Audiolab 8000S User manual

8000S
Integrated Amplifier
User Instructions
Audiolab
IAG House,
Sovereign Court,
Ermine Business Park,
Huntingdon PE29 6XU
Tel: [phone]
Fax: [phone]

Mains supply and safety
Important notice to UK users
Mains Supply:
Power Cord:
The mains operating voltage of all Audiolab units is
shown on the rear panel. If this does not match the voltage in your area,
consultyourdealer.
The mains supply fuse is located on the rear panel of the unit. If it has
broken, check for any obvious cause before replacing the fuse with one of
thecorrectratingandtype.Thefusevaluesare:
220-240V(UK,Korea,etc.) T2.5AL 20mm SlowBlow
100-120V(USA, Japan, etc) T4.0AL 20mm SlowBlow
The fuse is located in a slide-in
carrier which also contains a spare
fuse. The fuse carrier can only be
pulled out after the IEC power cord is
unplugged. When the carrier is
opened the first fuse to be seen is the
spare fuse. Remove and safely
dispose of the fuse with the blown
linkbeforereplacingit.
Class II construction double insulated. This product must not be
connectedtoearth.
An AC power cord is normally supplied with a mains plug
suitable for your area. If you have any doubts, consult your dealer about
obtainingasuitablepowercord.
The appliance cord is terminated with a UK approved mains plug fitted
with a 5A fuse. If the fuse needs to be replaced, an ASTA or BSI approved
BS1362 fuse rated at 5A must be used. If you need to change the mains
plug, remove the fuse and dispose of this plug safely immediately after
cuttingitfromthecord.
Connecting a Mains Plug
Thewiresinthemainsleadarecolouredinaccordancewith the code:
Blue:NEUTRAL; Brown: LIVE:
As these colours may not correspond to the coloured markings identifying
theterminals in your plug, proceed as follows:
The BLUE wire must be connected
to the terminal marked with the
letter N or coloured BLUE or
BLACK. The BROWN wire must be
connected to the terminal marked
with the letter L or coloured
BROWNor RED.
2.5A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
Fuse Carrier
IEC Mains Connector
4 ead these instructions.
Keep these instructions. In the event that you pass the product to a third
partythisinstructionmanualshouldbeprovidedalong with the product.
Heedallwarnings.
Followallinstructions.
Donotusethis apparatus nearwater.
Cleanonlywithdrycloth.
Donotblockanyventilation openings.
Installinaccordancewiththemanufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves,orotherapparatus(includingamplifiers)thatproduceheat.
Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
theobsoleteoutlet.
Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Useonlyattachments/accessoriesspecifiedbythemanufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatuscombinationtoavoidinjuryfromtip-over.
Unplug this apparatus during lightning storms or when unused for long
periodsof time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture,doesnotoperatenormally,orhas been dropped.
To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture. The product must not be exposed to dripping
and splashing and no object filled with liquids such as a vase of flowers
shouldbeplacedonthe product.
No naked flame sources such as candles should be placed on the
product.
Changes or modifications not expressly approved by the
manufacturercouldvoidtheuser's authority to operate this device.
This equipment has been tested and found to comply with the limits for a
Class B digitial device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
or television reception, which can be determined by tuning the equipment
off and on, the user is encouraged to try to correct the interference by one
ormoreofthe following measures:
Re-orientate or re-locate the receiving antenna. Increase the separation
between the equipment and the receiver. Connect the equipment into an
outletonacircuit different from that to which the receiver is connected.
Consultthedealeroran experienced radio/TV technician for help.
The batteries supplied with this unit should be treated
with care and not punctured or damaged. Used batteries should be
disposed of in full conformity with recycling regulations in your area.
NEVERdisposeofbatteriesina fire or in the general rubbish.
Warning:
Caution:
Important Note:
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ADVERTISSEMENT : RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
This symbol indicates that there are important
operating and maintenance instructions in the
literatureaccompanyingthisunit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
withinthisunit.
1: Statutory & Safety Information
Rated Output Power
Inputs
Gain
Signal To Noise Ratio
Frequency Response
Total Harmonic Distortion & Noise
Channel Balance
Channel Separation
Crosstalk
Polarity (phase)
Pre-amp Output
Headphone Output
Record Output
Muting
Accessories Supplied
Colour
Operating Temperature Range
Power Requirements
Dimensions
Weight
60 W (18 dBW) per channel into rated load impedance (8 Ohms)
withbothchannelsdriven
CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2: 125mV/20k IHF
POWERAMP:782 mV/47 k
PRE-AMP:9dB@ 1 kHz
POWERAMP:29.0 dB @ 1 kHz.
