Audioplex LUMA-VRS-1 User manual

Remote Controlled Component Video Switcher
SPECIFICATIONS:
INSTALLATION
OPERATION
Power: 12 vdc 500ma power supply included
Connectors: RCA audio and video / RS-232 computer interface
1/8" mono jack for emitter cable (included)
1/8” stereo jack for 56KHz infrared sensor (included)
Dimensions: 9.5”W x 2.5”H x 4.875”D
The Luma Series of remote controlled video switchers are designed to offer convenient A/B video switching.
Multiple switchers can be used, allowing for up to six monitor locations controlled by a ProScan/RCA remote.
With power off, make connections to your Luma Series switcher following the wiring diagram on the back of this
sheet. Once all the connections have been made, plug in the power supply to start up the unit. 1/8" jacks are
provided for emitter in ( for use with remote relay systems) and for the included infrared sensor (for remote
control in the same room).
The rotary switch in the front of the switcher sets the ID number for the particular Luma Video Switcher. The
front rocker switch changes between Toggle and Discreet IR codes.
TOGGLE MODE: In Toggle mode, 6 individual Luma's may be controlled via the 6 source selector button
functions on ProScan/RCA remotes. The source buttons are: Video 1, Video 2, CD, Tape, TV, Tuner. If there is a
conflict with any other RCA equipment in the system, then the rotary switch can be moved to relieve the conflict.
In the Toggle mode, each press of a button will cause the Luma to change from "A" to "B" in a circular fashion.
Available rotary switch positions are: 1, 2, 3, 4, 5, and 6.
DISCRETE MODE: In Discrete Mode, only 3 individual Luma's may be controlled as the "A" and "B" input
sources are selected via an individual remote control code. Available rotary switch positions are: 1, 2, and 3.
LUMA-VRS-1
TECHNOLOGY
INSTALLATION MANUAL
2005 - 11/14/05
ProScan remote control codes
Toggle Mode
Rotary Switch Position 1 2 3 4 5 6
Remote Button Vid 1 Vid 2 CD Tape TV Tuner
Discrete Mode
Rotary Switch Position 1 2 3 Video Input
Remote Button Vid 1 CD TV A
Remote Button Vid 2 Tape Tuner B

WIRING DIAGRAM
WARRANTY
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440 MELVIN VILLAGE, N.H. 03850 1-800-257-2077 FAX: [phone]
2005 - 11/14/05
AUDIO +12V
MADE IN USA
LUMA-V-RS-1
RGB
R
G
B
RGB
A IN OUT B IN
R
L
A VIDEO IN
RS-232
VIDEO
OUT
B VIDEO IN
dVD 2.53
VIDEO SOURCE A
EMITTER CABLE IN
56KHz INFRARED SENSOR
dVD 2.53
VIDEO SOURCE B
RS232
Messages from Video Switchers:
On models equipped with RS232, control is possible
using the following communication parameters: COM
Port 8,N,I 2400 baud, no flow control, 8 bits, No Parity,
1 Stop Bit.
Send text under ASCII text column all CAPS. Video
Switch will respond appropriately if correct rotary
switch position and rocker switch position is selected on
When ever SW receives an RS232 command, it will respond with a message. If the SW changes position it will respond as in
the two following examples:
Audioplex Switch 2 Pos A
Audioplex Switch 3 Pos B
If a redundant command is sent, i.e. "change to position (A) when the switch is already in that position, or the rotary switch
on the front of the unit is set to a different SW ID number, then the Luma will send an error message, i.e.
Wrong SW command, From SW#, Pos?
In all cases, when the Luma responds it will tell you what SW ID is currently set to be, and whether it is in the "A" or "B"
position.
ASCI text to send Rot SW Pos 1 Rot SW Pos 2 Rot SW Pos 3
AUDIOPLEXRSWA11 A
AUDIOPLEXRSWA10 B
AUDIOPLEXRSWA21 A
AUDIOPLEXRSWA20 B
AUDIOPLEXRSWA31 A
AUDIOPLEXRSWA30 B
Your AUDIOPLEX TECHNOLOGY Luma Series Video Switcher is covered by a Lifetime warranty against defects in
workmanship and materials. Any defects will be remedied without charge for labor or parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty. AUDIOPLEX
TECHNOLOGY is not responsible for defective operation caused by abuse or by modification or service by an unauthorized person or
agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary servicing
must be done by AUDIOPLEX TECHNOLOGY. The products must be returned expences prepaid, with written authorization from the
company. The unit must be shipped with the proof of purchase and in the original carton and packing material to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.

Remote Controlled S Video Switcher
SPECIFICATIONS:
INSTALLATION
OPERATION
Power: 12 vdc 500ma power supply included
Connectors: RCA audio and S-video
1/8" mono jack for emitter cable (included)
1/8” stereo jack for 56KHz infrared sensor (included)
Dimensions: 9.5”W x 2.50”H x 4.875”D
The Luma Series of remote controlled video switchers are designed to offer convenient A/B video switching.
Multiple switchers can be used, allowing for up to six monitor locations controlled by a ProScan/RCA remote.
With power off, make connections to your Luma Series switcher following the wiring diagram on the back of this
sheet. Once all the connections have been made, plug in the power supply to start up the unit. 1/8" jacks are
provided for emitter in (for remote relay systems) and for the included 56KHz infrared sensor (for remote control
in the same room).
The rotary switch in the front of the switcher sets the ID number for the particular Luma Video Switcher. The
front rocker switch changes between Toggle and Discreet IR codes.
TOGGLE MODE: In Toggle mode, 6 individual Luma's may be controlled via the 6 source selector button
functions on ProScan/RCA remotes. The source buttons are: Video 1, Video 2, CD, Tape, TV, Tuner. If there is a
conflict with any other RCA equipment in the system, then the rotary switch can be moved to relieve the conflict.
In the Toggle mode, each press of a button will cause the Luma to change from "A" to "B" in a circular fashion.
Available rotary switch positions are: 1, 2, 3, 4, 5, and 6.
DISCRETE MODE: In Discrete Mode, only 3 individual Luma's may be controlled as the "A" and "B" input
sources are selected via an individual remote control code. Available rotary switch positions are: 1, 2, and 3.
LUMA-VR-1
TECHNOLOGY
INSTALLATION MANUAL
2005 - 11/14/05
ProScan remote control codes
Toggle Mode
Rotary Switch Position 1 2 3 4 5 6
Remote Button Vid 1 Vid 2 CD Tape TV Tuner
Discrete Mode
Rotary Switch Position 1 2 3 Video Input
Remote Button Vid 1 CD TV A
Remote Button Vid 2 Tape Tuner B

WIRING DIAGRAM
WARRANTY
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440 MELVIN VILLAGE, N.H. 03850 1-800-257-2077 FAX: [phone]
2005 - 11/14/05
dVD 2.53
VIDEO SOURCE A
EMITTER CABLE IN
56KHz INFRARED SENSOR
dVD 2.53
VIDEO SOURCE B
Your AUDIOPLEX TECHNOLOGY Luma Series Video Switcher is covered by a Lifetime warranty against
defects in workmanship and materials. Any defects will be remedied without charge for labor or parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty.
AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by modification or service by
an unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary
servicing must be done by AUDIOPLEX TECHNOLOGY. The products must be returned expences prepaid, with written
authorization from the company. The unit must be shipped with the proof of purchase and in the original carton and packing
material to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
+12V
A IN OUT B IN
MADE IN USA LUMA-V-R-1
A IN OUT B IN
VIDEO
AUDIO
R
L