Audio Note M2 Phono Balanced Technical manual

!
M2 Phono
Balanced
!
PRE AMPLIFIER
!
OWNER’S INFORMATION
!

1) IMPORTANT SAFETY INFORMATION
2) CE DECLARATION OF CONFORMITY
DISPOSAL
POWER REQUIREMENTS
3) INTRODUCTION
4) OVERVIEW
5) UNPACKING AND INSTALLATION
6) CONNECTION
9) OPERATION
11) TECHNICAL SPECIFICATIONS
12) WARRANTY INFORMATION
13) CONTACT INFORMATION
CONTENTS
!

OTHER SAFETY PRECAUTIONS: -
Never touch the power cord with wet hands.
Always remove the power cord by grasping the plug, not the cable.
Never expose the unit to excessive heat or magnetism.
Never let an inexperienced person repair or reassemble the unit.
Never put anything, especially metal objects, inside the unit.
Never place excessive weight on the unit.
!
Do not store or operate this unit in areas of high humidity or in close
proximity to water / moisture.
Do not expose or immerse the unit in liquid of any kind.
!
This product generates high levels of heat. Adequate ventilation must
be provided. Do not restrict airflow through any ventilation slots or
place the unit on any surface that may restrict airflow.
Valve equipment operates at extremely high temperatures;
KEEP OUT OF THE REACH OF CHILDREN AND ANIMALS.!
RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING
VOLTAGES ARE LETHAL!
Do not remove top cover, unless specifically instructed to do so in the user
manual.
This unit contains fuses and other safety components in accordance with
BS60065 requirements.
In the event of failure, replacement fuse or safety component must be of
the same part type and value.
!
This product must be earthed –ensure that the mains supply cable earth /
ground is correctly connected.
!
SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A
QUALIFIED SERVICE TECHNICIAN.
Do not attempt to replace any fuses without first disconnecting the unit
from the mains electricity supply.
! IMPORTANT SAFETY INFORMATION !

POWER REQUIREMENTS
Power requirements for electrical equipment vary depending on your geographical
location. Please ensure that your unit meets the power requirements in your area.
The power requirement for your unit is marked on the serial number plate, located on
the rear panel.
If you are in doubt, please contact your dealer before plugging the unit into the mains
supply.
CE DECLARATION OF CONFORMITY
DISPOSAL
This product must not be disposed of as normal household waste. To
prevent possible harm to the environment please separate the product
from other waste to ensure that it can be recycled in an environmentally
safe manner. Please contact your retailer or the appropriate local
government office for collection facilities.
!
We declare under our sole responsibility that this product is in conformity
with the following standards or standardized documents:
BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC
(from 1 January 1997)
CE 94
Peter Qvortrup,
Director
Audio Note (UK) Limited
25 Montefiore Road
Hove
East Sussex
BN3 1RD
United Kingdom
Tel: [phone]
Fax: [phone]
!

Thank you for purchasing this Audio Note (UK) product. With the correct care it
should give you many years of pleasure and enjoyment.
Please take the time to read all of the information in this manual before connecting
your new component to an electrical supply or your system, to ensure both your
safety and satisfaction.
Please note that due to our desire to continually improve products, specifications are
subject to change without notice. Therefore it is important to refer to the manual that
is supplied with your product for the most accurate information; manuals downloaded
from our website or obtained from other sources may no longer fully apply to your
product.
If you have any questions regarding the information contained within this document
or your new component, please feel free to contact us: -
Audio Note (UK) Limited
25 Montefiore Road
Hove
East Sussex
BN3 1RD
United Kingdom
Tel: [phone]
Fax: [phone]
e-mail: [email protected]o.uk
INTRODUCTION

Congratulations on your purchase of the Audio Note (UK) M2 Phono Balanced Pre
Amplifier.
It has been specifically engineered for sonic performance rather than technical
specification, and fulfills all Audio Note (UK) Level 2 criteria: -
Pure Class A operation
Zero negative feedback
Single Ended circuit topology
Valve rectification
Materials and component quality
It is well known that the accurate reproduction of music, not just sound, requires the
purity of the incoming signal to be preserved. It is therefore not difficult to conclude
that, in order to achieve this goal and to retain the musicality of the original
performance,the complexity of the circuitry itself must be kept to a minimum.
In response to this, the M2 Phono Balanced Pre Amplifier uses a single-ended, zero
feedback circuit topology. This is simply the most linear design possible, demanding
pure Class A valve operation and removing the need for a phase splitter, which
introduces unnecessary crossover distortion.
In contrast to the majority of the audio industry, we design our circuits with the aim of
minimizing non-harmonic and time base anomalies, rather than producing
vanishingly small harmonic or low intermodulation distortion measurements. These
non-harmonic amplitude and time base distortions have a highly perceptible and
adverse affect on the signal waveform, and it is far more important to address these
factors than participate in the increasingly irrelevant numbers game that chases
‘perfect measured response’.
As a result, the M2 Phono Balanced was designed for maximum linearity and
minimum transient distortion, and avoids the need for detrimental ‘corrective’
measures, such as inherently error-prone feedback loops.
The M2 Phono Balanced Pre Amplifier features a pair of 5814a valves for the line
stage, an ECC83 and 6DJ8 Moving Magnet phono stage, and a valve rectified power
supply incorporating a 6X5 and an ECL82. It also has a correctly designed and
implemented balanced output circuit.
M2 PHONO BALANCED PRE AMPLIFIER

