Audiolab 8200P User manual

8200P

8200P
VERSION HISTORY
Rev
V01
Date Update Content
2011.06.14 First Version

CONTENT
8200P
Introduction
ia
screen of Bottom
Assembly Parts List
Electronic Parts List
/
Specification
Assembly Sketch
Schematic Diagram
Wir ng Di gram
Silk Top
Maintenance Alignment Procedure
1
2
3
4
5
6
7
8
9
.
.
.
.
.
.
.
.
.
1
2
3
4-8
9
10-11
12
13-14
15-19

INTRODUCTION
1
8200P
No part of this document may be reproduced or transmitted in any form or by any means,electronic or
mechanical, for any purpose, without the express written permission of International Audio Group
Limited (IAG)
This manual is for the exclusive use of IAG, its approved distributors and approved UK service agents.
No part of this manual shall be transferred to any other party without the express written permission of
IAG.
It is the responsibility of the user to ensure that all the information contained in this manual is current.
Notification for new issues of this manual and minor updates will be given via the IAG web-site or on
request.
This manual has been prepared with the greatest care, it is intended for information only and no liability
shall be accepted for errors or changes to specification.
For further service information, parts lists and updates, please contact our web-site at
www.international audio group.com .
2011 International Audio Group Limited. All rights reserved.
C

SPECIFICATION
2
8200P
Rated Output Power 100W (20dBW) /Channel into 8 both channels drive
n
Inputs Sensitivity 1V rms for 100W into 8
Input Impedance: 50k
Load Connected in parallel with INPUT
Gain 29.0 dB at1kHz
Signal To Noise Ratio(IHF, rel. 0.dBW)Better than 95 dB
Frequency Response 20 Hz-20 kHz ±0.3 dB
0.1Hz-75 kHz -3 dB.
Total Harmonic Distortion&Noise Less than 0.05%
Channel Balance Within1dB
Polarity (Phase) Non-Inverting
Muting Muting controlled automatically
Operating Temperature Range 10-35 °C
Power Requirements(Depending on
Region)
50-60Hz 100V, 110-120V, and 220-230V models
available
Maximum Power Consumption:500 VA
Dimensions (W×H×D) 444×78×326mm
Weight Net: 8.4 kg Shipping: 9.8 kg

ASSEMBLY SKETCH
3
8200P

SCHEMATIC DIAGRAM
8200P
4
8200P-Mainboard-P1/5
C358 10NF
OV
C358 10NF
OV
A01

SCHEMATIC DIAGRAM
5
8200P
8200P-Mainboard-P2/5

SCHEMATIC DIAGRAM
6
8200P
8200P-Mainboard-P3/5

SCHEMATIC DIAGRAM
7
8200P
8200P-Mainboard-P4/5

SCHEMATIC DIAGRAM
8
8200P
8200P-Mainboard-P5/5

WIRING DIAGRAM
9
8200P
8200P-Wiring Diagram-P1/1
Vio Bwn
/23 0V /11 5V
L=310MM L=310MM

10
SILK TOPSCREEN OF BOTTOM
/
8200P
8200P-MainBoard-Top Silkscreeen-P1/2

8200P
11
SILK TOPSCREEN OF BOTTOM
/
8200P-MainBoard-Bottom Silkscreeen-P2/2

MAINTENANCE ALIGNMENT PROCEDURE
12
Product Initial
setting
After 15
mins
After 30
mins
8200P 60 –65 24 – 25 21.5 – 22.5
All settings are mV dc.
Remarks：Also the test continues unil the bias is steady at the final value in the table.
3.Set bias as shown in table below.
4.The test continues until the bias is steady at the final value in the table.
For 8200M bias is measured across R148 (left channel) and R248 (right channel).
Audiolab 8200P Bias Procedure
This procedure must only be carried out after the unit has passed a full functional test .
1.Connect the unit to be biased to mains and switch on. The mains voltage should be set to 230VAC
± 2% or 120VAC ± 2% while the test is done.
2.Wait for the unit to power up.
8200P
Notes：
1.If the Bias Okay, switch off the unit and put "PASSED" mark on the unit.
Test condition: Vin = 1V, 1kHZ sine wave(Load: 8ohm) 1/8 Output Power Anti-ESD bell
Step transformer for
AC mains
AC100V AC110V±2%
3:Soak test with the condition above with 48 hours.
4. Check all the parameter within the spec.
AC220、230V AC240V±2%
AC110V AC120V±2%
unit rated voltage variac voltage
AC240V AC250V±2%
2: Ageing test
Mulitimeter
1):Power ON the unit the "ON" LED will lit and the "PROTECT" LED also lit
but will OFF after 5-10 second.
2):Add 5% of AC input for the test.
Ageing test step Equipment andTools
1: Equipment and Set up
1):Set the "RECORD" and "INPUT" knob to CD. "GAIN" set to 0dB position.
Volume set to Max.
8200P Ageing test step
8200P -Bias Procedure And Ageing test step-P1/1

