Audiolab 8000M User manual

User Instructions
audiolab
Audiolab
IAG House,
Sovereign Court,
Ermine Business Park,
Huntingdon PE29 6XU
Tel: [phone]
Fax: [phone]
8000P
8000M
8000Q

8: Warranty
Audiolab limited warranty
Audiolab Ltd. warrants this product, subject to the terms and
conditions below, to be free from defects in materials and
workmanship. During the warranty period Audiolab will repair or
replace (at Audiolab's option) this product, or any defective part in
this product, if it is found to be defective due to faulty materials,
workmanship or function. The warranty period may vary from
countrytocountry.
The warranty starts on the date of purchase (or the date of delivery
ifthisislater).
You must provide proof of purchase / delivery before work can be
carried out. Without this proof, any work carried out will be
chargeabletoyou.
All work will be carried out by Audiolab or its authorised agents or
distributors. Any unauthorised repair or modification will void this
warranty.
If any part is no longer available it will replaced with a functional
replacementpart.
AnypartsthatarereplacedwillbecomethepropertyofAudiolab.
Any repair or replacement under this warranty will not extend the
periodofwarranty.
Thiswarranty is valid only in thecountry of purchase, applies only to
thefirst purchaser and is not transferable.
Products on which the serial number has been removed,
alteredorotherwisemadeillegible.
Normalwearandtearandcosmeticdamage.
Transportationorinstallationoftheproduct.
Accidental damage, faults caused by commercial use, acts of
God, incorrect installation, connection or packaging, misuse,
neglect or careless operation or handling of the product which
isnotinaccordancewithAudiolab'suserinstructions.
Equipment that has been operated in conjunction with
unsuitable,inappropriateorfaultyapparatus.
Repairs or alterations carried out by parties other than
Audiolaboritsauthorisedagentsordistributors.
ProductsnotpurchasedfromanAudiolabauthoriseddealer.
Productsthatwerenotnewatthetimeoforiginalpurchase.
Productssold'asis','asseen'or'withallfaults'.
Repairs or replacements as provided under this warranty are the
exclusive remedy of the consumer. Audiolab shall not be liable for
any incidental or consequential damages for breach of any express
or implied warranty in this product. Except to the extent prohibited
by law, this warranty is exclusive and in lieu of all other warranties
whatsoever, both express and implied, including, but not limited
to, the warranty of merchantability and fitness for a practical
purpose.
This warranty provides benefits that are additional to and do not
affectyourstatutoryrightsasaconsumer.
Some countries and US states do not allow the exclusion or
limitation of incidental or consequential damages or implied
warranties so the exclusions in the paragraph above may not
apply to you. This warranty gives you specific legal rights, and you
may have other statutory rights, which vary from state to state or
countrytocountry.
To obtain warranty service contact the Audiolab authorised dealer
from which you purchased this product. Do not despatch goods
without the prior agreement of the dealer, Audiolab or their
authoriseddistributors.
If asked to return products for inspection and/or repair, pack
carefully, preferably in the original cartons or packaging affording
an equal degree of protection, and return prepaid. If unsuitable
packaging is used, Audiolab may make a charge for the supply of
newpackaging.
Insurance is recommended as goods are returned at owner's risk.
Audiolab or their authorised distributors cannot be held liable for
lossordamageintransit.
Packing, insurance and freight on the return journey will be paid by
Audiolab or their authorised agents or distributor if corrective work
provestobenecessary.
Terms and conditions:
The following are not covered:
How to claim:
!
!
!
!
!
!
!
!
!

Mains supply and safety
Important notice to UK users
Mains Supply:
8000Q: 220-240V: 100-120V
8000M: 220-240V: 100-120V
8000P: 220-240V: 4 100-120V
Power Cord:
The mains voltage of Audiolab units is shown on the rear
panel. If this does not match the voltage in your area, consult your dealer.
The mains supply fuse is on the rear panel. If it has broken, check for any
obvious cause before replacing the fuse with one of the correct rating and
type.ThefusesforallareasaretypeT(timelag)AL20mm.