Please take care when unpacking your M2 Phono Balanced Pre Amplifier. Choose a
clean, clear location to unpack your unit. Be aware that the Pre Amplifier is quite
heavy; before attempting to unpack or lift the unit, check the weight and if necessary
use more than one person so that it can be moved safely and easily.
We recommend that you retain and carefully store all of the original packing
materials, in case transportation / shipping is required at a later date.
Select a suitable location for the unit. This should be a dry, dust free and level area,
preferably shielded from direct sunlight and free from vibration. Also ensure that the
location is stable and capable of carrying the weight of the unit.
A suitable mains power outlet must be close to the location; power cords must not be
pulled or stretched tightly in an attempt to reach a wall socket. If the power cord will
not easily reach the socket, choose a closer location!
Please ensure that adequate ventilation for the unit is provided, and that airflow
through any ventilation slots in the unit is not restricted. We recommend a distance of
at least 20cm free space is maintained above the unit. Please also remember that
valve equipment operates at extremely high temperatures, so a position that is
inaccessible to children or animals is essential.
UNPACKING AND INSTALLATION

Phono input The M2 Phono Balanced is equipped with a high quality, valve,
Moving Magnet (MM) phonostage. Connect the cables from your
tonearm to the ‘Phono’ socket inputs. If your turntable is equipped with
a separate earth wire, connect this to the dedicated grounding / earth
post, located on the rear panel.
If you wish to use a low output Moving Coil (MC) cartridge, Audio Note
manufactures a series of Step Up Transformers for this purpose. For
further information, please contact your Audio Note (UK) Dealer, or
alternatively please contact us direct.
Line inputs Three line inputs are available labeled CD, Tuner and Aux. Any
standard ‘line level’ source can be connected to these inputs.
Connect the ‘Rec-Out’ or ‘Line Out’ sockets on your recording device
to the ‘Tape In’sockets of the M2 Phono, Balanced and the ‘Tape Out’
sockets to the ‘Rec-In’ or ‘Line In’ sockets of your recording device.
Ground Post A ground post is provided for connection to those source components
that also use a separate ground terminal.
Mains The M2 Phono Balanced Pre Amplifier utilizes an IEC 320 mains inlet
socket. Use the supplied mains cable to connect the unit to the local
mains supply. The mains fuses are located in separate fuse holders,
situated on the rear panel.
Special Note –Make sure that all connectionsare tight and clean. For
best results use good quality audio interconnects. Although it is
perfectly acceptable to use cables manufactured by other companies,
for best results and performance, we recommend our own Audio Note
(UK) range of interconnects and loudspeaker cables. For further
information, please consult your nearest Audio Note (UK) dealer, or
alternatively please feel free to contact us directly.
Outputs The M2 Phono Balanced provides two unbalanced outputs, consisting
of two pairs of colour coded RCA / Single Ended sockets. RED is for
RIGHT channel connection, WHITE is for LEFT channel connection.
There is also a balanced output, consisting of a pair of ‘male’ XLR
sockets (see ‘Balanced’ section, below).
RCA The two pairs of RCA / Single Ended outputs are for connection to a
power amplifier and are identical, making them suitable for bi-amping.
CONNECTION
RCA SOCKET,
CENTRE = POSITIVE / SEND.
RCA SOCKET,
SHELL = NEGATIVE / RETURN.

3
Balanced The M2 Phono Balanced is equipped with custom designed and
manufactured output transformers, which utilize an improved output
and grounding scheme to provide the best possible connection to the
power amplifier.
Below is a description of the various cable and connection options: -
The pin configuration for all Audio Note (UK)
XLR / BALANCED connections is as follows: -
PIN 1 Ground / Shield
PIN 2 Positive / Send
PIN 3 Negative / Return
CONNECTION continued…
XLR MALE
OUTPUT
1
2
3
RCA
OUTPUT
SOCKET
BALANCED /
SINGLE ENDED
SWITCH

CONNECTION continued…
CABLE CONFIGURATION OPTIONS
CONVENTIONAL: SCREEN CONNECTED AT BOTH ENDS
XLR FEMALE
XLR MALE
3
1
1
2
2
3
SCREEN
PREAMP OUTPUT
POWER AMP INPUT
SCREEN CONNECTED AT PREAMP END ONLY, TO
ELIMINATE GROUND LOOPS
3
2
1
2
1
3
SCREEN
XLR FEMALE
XLR MALE
PREAMP OUTPUT
POWER AMP INPUT
CABLE CONFIGURATION FOR XLR BALANCED PREAMP
OUTPUT TO RCA UNBALANCED AMPLIFIER INPUT
2
1
3
SCREEN
XLR FEMALE
RCA MALE
PREAMP OUTPUT
POWER AMP INPUT