Audibax Volcano 1500 RGBW User manual

Volcano 1500 RGBW
Please read the manual before using the product
USER´S
MANUAL
7
Volcano 1500
RGBW
9. LED Spe xxx
Adjust the LED speed/strobe/fade of the LED program mode
10. Temper Max:xxx
Adjust the maximum heating temperature of the heating element, adjustable between 285° - 330°C.
11. LED Sync Set Yes/No
Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on.
TIMER CONTROL
Press the Timer key to activate the timer function. The display shows the adjusted interval and the device
counts the seconds down to "0". After that, the fog emission is triggered at the volume adjusted under "Volume
Out". The duration depends on the settings adjusted under "Duration Set". If you wish to deactivate the timer
function, press the Timer key once more.
Manual control (locked)
Press the Lock button for immediate triggering of the fog emission at the volume adjusted under "Man Volume".
Press the lock button more in order to stop the fog emission.
Manual control (100% output)
Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key loose in
order to stop the fog emission.
DMX-512 CONNECTION
DMX Control
Connect the machine directly to a DMX controller or a DMX loop with multiple DMX effects. The machine uses
a 3-pin XLR
connector for DMX connection.
Address Setup:
Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons the
start address may be set. The start address is defined as a first channel to which the machine will respond to.
Check that there are no overlapping channels used!
OPERATION
•Place the unit on a flat, stable surface which must not be tilted more than 10°
•Fill the tank up to the marking with a good quality smoke fluid.
•Switch the unit on via the On/Off switch on the rear side.
•Switch the unit off after use and unplug it from the mains if it will not be used for a long period of time.
•Rinse the unit regularly with clean water.
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse,
unplug mains lead.
Procedure:
If you are using a standard DMX controller, you can connect the DMX-output of the controller
directly to the DMX- input of the first unit in a DMX-chain. Always connect the output of one unit
with the input of the next unit until all units are connected.
If you use a controller with 5 pin DMX connection you will need to use a 5-pin to 3-pin adapter.
At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between
signal (-) and signal (+)
into a 3-pin XLR connector and plug this into the DMX output of the last fixture in the chain.
Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.

USER´S
MANUAL
Volcano 1500 RGBW
1 6
The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate
the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between
5°C/41°F and 35°C/95°F.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the
product. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages
caused by inappropriate use or disrespect of the warnings contained in this manual.
UNPACKING INSTRUCTION
CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure
that all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damage from shipping or the package itself shows
signs of mishandling. Save the package and all packing materials. In the event that the product must be
returned to the factory, it is important that the product be returned in the original factory box and packing.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
POWERSUPPLY
On the label on the backside of the product is indicated on this type of power supply must be connected.
Check that the mains voltage corresponds to this, all other voltages than specified; the light effect can be
irreparably damaged. The product must also be directly connected to the mains and may be used. No
dimmer or adjustable power supply.
DISPLAY
Via the Menu key, you can adjust the desired settings. After pressing the menu, the display shows the following
settings:
1. Main Vol Out xxx%.
Adjust the manual volume output within the range of 0% to 100% by means
of the Up/Down keys.
2. Interval Set xxxS
Adjust the interval between each fog emission within the range of 1 to 100S
by means of the Up-/Down keys.
3. Duration Set xxxS
Adjust the duration of each fog emission within the range of 1 to 100S.
4. Volume Out xxx%
Adjust the volume output during the timer function within the range of 0-
100%
5. DMX 512 #xxx
Adjust the DMX address for DMX control.
6. Wind For Class xx
NO FUNCTION for this model.
7. Angel Set xx%
NO FUNCTION for this model.
8. LED Pro Set xx
Adjust the LED program within the range of 0 to 11.
Congratulations to the purchase of this product. Please read this manual thoroughly prior to using the product
in order to benefit fully from all features.
Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take
all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician
in order to avoid electrical shock. Keep the manual for future reference.
This mark attracts the attention of the user to high voltages that are present inside the housing and
that are of sufficient magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual
and that he should read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to
epileptic attacks should be aware of the effects that this light effect may have on them.
- Prior to using the product, please ask advice from a
specialist. When the unit is switched on for the first
time, some smell may occur. This is normal and will
disappear after a while.
- The unit contains voltage carrying parts. Therefore
do
NOT open the housing.
- Do not place metal objects or pour liquids into the
product. This may cause electrical shock and
malfunction.
- Do not place the product near heat sources such
as radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The product is not suitable for continuous use.
- Be careful with the mains lead and do not damage
it. A faulty or damaged mains lead can cause
electrical shock and malfunction.
- When unplugging the product from a mains outlet,
always pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged,
they need to be replaced by a qualified technician.
- If the product is damaged to such an extent that
internal
parts are visible, do NOT plug the unit into a mains
outlet and DO NOT switch the product on. Contact
your dealer. Do NOT connect the product to a
rheostat or dimmer.
- To avoid fire and shock hazard, do not expose the
product to rain and moisture.
- All repairs should be carried out by a qualified
technician
only.
- Connect the product to an earthed mains outlet
(220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the product will not be
used for a longer period of time, unplug it from the
mains. The
rule is: Unplug it from the mains when not in use.
- If the product has not been used for a longer
period of time, condensation may occur. Let the unit
reach room temperature before you switch it on.
Never use the product in humid rooms or outdoors.
- During operation, the housing becomes very hot.
Do not touch it during operation and immediately
after.
- To prevent accidents in companies, you must follow
the applicable guide lines and follow the instructions.
- Secure the product with an extra safety chain if the
unit is ceiling mount. Use a truss system with clamps.
Make
sure nobody stands in the mounting area. Mount the
effect at least 50cm away from inflammable material
and leave at least 1 meter space on every side to
ensure sufficient cooling.
- This product contains high intensity LEDs. Do not look
into the LED light to prevent damage to your eyes.
- Do not repeatedly switch the product on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not
leave the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice
from
a specialist.
- Only operate the product with clean hands.
- Do not force the controls.
- If the product has fallen, always have it checked by
a qualified technician before you switch the product
on again.
- Do not use chemicals to clean the unit. They damage
the varnish. Only clean the product with a dry cloth.
- Keep away from electronic equipment that may
cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the product off prior to unplugging it from the
mains and/or other equipment. Unplug all leads and
cables prior to moving the product.
- Make sure that the mains lead cannot be damaged
when
people walk on it. Check the mains lead before every
use for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if
power outlet match. If you travel, make sure that the
mains
voltage of the country is suitable for this product.
- Keep the original packing material so that you can
transport the product in safe conditions
Electric products must not be put into household waste. Please bring them to a recycling center. Ask
your local authorities or your dealer about the way to proceed. The specifications are typical. The
actual values can slightly change from one unit to the other. Specifications can be changed without
prior notice.
Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has
an appropriate electrical ground to avoid the risk of electrocution or fire.