Thefusevaluesare:
1.0A : 1.6A
3.15A : 5.0A
.0A : 5.0A
The fuse is located in a slide-in
carrier which also contains a spare
fuse. The carrier can only be pulled
out after the IEC power cord is
unplugged. When the carrier is
opened the first fuse is the spare.
Remove and safely dispose of the
blownfusebeforereplacingit.
Class II construction double insulated. These products must not
beconnectedtoearth.
An AC power cord is normally supplied with a mains plug
suitable for your area. If you have any doubts, consult your dealer about
obtainingasuitablepowercord.
The appliance cord is terminated with a UK approved mains plug fitted
with a 5A fuse. If the fuse needs to be replaced, an ASTA or BSI approved
BS1362 fuse rated at 5A must be used. If you need to change the mains
plug, remove the fuse and dispose of this plug safely immediately after
cuttingitfromthecord.
Connecting a Mains Plug
Thewiresinthemainsleadarecolouredinaccordancewiththecode:
Blue:NEUTRAL; Brown:LIVE:
As these colours maynot correspondto the coloured markingsidenti ying
theterminalsinyourplug,proceedas ollows:
TheBLUEwiremustbe connected
to the terminal marked with the
letter N or coloured BLUE or
BLACK.The BROWNwiremustbe
connectedtotheterminalmarked
with the letter L or coloured
BROWNorRED.
5A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
Fuse Carrier
IEC Mains Connector
4 ead these instructions.
Keep these instructions. In the event that you pass the product to a third
partythisinstructionmanualshouldbeprovidedalongwiththeproduct.
Heedallwarnings.
Followallinstructions.
Donotusethisapparatusnearwater.
Cleanonlywithdrycloth.
Donotblockanyventilationopenings.
Installinaccordancewiththemanufacturer'sinstructions.
Do not install near any heat sources such as radiators, heat registers,
stoves,orotherapparatus(includingamplifiers)thatproduceheat.
Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
theobsoleteoutlet.
Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Useonlyattachments/accessoriesspecifiedbythemanufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatuscombinationtoavoidinjuryfromtip-over.
Unplug this apparatus during lightning storms or when unused for long
periodsoftime.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture,doesnotoperatenormally,orhasbeendropped.
To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture. The product must not be exposed to dripping
and splashing and no object filled with liquids such as a vase of flowers
shouldbeplacedontheproduct.
No naked flame sources such as candles should be placed on the
product.
Changes or modifications not expressly approved by the
manufacturercouldvoidtheuser'sauthoritytooperatethisdevice.
: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio or television reception, which can be
determined by tuning the equipment off and on, the user is encouraged to
trytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
Re-orientate or re-locate the receiving antenna. Increase the separation
between the equipment and the receiver. Connect the equipment into an
outletonacircuitdifferentfromthattowhichthereceiverisconnected.
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
The batteries supplied with the 8000Q handset should
be treated with care and not punctured or damaged. Used batteries
should be disposed of in full conformity with recycling regulations in your
area.NEVERdisposeofbatteriesinafireorinthegeneralrubbish.
Warning:
Caution:
8000Q
Important Note:
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ADVERTISSEMENT : RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
This symbol indicates that there are important
operating and maintenance instructions in the
literatureaccompanyingthisunit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
withinthisunit.
1: Statutory & Safety Information
8000Q Pre-amplifier 8000P Power Amplifier
Inputs: Gain and Sensitivity
Signal To Noise Ratio
Frequency Response
Total Harmonic Distortion & Noise
Channel Balance
Channel Separation
Pre-amp Output
Headphone Output
Record Output
Muting
Operating Temperature Range
Power Requirements
Dimensions
Weight
Rated Output Power
Input
Load
Gain
Signal To Noise Ratio
Frequency Response
Total Harmonic Distortion & Noise
Channel Balance
Polarity (Phase)
Muting
Operating Temperature Range
Power Requirements
Dimensions
Weight
CD, TUNER, AUX,VIDEO, TAPE1,TAPE2: IMPEDANCE: 20k
GAIN: Adjustable by 3dB steps 0 -15dB., corresponding to
SENSITIVITY(nom.):100,140mV,200mV,283mV,400mV,562mV
HEADPHONES: Gain adjustable 18dB - 33dB in 3dB steps
(IHF,rel.0.5Voutput)
Anyinput,anygainsetting:97dB
Headphones:80dB
10Hz-20kHz±0.2dB: 1Hz-75kHz-3dB.
