on the back of the control module, according to
your application.
3.2 Minimum and Maximum Limits (TH131 only)
Use the two potentiometers on the
back of the control module to set
the minimum and maximum tem-
perature limits. Depending on your
application, the potentiometers
limit the following temperature:
ambient temperature (A)
floor temperature (F or AF)
Use a flat-tip screwdriver to rotate
the potentiometers until the notch
points to the desired temperature
limit.
nDescription
1.
Type Application
A Controls the ambient (room) temperature
F Controls the floor temperature
AF Controls the ambient temperature and limits the floor temperature
Heating indicator
Temperature
selection dial
On/Off switch
Pilot wire indicator
(Europe only)
TH131
TH133
Front View Rear View
oInstallation
2.
pConfiguration
3.
Type Switch Position
AUP(A/AF)
AF UP (A/AF)
FDOWN(F)
Control Module
Power Base
notches
TH131 & TH133
User Guide
Electronic Thermostat

TH131 & TH133 400-131-002-C 1/11/06 2/2
4.1 Temperature Adjustment
TH131
Use the dial on the front of the thermostat to set the desired tempera-
ture.
NOTE: If the dial is placed at a temperature beyond the high or low
temperature limit, the temperature will be maintained at that limit (see
section 3.2).
TH133
Remove the control module from the base and use the dial on the
back of the control module to set the desired temperature.
4.2 On/Off Switch (TH131 only)
Use the On/Off switch to turn the thermostat Off when it is not used
(e.g., in the summer).
TH131 accepts the six following pilot wire orders when installed on a
230 V power base.
Setpoint range: 7°C, 15°C to 35°C (45°F, 59°F to 95°F)
Minimum temperature limit: 5°C to 25°C (41°F to 77°F)
Maximum temperature limit: 15°C to 35°C (59°F to 95°F)
Accuracy: ± 0.2°C (0.36°F)
Storage: -20°C to 50°C (-4°F to 120°F)
Heating cycle length: 15 minutes
Software: Class A
Controller: Electronic
Size (H/W/D):
•TH131: 78.9 x 78.9 x 16.3 mm (3.1 x 3.1 x 0.64 in.)
•TH133: 78.9 x 78.9 x 18 mm (3.1 x 3.1 x 0.71 in.)
AUBE TECHNOLOGIES INC. THREE (3) YEAR LIMITED WARRANTY
Aube warrants this product, excluding battery, to be free from defects
in the workmanship or materials, under normal use and service, for a
period of three (3) years from the date of purchase by the consumer.
If at any time during the warranty period the product is determined to
be defective or malfunctions, Aube shall repair or replace it (at Aube's
option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to
the place from which you purchased it, or
(ii) contact Aube. Aube will make the determination whether the
product should be returned, or whether a replacement product
can be sent to you.
This warranty does not cover removal or reinstallation costs. This
warranty shall not apply if it is shown by Aube that the defect or
malfunction was caused by damage which occurred while the
product was in the possession of a consumer.
Aube's sole responsibility shall be to repair or replace the product
within the terms stated above. AUBE SHALL NOT BE LIABLE FOR
ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE
OF THIS PRODUCT. Some regions do not allow the exclusion or
limitation of incidental or consequential damages, so this limitation
may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE
MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR
DURATION OF THIS WARRANTY. Some regions do not allow
limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other
rights which vary from region to region.
If you have any questions about the product installation or operation,
or concerning the warranty, contact us at:
For more information on our products, go to
www.aubetech.com
qOperation
4.
rPilot Wire Orders (Europe only)
5.
ORDER SIGNAL DESCRIPTION
Comfort No signal Maintain temperature at setpoint
Reduced setpoint
(3.5k setback) Maintain temperature at 3.5°C below setpoint
frost protection Maintain temperature at 7°C
Off Stop heating
1k setback Maintain temperature at 1°C below setpoint
2k setback Maintain temperature at 2°C below setpoint
sSpecifications
6.
;Warranty
7.
Customer Assistance
8.
705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8
Tel.: [phone]
Toll Free: 1-800-831-AUBE
Fax: [phone]
Email: [email protected]m
10 rue Ampère
95500 Gonesse
France
Tel.: [phone]
Fax: [phone]
Email: [email protected]

PB130-024T 400-130-002-C 1/11/06 1/1
This document describes the connections when the PB130-024T
power base is used on any TH13x series thermostat. This
low-voltage power base can be connected to a line-voltage load
using a relay or directly to a 24-volt device. The PB130-024T is
compatible with most relays; however, the following Aube relays are
optimized for use with this power base:
• RT850 solid-state relay (SSR)
• RT850T solid-state relay (SSR) with built-in 24-V transformer
• RC840 electromechanical relay
• RC840T electromechanical relay with built-in 24-V transformer
nOne (1) power base
oTwo (2) plastic anchors
pTwo (2) mounting screws
For a new installation, choose a location about 1.5 m (5 ft.)
above the floor.
The thermostat must be installed on an inside wall facing the
heating system (except for floor heating systems).
Avoid locations where there are air drafts (top of staircase, air
outlet), dead air spots (behind a door), direct sunlight or
concealed chimney or stove pipes (except for floor heating
systems).
The installation must be carried out by an electrician and must
comply to local electrical codes.
nTurn off power to the heating system at the main electrical panel
to avoid electrical shock.
oWire the base according to your application. See typical wiring
diagrams in sections 4.1 to 4.4.
pFor a floor heating system installation, con-
nect the floor sensor between the S and R ter-
minals.
qSecure the base to the wall using the provided screws and wall
anchors.
rConfigure the switches located on the control module (if any).
Refer to the user guide.
sInstall the control module onto the base.
tApply power to the heating system.
uVerify the installation by checking that the heating system can be
turned On or Off using the thermostat.
4.1 Single SSR with Built-in Transformer
4.2 Multiple SSRs with External Transformer
4.3 Electromechanical Relay with External Transformer
4.4 Hot Water Heater Valve
Maximum load: 0.5 A / 24 VAC
Operating temperature: 0°C to 50°C (32°F to 122°F)
Storage: -20°C to 50°C (-4°F to 122°F)
Size(H•W•D): 75 x 75 x 13 mm (2.9 x 2.9 x 0.5 in)
Wire gauge: 14 to 22 AWG
nApplications
1.
oSupplied Parts
2.
pInstallation Guidelines
3.
qInstallation Procedure
4.
rTechnical Specifications
5.
Electrical
Panel
Heater
Blue Red
Black
Electrical
Panel
Heater
Heater
External 24 V
Transformer
Red
Red
Black
Black
Electrical
Panel
Heater
External24V
Transformer
Electrical
Panel
Valve
External24V
Transformer
PB130-024T
Installation Instructions
24-V Low-Voltage Power Base