CD,TUNER, AUX,VIDEO,TAPE1, TAPE2:
Betterthan80dB(IHF,rel.0.5 V pre-ampoutput)
POWERAMP:better than 80dB(IHF, rel. O dBW)
CD,TUNER, AUX,VIDEO,TAPE1, TAPE2 and POWER AMP:
20Hz-20kHz ±0.5 dB: 1 Hz-65 kHz -3 dB.
Lessthan0.07%
Within1dB
Betterthan60dB @ 1 kHz any input
Betterthan80dB @ 1 kHz
Non-invertingforallinputsandoutputs
PREOUT1 and PRE OUT 2: Output Impedance 100
MaximumOutput>7.3V RMS
Outputimpedance:330
(Suitableforheadphones8 -2k impedance)
VIDEOOUT,TAPE1 OUT,TAPE2 OUT:
Outputimpedance:1k .
Gainfrominputto record output 0 dB (x1)
Mutingcontrolledmanuallyorautomatically
ACPowerCord
InstructionManual
8000RCRemoteControl with 2 x AA batteries
Silver
10-35°C
(DependingonRegion)
50-60Hz 100 V, 110-120 V, and 220-240 V models available
MaximumPowerConsumption: 440VA
(WXHXD)
445x74x335mm-including feet, terminals and controls
445x64 x 302 mm- excluding feet, terminals and controls
Net:7.4kg
Shipping:8.8kg
Audiolab reserves the right to alter design and specification
withoutnotice.Specificationmayvaryfordifferent countries.
Audiolabisamember of the International Audio Group.
9
9
9
999
9
6: Specifications 8000S
Power Amplifier Protection Circuits
Short Circuit Protection:
DC Offset Protection:
Thermal Protection:
If the output terminals are connected together or there
is a short caused by a faulty speaker or connecting lead, the amplifier will mute and
un-muteuntilthefaultcondition is removed.
If there is an internal or external fault which may cause DC
voltage to be presented to the loudspeaker, the amplifier will mute and stay muted
untilthefaultis removed.
If the amplifier is driven excessively for long periods, or the
output devices are pushed beyond their safe operating area, the amplifier will
switchoffand then switch back on again when it has cooled down.
Inallcases,ifthe amplifier does not respond to remedial action, consult your dealer.

Volume
Press to raise or lower the volume. The
VOLUMEcontrol on the front panel turns.
Unpacking
Inserting Batteries in the Handset
Controls And Functions
Unpacktheproductfully.The carton should contain
TheAudiolab8000Sintegrated amplifier
OneIECpower cord suitable for your area
OneRemoteHandset with two AA batteries
Thisinstructionmanual.
If any item is missing or damaged report this to your dealer as
soonaspossible.
Retain the packing for future safe transport of your amplifier. If
you dispose of the packing, do so with regard to any recycling
regulationsinyourarea.
Thebatterycompartmentisonthe rear of the handset. Unwrap the
batteries, open the compartment cover and insert the batteries.
Followthepolarityindicationsinthe battery compartment.
Always replace batteries in pairs. Use new batteries of the same
typeandrating,ideally from the same manufacturer.
When power is switched on the 8000S is muted for 8 seconds.
Alwaysswitchthepoweroff before changing connections.
Turn to select the listening source. The 8000S mutes briefly when a
newinputisselected.
Adjustsplayingvolume.Alwaysturnthevolume up gradually.
Turn to select source to record to Tape 1, Tape 2 or Video. The
connections can also be used to connect to any recorder with
analogueinputssuchasa CD,MP3, DATrecorder,etc.
Record selector and input selector operate independently. It is
possibletorecordfrom any source whilst listening to another.
Select integrated when using 8000S as an integrated amplifier.
Select mute to turn off pre-amplifier outputs, loudspeakers or
headphones.Seesection4 for further details.
Socket for connection of headphones. Unplug headphones when
not in use. Connecting headphones mutes the loudspeakers and
disconnectsthepre-amplifier outputs and power amplifier inputs.




Power Switch
Input Selector
Volume Control
Record Selector
Mode Switch
Headphone Socket
2: Introduction
5: Service and Warranty
RECORD
SELECTOR
INPUT
SELECTOR
MODE
SWITCH
VOLUME
CONTROL
HEADPHONE
SOCKET
POWER
SWITCH
POWER LED
RED=Power On
MUTE LED
RED=Mute On
REMOTE
CONTROL SENSOR
Input
Press to select listening source. The INPUT
selectoronthe front panel turns.
If you wish to record, the record input must be
selectedmanually.
Mute
Toggles mute On/off. Does not function if the
MODEswitchonthe front panel is set to mute.