Lessthan0.007%ref7.7Vrms,20Hz-20kHz
Within1dB
Betterthan100dB@1kHzanyinput,anysetting
Max.Output>7.7VRMS(20dBm); Outputimpedance75
>7.7Vrms;100 (forheadphones8 -2k impedance)
VIDEOOUT,TAPE1OUT, TAPE2OUT:Gain0dB(x1);100
Attenuation>63dB, controlledautomatically
10-35°C
(DependingonRegion)
50-60Hz 100V, 110-120V, and 220-240V models available
MaximumPowerConsumption: 15 VA
(WXHXD)
445x74x335mm-includingfeet,terminalsandcontrols
445x64x302mm-excludingfeet,terminalsandcontrols
Net:6kg Shipping:7.3kg
100W(20dBW)/Channelinto8 bothchannelsdriven
1Vrmsfor100Winto8
InputImpedance:50k
ConnectedinparallelwithINPUT
29.0dBat1kHz
(IHF,rel.0.dBW)
Betterthan95dB
20Hz-20kHz±0.3dB
0.1Hz-75kHz-3dB.
Lessthan0.05%
Within1dB
Non-Inverting
Mutingcontrolledautomatically
10-35°C
(DependingonRegion)
50-60 Hz 100V, 110-120V, and 220-240V models available
MaximumPowerConsumption: 500 VA
(WXHXD)
445x74x337mm-includingfeet,terminalsandcontrols
445x64x302mm-excludingfeet,terminalsandcontrols
Net:8.7kg Shipping:10kg
7: Specifications
8000M Power Amplifier
Rated Output Power
Input Sensitivity
Load
Gain
Signal To Noise Ratio
Frequency Response
Total Harmonic Distortion & Noise
Polarity (Phase)
Muting
Operating Temperature Range
Power Requirements
Dimensions
Weight
125W(21dBW)/Channelinto8 , 20Hz-20kHz
1.12Vrmsfor120Winto8
InputImpedance:50k
ConnectedinparallelwithINPUT
29.0dBat1kHz
(IHF,rel.0.dBW)
Betterthan96dB
20Hz-20kHz±0.3dB
0.1Hz-75kHz-3dB.
Lessthan0.05%
Non-Inverting
Mutingcontrolledautomatically
10-35°C
(DependingonRegion)
50-60Hz 100V, 110-120V, and 220-240V models available
MaximumPowerConsumption: 300 VA
(WXHXD)
445x74x337mm-includingfeet,terminalsandcontrols
445x64x302mm-excludingfeet,terminalsandcontrols
Net:8.2kg Shipping:9.6kg
Audiolab reserves the right to alter design and specification without notice.
Specificationmayvaryfordifferentcountries.
AudiolabisamemberoftheInternationalAudioGroup.

Volume
Press to raise or lower the volume. The
VOLUMEcontrolonthefrontpanelturns.
Unpacking
Inserting Batteries in the Handset
Controls and Functions
Unpacktheproductfully.Thecartonshouldcontain
TheAudiolab8000Q
OneIECpowercordsuitableforyourarea
OneRemoteHandsetwithtwoAAbatteries
Thisinstructionmanual
Reportanydamageorshortagetoyourdealerassoonaspossible.
Retain the packing if possible. If you dispose of the packing, do so
withregardtoanyrecyclingregulationsinyourarea.
Thebatterycompartmentisontherearofthehandset.Unwrapthe
batteries, open the compartment cover and insert the batteries.