ASSEMBLY PARTS LIST
13
8200P
8200P-Assembly Bom-P1/2
R/N P/N PART NAME DESCRIPTION QTY
1 300-1032410000R Front Panel finish and anodized aluminium 1
2215-1027410001R Button Cap painted 1
3215-1027410000R Power Button painted 1
4305-1027410002R Mains Switch
Bracket painted 1
5 500-3050240300AR Nut M3 Ni 11
6 263-0020100102R EVA 20*10*10mm EVA 1
7 309-1032410000R Chassis painted and silkscreen 1
8 588-3000066037R Screw M3*6 25
9 226-0230191911R Foot black 4
10 319-1027410001R Side Panel sand blast and anodized 2
11 307-1050800081R Nut gold plated 4
12 331-1031410001R PCB Terminal
Connector gold plated 4
13 331-1031410000R Terminal Connector gold plated 4
14 537-3002000306R Screw M3*10 2
15 513-6412150780R Washer Φ6.4XΦ12X1.5 NI 1
16 500-6000000300R Nut M6 1
17 302-1032410000R Top Cover sand blast and anodized
aluminium 1
18 534-3002061006R Screw M3*6 18
19 534-3002100606R Screw M3*10 11
20 306-1003770012R
Main
Radiator(Machning
ed)
anodized
1
21 306-1003770013R Main Radiator anodized 1
22 306-1003770001QR Radiator(1) anodized 1
23 306-1003770002QR Radiator(2) anodized 2
24 306-1003770003QR Radiator(3) anodized 4
25 308-1031410000R Transformer
Insulation Board black painted 1
26 231-2136000102R Rubber Washer Φ136*Φ10*1 2
27 348-1300300230R Copper Post nickel plated 2
28 231-2013005012R PVC Washer Φ12.5*Φ4.5*0.1mm 2
29 588-3000106037R Screw M3*10 1
30 223-0700220311R Insulation Post φ7.5*3.1mm,NYLON66(UL) 1

ASSEMBLY PARTS LIST
14
8200P
8200P-Assembly Bom-P2/2
Remark:Colour Difference Table
R/N P/N PART NAME DESCRIPTION QTY
300-1032410000R screened, light grey(silver anodized) 1
300-1032420000R screened, light grey(black anodized) 1
215-1027410001R silver painted,ABS757# 1
215-1027420001R black painted,ABS757# 1
215-1027410000R silver painted,ABS757# 1
215-1027420000R black painted,ABS757# 1
309-1032410000R silver painted 1
309-1032410001R black painted 1
319-1027410001R sand blasting,anodized silver 2
319-1027420001R sand blasting,anodized black 2
302-1032410000R sand blasting,anodized silver 1
302-1032410001R sand blasting,anodized black 1
534-3002061006R M3*6NI 20
534-3002060906R M3*6black 20
534-3002100606R M3*10NI 11
534-3002100906R M3*10black 11
588-3000106037R M3*10NI 1
527-3012100806R M3*10black 1
1 front panel
2 button cap
3 power button
7 chassis
10 side panel
19 screw
18 screw
29 screw
17 top cover