Remote Handset
Buttonsshowninwhite control the 8000S.
Buttons shown in grey operate Audiolab CD
playersandhavenoeffect on the 8000S.
As the handset uses RC5 coding it will operate
manyotherplayers.Checkwith your dealer.
Servicing
Servicing of Audiolab products should only be carried out by
authorised service agents. If service is required the equipment
should be returned, securely packaged, preferably using original
packaging,toyourdealer.
In the UK equipment may be returned to the IAG Service Centre. In
the USA equipment may be returned to the Service address shown
onthispage.
Alwaystelephonebeforereturninganyequipment.
A note should be enclosed giving your name, address, telephone
number, and a brief description of the reason for return.
If you require Service outside the Warranty period, do not hesitate
tocontactyour dealer.
While cleaning is in progress the AC power cord must be
unpluggedfromtheACpower supply socket.
Any grease or dirt on the equipment may be removed with a soft,
lint-free cloth slightly moistened with a mild solution of warm
water and detergent or washing-up liquid. Do not use any other
solutionsorsolvents.
Retainoriginal packagingfortransportingequipment.
If you have any queries regarding the use of Audiolab equipment,
consultyourdealer.
Service Addresses, UK & USA
IAG Service Centre
Unit 4
St Margaret’s Way
Stukeley Meadows Industrial Estate
Huntingdon
Cambs
PE29 6EB
452561
13403
England
Tel:[phone]
Fax: [phone]
IAG America, Inc.
15 Walpole Park South
Walpole
MA 02081
Tel: [phone]
Fax [phone]
USA
Audiolab limited warranty
Audiolab Ltd. warrants this product, subject to the terms and
conditions below, to be free from defects in materials and
workmanship. During the warranty period Audiolab will repair or
replace (at Audiolab's option) this product, or any defective part in
this product, if it is found to be defective due to faulty materials,
workmanship or function. The warranty period may vary from
countrytocountry.
The warranty starts on the date of purchase (or the date of delivery
ifthisis later).
You must provide proof of purchase / delivery before work can be
carried out. Without this proof, any work carried out will be
chargeabletoyou.
All work will be carried out by Audiolab or its authorised agents or
distributors. Any unauthorised repair or modification will void this
warranty.
If any part is no longer available it will replaced with a functional
replacementpart.
Anypartsthatarereplaced will become the property of Audiolab.
Any repair or replacement under this warranty will not extend the
periodofwarranty.
Thiswarranty is valid only in the country of purchase, applies only to
thefirst purchaser and is not transferable.
Products on which the serial number has been removed,
alteredorotherwisemade illegible.
Normalwearandtearand cosmetic damage.
Transportation or installation of the product.
Accidental damage, faults caused by commercial use, acts of
God, incorrect installation, connection or packaging, misuse,
neglect or careless operation or handling of the product which
isnotin accordance with Audiolab's user instructions.
Equipment that has been operated in conjunction with
unsuitable,inappropriateorfaultyapparatus.
Repairs or alterations carried out by parties other than
Audiolaboritsauthorised agents or distributors.
Productsnot purchased from an Audiolab authorised dealer.
Productsthat were not new at the time of original purchase.
Productssold 'as is', 'as seen' or 'with all faults'.
Repairs or replacements as provided under this warranty are the
exclusive remedy of the consumer. Audiolab shall not be liable for
any incidental or consequential damages for breach of any express
or implied warranty in this product. Except to the extent prohibited
by law, this warranty is exclusive and in lieu of all other warranties
whatsoever, both express and implied, including, but not limited
to, the warranty of merchantability and fitness for a practical
purpose.
This warranty provides benefits that are additional to and do not
affectyourstatutory rightsasaconsumer.
Some countries and US states do not allow the exclusion or
limitation of incidental or consequential damages or implied
warranties so the exclusions in the paragraph above may not
apply to you. This warranty gives you specific legal rights, and you
may have other statutory rights, which vary from state to state or
countrytocountry.
To obtain warranty service contact the Audiolab authorised dealer
from which you purchased this product. Do not despatch goods
without the prior agreement of the dealer, Audiolab or their
authoriseddistributors.
If asked to return products for inspection and/or repair, pack
carefully, preferably in the original cartons or packaging affording
an equal degree of protection, and return prepaid. If unsuitable
packaging is used, Audiolab may make a charge for the supply of
newpackaging.
Insurance is recommended as goods are returned at owner's risk.
Audiolab or their authorised distributors cannot be held liable for
lossordamage in transit.
Packing, insurance and freight on the return journey will be paid by
Audiolab or their authorised agents or distributor if corrective work
provesto benecessary.