Follow polarity indications in the battery compartment. Replace
batteriesinpairs.Usenewbatteriesofthesametypeandrating.
Whenpowerisswitchedonthe8000Qismutedfor3seconds.
Turn to select the listening source. The 8000Q mutes briefly when a
newinputisselected.
This enables you to operate the volume control over a wide area
while minimisingnoise.Forinitialinstallations,setgainto9dB.
REDUCEGain: highsensitivityloudspeakers,lowlevellistening.
INCREASEGain: lowsensitivityloudspeakers,lowoutputsources.
Whenchanginggainthe8000Qwillbrieflymute.
AlteringthegainwillnotaffecttheRecordOutputs.
Adjusts playing volume. Always turn the volume up gradually.
Turn thevolumedownbefore changing inputs.
Turn to select source to record to Tape 1, Tape 2 or Video. You can
recordtoanyCD, tape or otherrecorderwithanalogue inputs.
Record selector and input selector operate independently. It is
possibletorecordfromanysourcewhilstlisteningtoanother.
(availableontheRemoteHandset)
Toggles the pre-amp output On/Off. Recordingisunaffected.
Socket for connection of headphones. Unplug headphones when
notinuse.Connectingheadphonesmutesthe8000Q.
(
(
(
(
Power Switch
Input Selector
Gain Switch
Volume Control
Record Selector
Mute
Headphone Socket
(
(
2a: Introduction- 8000Q
RECORD
SELECTOR
INPUT
SELECTOR
HEADPHONE
SOCKET
POWER
SWITCH
POWER LED
RED=Power On
MUTE LED
RED=Mute On
Input
Press to select listening source. The INPUT
selectoronthefrontpanelturns.
If you wish to record, the record input must be
selectedmanually.
Mute
Toggles mute On/off.
Remote Handset
Buttonsshowninwhitecontrolthe8000Q.
Buttons shown in grey operate Audiolab CD
playersandhavenoeffectonthe8000Q.
As the handset uses RC5 coding it will operate
manyCDplayers.Checkwithyourdealer.
Switching On
Make sure all the signal and loudspeaker connections to and from
theamparesecureandcorrectlymade.
Plug the power cords into the pre-amplifier and the power
amplifier/sandthenintothewallsocket.
Switch on at the mains and then switch on the pre-amlifier
followedbythepoweramplifier/s.
The power indicators on all the units will light showing the system
isoperational.
The 8000Q pre-amplifier may be operated via the front panel or
theremotehandset.
When you have finished using the equipment switch off all the
power amplifiers. Some enthusiasts prefer to leave the pre-
amplifier permanently switched on. If you do this, ensure that the
pre-amplifier is set to mute with the volume control at minimum.
It is essential that the loudspeaker connections are secure and with
thepositiveandnegativeterminalscorrectlyconnected.
This becomes especially important in bi-wired and bi-amplified
systems where the effects of one or more incorrectly connected (out
of phase) loudspeakers may severely impair the sound and yet be
difficulttodetect.
If the sound appears muddled and lacking clarity this may be
because one or more speaker connections are not correctly made.
Always check loudspeaker connections carefully when you have
madeanyalterationtoyoursystem.
Connections should be checked periodically. If necessary the plugs
should cleaned with a proprietary cleaner or, in the case of
loudspeakerconnections,freshlyre-made.
Phase
Maintaining Connections
800Q
VOLUME
CONTROL
REMOTE
CONTROL SENSOR
GAIN
SWITCH
Care & Cleaning
Servicing
While cleaning is in progress the AC power
cord must be unplugged from the AC
powersupplysocket.
Grease or dirt on the equipment may be
removed with a soft, lint-free cloth slightly
moistened with a mild solution of warm
water and detergent or washing-up liquid.
Donotuseanyothersolutionsorsolvents.
If you have any queries regarding the use
of Audiolab equipment, consult your
dealer.
Servicing of Audiolab products should only
be carried out by authorised service
agents. If service is required the
equipment should be returned, securely
packaged, preferably using original
packaging,to your dealer.