ELECTRONIC PARTS LIST
15
8200P
8200P-Electronic Bom-P1/5
R/N P/N PART NAME DISCRIPTION QTY LOCATION
1 046-9400000400R 909 Terminal red/black 4
2 062-5118000201R Mains Cable 2 meter American 1
3 041-1376000000QR Mains Switch SWITCH MAINS２P
SDDSA 3289A 1
4 071-1100000000R Tie Wrap 100MM YJ-100 20
5 044-1700000000QR Mains Inlet MAINS INLET 2 POLE 2
FUSE LOCS 1
6 742-3501000000R Heat Sink Φ35 black 0.1
7 060-4180310312R Double Insulated
Wire
UL1672 18 AWG blue
L=310MM 1
8 060-4180310112R Double Insulated
Wire
UL1672 18AWG brown
L=310MM 1
9 053-1020410152R Mains Switch
PCB
single layer PCB
MAINS SWITCH 200
SERIES
1
10 022-2000022348R Transformer
115V 50/60HZ Noratel
TI-103410 500AV D=139
Iss 1 SW/120ºC
1
11 031-2200813121HR Fuse Tube T5A/250V 213 5*20MM
LITTELFUSE 2
12 008-1003025005R Cap MKT 10NF/250V 10% 2
13 053-1374001104QR Mains Switch
PCB
PCB MAINS SWITCH
200 SERIES 1
14 019-0011022000QR LED LED RED 1
15 742-0301000000R Heat Sink Φ3 /BLK 0.2
16 742-1001000000R Heat Sink Φ10 / BLK 0.2
17 742-0501000000R Heat Sink Φ5/ BLK 0.05
18 742-1001000000R Heat Sink Φ10/ BLK 0.2
19 055-0302029333R Flat Wire 2P L=290MM UL1007
24# 1
20 088-1032410000R 8200P AMP
(Stereo) 8200P PCBA 1
21 053-103241A000R 8200P AMP
ISS5
single layer FR-4 KB
20Z blue /osp
414.5*162*1.6MM
1
22 001-6801205010QR Resistor 680R 1/4W 1% 12 R106.107.117.118.131.132
.206.207.217.218.231.232
23 001-2202205010QR Resistor 2K2 1/4W 1% 2 R116.226
24 001-5601205010QR Resistor 560R 1/4W 1% 9 R125.126.159.160.225.226
.259.260.311
25 001-3301205010QR Resistor 330R 1/4W 1% 2 R141.241
26 001-2203205010QR Resistor 22K 1/4W 1% 8 R137.138.152.153.237.238
.252.253

ELECTRONIC PARTS LIST
16
8200P
8200P-Electronic Bom-P2/5
R/N P/N PART NAME DISCRIPTION QTY LOCATION
27 001-1000205010QR Resistor 10R 1/4W 1% 4 R135.136.235.236
28 001-1803205010QR Resistor 18K 1/4W 1% 2 R108.208
29 001-1802205010QR Resistor 1K8 1/4W 1% 4 R150.151.250.251
30 001-1004205010QR Resistor 100K 1/4W 1% 5 R102.161.202.261.304
31 001-1005205010QR Resistor 1M 1/4W 1% 1 R314
32 001-1504205010QR Resistor 150K 1/4W 1% 2 R307.315
33 001-6803205010QR Resistor 68K 1/4W 1% 1 R317
34 001-1003205010QR Resistor 10K 1/4W 1% 3 R303.305.319
35 001-3304205010QR Resistor 330K 1/4W 1% 1 R320
36 001-5603205010QR Resistor 56K 1/4W 1% 1 R313
37 001-1001205010QR Resistor 100R 1/4W 1% 4 R129.130.229.230
38 001-4700205010QR Resistor 47R 1/4W 1% 4 R165.166.265.266
39 001-3302205010QR Resistor 3K3 1/4W 1% 1 R306
40 001-3902205010QR Resistor 3K9 1/4W 1% 6 R113.127.128.213.227.228
41 001-4703205010QR Resistor 47K 1/4W 1% 6 R139.140.239.240.312.318
42 001-8204205010QR Resistor 820K 1/4W 1% 2 R105.205
43 001-6802205010QR Resistor 6K8 1/4W 1% 1 R310
44 001-5600205010QR Resistor 56R 1/4W 1% 8 R144.145.109.209.244.245
.157.257
45 001-4701205010QR Resistor 470R 1/4W 1% 10 R110.111.154-
156.210.211.254-256
46 001-1801205010QR Resistor 180R 1/4W 1% 2 R158.258
47 001-1002205010QR Resistor 1K 1/4W 1% 6 R112.119.120.212.219.220
48 001-1002205014QR Resistor 1K 1/4W 1% 1 R309
49 001-2209205010QR Resistor 2R2 1/4W 1% 1 R316
50 001-2200205010QR Resistor 22R 1/4W 1% 4 R142.143.242.243
51 001-0470308050R Resistor 4.7Ω 2W J 4 R149.249.321.322
52 001-0000105050QR Resistor 0R 1/4W 5% 32 WL1-28.33-36
53 001-1101405010QR Resistor 110R 1/4W 1% 2 R115.215
54 001-3301409010QR Resistor 330R 1W 1% 2 R401.402
55 001-4701405010QR Resistor 470R 1/4W 1% 2 R122.221
56 001-1102405010QR Resistor 1k1 1/4W 1% 2 R162.262
57 001-3902405010QR Resistor 3k9 1/4W 1% 2 R104.204
58 001-1503405010QR Resistor 15k 1/4W 1% 2 R114.214
59 001-4703405010QR Resistor 47k 1/4W 1% 2 R103.203
60 001-8204405010QR Resistor 820k 1/4W 1% 2 R101.201
61 001-1502109050QR Cap 1K5 3W 5% 4 R123.124.223.224
62 016-1041110001HR Cap 0.1UF/100V 10% MKS4
10PCM WIMA WIMA 8C110- 112.115.210.211.212.215
63 016-1021132201QR Cap FKP2 1000PF/100V
2.5% WIMA PCM5 4 C108.109.208.209
64 016-4710832201R Electrolytic Cap 470pF 63V 2.5% 2 C103.203
65 006-4794051173HR Electrolytic Cap
ELNA 4U7 20% 63V
RE3-63V4.7ME3
5*11mm
4 C113.114.213.214