Terms and conditions:
The following are not covered:
How to claim:










3: Input & Output Connections
Pre-Power Mode
Pre Mode
Pre-Power AV
The pre-amplifier section is internally connected to the power
amplifier. The pre-amplifier outputs areoperational.
A powered subwoofer can be connected to the pre-amplifier
outputs
A second power amplifier can be connected for bi-amplifying as
showninthediagram.
An additional power amplifier can also be connected to drive a
secondpairofspeakersin a remote location.
All signals to and from the power amplifier of the 8000S are
disconnected. In this mode, the 8000S functions as a stand-alone
pre-amplifier.
The pre-amplifier section of the 8000S can be connected to a
stereopoweramplifier, or to two monobloc amplifiers .
The pre-amplifier and power amplifier sections operate
independently. This mode can be used to connect a multichannel
AVprocessor.
The processor should be connected via any spare tape output or, as
analternative,oneofthe pre-amp outputs.
4: Operation
LOUDSPEAKER TERMINALS
MAINS
INPUT
RIGHT LEFT
FUSE
HOLDER
POWER
AMPLIFIER
INPUT
PRE-
AMPLIFIER
OUTPUTS TAP E 2 TAP E 1
VCR AUX
CDR,ETC
CD, DVD
Signal Connections
CD, TUNER, AUX, VIDEO IN, TAPE 1 IN, TAPE 2 IN
VIDEO OUT, TAPE 1 OUT, TAPE 2 OUT
PRE-AMP OUT 1 & 2
POWER AMP IN
LOUDSPEAKER TERMINALS
GROUND
Thesixinputs may be used for connecting any line level source.
Three sets of record outputs for connection of up to three stereo
audio recorders, e.g. tape recorder, CD recorder, audio recording
inputofVCR,DVD,MP3, MiniDisc recorder,etc.
Low impedance (100 ohm) pre-amplifier outputs for driving
external power amplifiers, sub-woofers or signal processors. Long
cables may be used if required. Pre-amp outputs are switched off
whenintegratedmodeisselected or whenever amplifier is muted.
For driving the power amplifier input directly from an external
source.Onlyoperateswhen pre power AV mode is selected.
Two sets ofloudspeakeroutput terminals connected in parallel.
Use only if phono pre-amplifier and turntable are used and both
are Class II double insulated (no earth connection). In this case the
ground terminal can be connected to the metalwork of these units
to eliminate residual hum. The ground terminal must not be used
asasafety earth. If in doubt consult your dealer.
Connecting Loudspeakers
Switchpoweroffwhen connecting loudspeakers.
Usegoodquality lowresistanceloudspeakercable.
Connect the Positive RED (+) terminal of the
amplifier to the Positive (+) RED terminal of the
loudspeaker. Connect the Negative (-) BLACK
terminalssimilarly.
When connecting loudspeakers tighten the
terminalssecurelybyhand.
Make there are no loose strands of wire which could
causeshorts.
Standard Loudspeaker Connection
You can connect a speaker switching box or headphone adaptor to the unused set of speaker terminals
Loudspeaker bi-wiring offers improved sound quality because high and low frequency signals are carried
individually to the loudspeaker drive units.
Connecting
Cables
Operating Modes
Although the 8000S is an integrated amplifier, it can function as a separate pre-amplifier and
poweramplifier. This allows the unit to be used in a variety of stereo and multichannel modes.
NOTE: When switching modes, the making and breaking of connections may momentarily
operatethemutingfunctionon the 8000S.
The pre-amplifier section is internally connected to the power amplifier. Pre-amp outputs are
notoperational.Externalsubwoofers,processors,oramplifiers will not receive any signal.
Integrated Mode
Bi-Wired Loudspeaker Connection
OUTPUTS INPUT
SPKRS
A/V PROCESSOR
--ACTIVE-
OPERATIONAL
-ACTIVEACTIVE
OPERATIONAL-ACTIVE-
OPERATIONALACTIVE--
-ACTIVE--
LOUDSPEAKERS
PRE-POWER
INTERNAL LINK
PRE-AMP OUT 1&2POWER AMP IN
Switching On
Makesure all the connections to and from the amp are secure and correct.
Makesure the operating mode is correctly set.
Plug the power cord into the wall socket and the amplifier. Switch on at the mains
andthenswitchon the 8000S. The power indicator lights. The unit is operational.
Theamplifiermaybeoperated via the front panel or the remote handset.
NOTE: Selecting MUTE from the front panel will disable the mute function on the
handset.To restorenormaloperation,selectanoperatingmode.
RED
BLACK
Speaker
Cables
7mm
20mm