In the UK equipment may be returned to
the IAG Service Centre. In the USA
equipment may be returned to the Service
addressshownonthispage.
Always telephone before returning any
equipment.
A note should be enclosed giving your
name, address, telephone number, and a
briefdescriptionofthereasonforreturn.
Ifyou require Service outside the Warranty
period, do not hesitate to contact your
dealer.
IAG Service Centre
Unit 4
St Margaret’s Way
Stukeley Meadows Industrial Estate
Huntingdon
Cambs
PE29 6EB
England
452561
13403
Service Address - UK
Service Address - USA
Tel:[phone]
Fax: [phone]
IAG America, Inc.
15 Walpole Park South
Walpole
MA 02081
USA
Tel: [phone]
Fax [phone]
6: Service5: Operation
Bi-Amplified connection- 8000Q with four 8000M power amplifiers
LEFTRIGHT

3a: Connections- 8000Q
3b: Connections- 8000P & 8000M
8000Q Connections
Running In the 8000Q
CD, TUNER, AUX, VIDEO IN, TAPE 1 IN, TAPE 2 IN
VIDEO OUT, TAPE 1 OUT, TAPE 2 OUT
PRE-AMP OUT 1 & 2
GROUND
Thesixinputsmaybeusedforconnectinganylinelevelsource.
Threesets of record outputs for connection of up to threestereo
audio recorders, e.g. tape recorder, CD recorder, audio
recordinginputofVCR,DVD, MP3, MiniDisc recorder,etc.
Low impedance (100 ohm) pre-amplifier outputs for driving
external power amplifiers, sub-woofers or signal processors.
Long cables may be used if required. Pre-amp outputs are
switched off when integrated mode is selected or whenever
amplifierismuted.
Use only if phono pre-amplifier and turntable are used and
bothareClassIIdoubleinsulated(noearthconnection).Inthis
casetheground terminal can be connected to the metalwork of
these units to eliminate residual hum. The ground terminal
must not be used as a safety earth. If in doubt consult your
dealer.
Before first use, run the 8000Q for a few hours set either
to mute or with the volume control turned to minimum.
Thisenablesthecomponentsto‘burnin’.
(
PRE-
AMPLIFIER
OUTPUTS
VCR
CDR,ETC
MAINS
INPUT
FUSE
HOLDER
TAPE 1TAPE 2
AUX CD, DVD
Connecting the 8000Q to the 8000P - Standard Speaker Connection
Connecting the 8000Q to the 8000P - Bi-Wired Speaker Connection
MAINS
INPUT
FUSE
HOLDER
POWER
AMPLIFIER
INPUT
OUTPUT
TO 2ND
AMPLIFIER
LOUDSPEAKER
TERMINALS
POWER
AMPLIFIER
INPUT
OUTPUT
TO 2ND
AMPLIFIER
LOUDSPEAKER
TERMINALS
RIGHT CHANNEL
LOUDSPEAKER
TERMINALS
LEFT CHANNEL
MAINS
INPUT
FUSE
HOLDER
8000M
8000P
Input
Load
Loudspeaker Terminals - 8000P
Loudspeaker Terminals - 8000M
Good Practice
Running In
For connecting a pre-amplifier or other line level source. Do not
connectdirectlytoaCDplayer or other source unless the source has
itsownfullyadjustablevolumecontrol.
Connectedin parallel with the input. Use to connecta second power
amplifier, either to bi-amplify or to run remote loudspeakers.
Each channel has two sets of loudspeaker terminals connected in
parallel.Thesecondpairistofacilitatebi-wiring,etc.
Therearetwosetsofloudspeakerterminalsconnectedinparallel.
Usegoodquality screened interconnects for signal connections
When running long connections between pre-amplifier and
power amplifier, ensure the pre-amplifier has a low output
impedance(<600 anduselowcapacitancecables.
Neverrunlongsignalcablescloseorparalleltomainscables.
Loudspeaker cables should be low resistance cables designed
foraudiouse-notgeneralpurpose‘bell’or‘zip’wire.
