Audio enhancement XD SOLO User manual

XD SOLO®
QUICK START GUIDE
MP3 Player and
Bluetooth Indictor
ALD Line Output
Voice Override Button
Charging Power Connector
Microphone*
Linking Button
Tone Controls
Line Audio In
Battery Level Monitor
Power Switch
Master Volume
Set at 12 o’clock or higher
1” Tweeter
8” Woofer

2
LINKING XD TEACHER
MICROPHONE TO THE XD SOLO®
1. With the microphone o, press the Link
button on the back of the XD Solo®
(Large red button).
2. Press and hold the PWR/MUTE and REC
buttons on the Teacher Microphone until
the microphone links.
3. Successful microphone linking will produce a beep through the system, and the BATT
LED on the microphone will glow green.

3
LINKING XD STUDENT
MICROPHONE TO THE XD SOLO®
1. With the microphone o, press the Link
button on the back of the XD Solo®
(Large red button).
2. While holding, use your thumb to
slide the TALK button up into to the
on position.
3. Successful microphone linking will produce a beep through the system, and the BATT
LED on the microphone will glow green.

4
REMOTE VOLUME CONTROL
OF MICROPHONES
XD TEACHER MICROPHONE (OWN)
LEVEL ADJUSTMENT
Press either the UP or DOWN arrow button to
increase or decrease the volume level of the Teacher
Microphone. A blue LED over the OWN (for own
microphone) will flash with each press.
XD STUDENT MICROPHONE
(OTHER) LEVEL ADJUSTMENT
To adjust the XD Student Microphone (OTHER) volume,
first press the SELECT button so that the LED over
the OTHER label comes on. Now press the UP/DOWN
buttons to control the level of the OTHER microphone.
Volume Up
Volume Down
The SELECT button determines which level will be
controlled by the UP/DOWN buttons.

5
BATTERY REPLACEMENT
Make sure the power cable is unplugged and the power switch is in the OFF position before
changing the batteries. Only replace with batteries that are the same size and rating as the
original (12V - 2.8 AH Sealed Lead Acid).
1. On the back of the XD Solo®, you will see a large black
plate. Remove the 4 screws around the edge of the plate.
2. Once you remove the plate, carefully pull the batteries out
far enough to reach the wires. Notice that wires are color
coded red for the Positive(+) terminal and black for the
Negative(-). Carefully pulling on the wire clip, detach the
wires from one battery and reattach to the same terminals
on the replacement battery. Repeat this step for the next
battery. This is easiest with needle nose pliers.
3. When sliding the batteries back into the compartment,
watch to make sure the wires do not pull away from the
battery’s terminals. If this occurs, gently push the connector
with a link pair of pliers to get a tighter fit.
4. Although the replacement batteries are charged, it’s still
suggested to charge the XD Solo for at least 12 hours
before use.
REMINDER
A good tip to prolong the life of your batteries is to leave the XD Solo plugged into AC power
when not in use. This will ensure you always have a fully charged unit and will prevent the
batteries from self-discharging. The XD Solo has an overcharge circuit so leaving the unit
plugged in will not hurt the batteries or the unit.

AudioEnhancement.com · 800.383.9362
DC-40615.03
BLUETOOTH PAIRING
1. Press the power/MODE button to activate
the Bluetooth function. Press the power/
MODE button again to turn the Bluetooth
function o.
2. When the Bluetooth function is activated
successfully, the screen will show
“Bluetooth Disconnected”, then it is ready
to pair.
3. Activate the Bluetooth connection on any
Bluetooth capable device.
4. Find the device name “TQ8” on the
pairing list to connect the device.
5. When the paring is successful, the
speaker will emit a tone and the screen
will show “Connected.”
6. The speaker is ready to stream audio
from the device.