ELECTRONIC PARTS LIST
17
8200P
8200P-Electronic Bom-P3/5
R/N P/N PART NAME DISCRIPTION QTY LOCATION
66 006-1036508073QR Cap 10000U/63V +50/-20%
Φ35*80 4PCB
67 013-2250120505QR Cap 2U2 10% 50V MSK2
WIMA 4 C121.122.221.222
68 008-4703002517QR Transistor 0U047 +80/-20% 25V
5YF 2 C118.220
69 018-3200653115R Transistor ZTX653 TO-92 3 Q115.215.304
70 018-3200753115R Transistor ZTX753 TO-92 3 Q116.216.306
71 018-0101477113QR Transistor 2SA1477 PNP TO-
126ML SANYO 2 Q113.213
72 018-0303787113QR Transistor 2SC3787 NPN TP-
126ML SANYO 2 Q114.214
73 018-0101668111QR Transistor TRAN 2SA1668 PNP
TO-220F SANKEN 2 Q120.220
74 018-0304382111QR Transistor 2SC4382 NPN TO-220F
SANKEN 2 Q119.219
75 018-2700042115QR Transistor TRAN ZTX457 NPN TO-
92 6 Q117.125.127.217.225.227
76 018-2700092115QR Transistor TRAN ZTX757 P NP E-
Line 6 Q118.126.128.218.226.228
77 018-0302922110QR Transistor TRAN 2SC2922 NPN
MT-200 SANKEN 4 Q123.124.223.224
78 018-0101216110QR Zener Diode TRAN 2SA1216 PNP
MT-200 SANKEN 4 Q121.122.221.222
79 067-3300086000QR Diode DIODE BZV86-2V0
STABLSTOR 4 D112.113.212.213
80 067-1104148000R Diode IN4148 33
D214-217.220.221.301-
303.305-309.311
D101.102.106~109.114~11
7.
81 067-2204002000R Zener Diode IN4002 4 D110.111.210.211
82 067-3379479000QR Zener Diode DIODE BZX79C 4V7
ZENER 2 D103.203
83 067-3307912000QR Zener Diode DIODE BZX79C 12V
ZENER 5 D104.105.204.205.310
84 067-3379629000QR Inductor DIODE BZX79C 6V2
ZENER 5 D118.119.218.219.304
85 080-0315000010QR IC 1.5UH 2 L301.302
86 017-4570000000QR Socket OPA134PA DIP08 BB 2 IC101.201
87 051-1004114034QR Tie Wrap 4W T5857-AABE 1 J401
88 071-2480000000QR Resistor YJ-330 2
89 001-3303205010R Resistor 33K 1/4W F 1 R301
90 001-2002205010QR Cap 2K 1/4W 1% 4 R133.134.233.234
91 836-4700012505QR Cap 47P 10% 125V
POLYSTYRENE 2 C401.402