Before first use, run power amplifiers for a few hours with the
source equipment set to mute or the volume control turned to
minimum.This enablesthecomponentsto‘burnin’.
(
(
(
(
(
Multiple Combinations of Audiolab Power Amplifiers
Typically, for bi-amplifying, one would use two 8000P or four 8000M amplifiers.
However, the 8000M and 8000P can be used together in a bi-amplified stereo
configuration where two 8000M amplifiers drive the bass channels and one 8000P drives
thetreblechannels.Eachchannelshouldhavethesameconfigurationofamplifiers.
Both the 8000M and the 8000P can be used in conjunction with the 8000S integrated
amplifierformulti-amping.
Combinations of amplifiers in a multi-channel system should have the same gain and
phase characteristics or imbalance will result. We recommend the use of Audiolab
amplifiers throughout such a system. Current Audiolab amplifiers are gain and phase
compatiblewithpreviousmodels.
Whennotinuse,thepoweramplifiersshouldbeswitchedoff.
Switch power off when making connections
Switch power off when making connections

Connecting Loudspeakers
Switchpoweroffwhenconnectingloudspeakers.
Usegoodqualitylowresistanceloudspeakercable.
Connect the Positive RED (+) terminal of the amplifier to the Positive (+) RED
terminaloftheloudspeaker. Connect the Negative (-) BLACK terminals similarly.
Tighten the loudspeaker terminals securely by hand. Make there are no loose
strandsofwirewhichcouldcauseshorts.
When bi-wiring loudspeakers, make sure you remove the straps connecting the HF
andLFterminalpairs.
Connecting
Cables
RED
BLACK
Speaker
Cables
7mm
20mm
4: Connecting Loudspeakers
Unpacking Power Switch
Unpacktheproductfully. Eachcartonshouldcontain
TheappropriateAudiolabPowerAmplifer
OneIECpowercordsuitableforyourarea
Thisinstructionmanual
Reportanydamageorshortagetoyourdealerassoonaspossible.
Retain the packing if possible. If you dispose of the packing, do so
withregardtoanyrecyclingregulationsinyourarea.
When any Audiolab power amplifier is switched on, the output
remains muted for 8 seconds. After 8 seconds you will hear the
safetyrelayswitchonandthesystemwillnowbeoperational.
Whentheamplifierispoweredtheredpowerindicatorwilllight.
(
(
(
2b: Introduction- 8000P & 8000M
POWER LED RED=Power On POWER SWITCH
8000P
RIGHT LEFT
Pre-Amp Right Output
Pre-Amp Left Output
RIGHT LEFT
Pre-Amp Right Output
Pre-Amp Left Output
8000M - Standard Loudspeaker Connection
If you are stacking the 8000M, by convention the Left Channel is the upper connection
8000M - Bi-Wired Loudspeaker Connection
Bi-wiring offers improved sound quality because high and low frequency signals are carried individually to the loudspeaker drive units.
8000P - Bi-Amplified Loudspeaker Connection
The principle of Bi-wiring can be extended by using a dedicated power amplifier for each loudspeaker drive unit
Standard and Bi-Wired loudspeaker connections using the 8000P are shown in Section 3a.
Switch power off when making connections
Pre-Amp
Output
8000M
POWER LED RED=Power On POWER SWITCH
Power Amplifier Protection Circuits
Short Circuit Protection:
DC Offset Protection:
Thermal Protection:
If the output terminals are connected together or there
is a short caused by a faulty speaker or connecting lead, the amplifier will mute and
un-muteuntilthefaultconditionisremoved.
If there is an internal or external fault which may cause DC
voltage to be presented to the loudspeaker, the amplifier will mute and stay muted
untilthefaultisremoved.
If the amplifier is driven excessively for long periods, or the
output devices are pushed beyond their safe operating area, the amplifier will
switchoffandthenswitchbackonagainwhenithascooleddown.
Inallcases,iftheamplifierdoesnotrespondtoremedialaction,consultyourdealer.