Prismatibro Prisma Button 800 User manual

MANUAL
INSTALLATION
800
ELBOW SWITCH
ACTIVATION PANEL

• Remove the top lid Aand bottom lid Iin accordance with image on the
next page, and pull out the push front Ffrom the outer prole E
• Set the dip-switches as desired, as described on the last page
• Adjust the length of the wire from the wall box to the connection terminal
with a good margin.
• Thread the cabling through the cable outlet Con the outer prole E
• Install the cabling according to diagram J
• Slide the push front Fdown the outer prole Eso they are edge to edge
• Mount outer prole Ewith screws at screw holes Band I
• Mount the top lid Aand bottom lid Iso it “clicks”
• Turn on, wait a few seconds until the unit starts.
MOUNTING AND INSTALLATION
• Cable outlet 599 mm alternative 680 mm from the the lower edge, with the
bottom lid mounted
• Recommended height: about 120 mm from the oor.
• Cable: H05V-U (EK)
H05V-K (RK) is okay to use wire end ferrules
Minimum cross section area according to cable standard
HD21 is 0.5 mm2 for EK and RK
• When mounted outdoors: Drill a drain hole in marked depression in the bottom lid.
PREPARATION
TECHNICAL SPECS
Dimensions 799 x 95 x 25 mm
Power supply 18-30 VDC
Connection cable 2 wires for power supply
2 wires for signaling door auto-
matics
Power consumption Standby ≈ 30mA
Activated ≈ Max 47mA
Relay, max rated current Maximum per pole 2A
Material Outer prole and Push front Aluminum
Material Lids Polyamide

Circuit board
Top lid
Outer prole
Bottom lid
Connection diagram
Push front (front)
Push front (back with electronics)
Cable outlet
Screw holes
A
E
I
J
Relay 1 Relay 2
Pole 1
Relay 2
Pole 2
24 V
0 V
Screw hole
B
F
G
H
D
C
1
3
2
4
Dismantling top and bottom lid

1000
800
120
600
119
657
143
286
1169
120 799
Floor/ Ground
599
489
IDENTICAL FUNCTIONS All models oer the same functions
PRISMA BUTTON 800 AS ELBOW SWITCH
PRISMA BUTTON 1200
AS ACTIVATION PANEL
ALTERNATIVE MOUNTING

1000
800
120
600
119
657
143
286
1169
120 799
Floor/ Ground
599
489
PRISMA BUTTON 300 AS ELBOW SWITCH
PRISMA BUTTON 800 AS ACTIVATION PANEL

DIP-SWITCH
EXTENDED PUSH
LIMITED RELAY CONNECTING TIME
KICK FUNCTION
OFF
• There are 8 dip-switches
on the circuit board.
• When delievered - All dip
switches are set in OFF mode.
• You can activate several
dip-switches depending
on the requested functions.
NOTE
Dip-switch “Extended push” and “Nurse Bed” cannot be activated at the same time.
Press and hold the push front for 1.5 seconds to activate.
Dip-switch 1: ON
NOTE If dip-switch 8 is set ON this function will be deactivated
You can choose the option of a relay connecting time for
max 1 second.
It will only recieve one signal no matter the pressure time on
the push front.
Dip-switch 4: ON
Requires stronger push/kick.
Dip-switch 3: On
Press and hold the push front for 3 seconds to activate.
Dip-switch 2: ON
NOTE If dip-switch 8 is set ON this function will be deactivated
Press and hold the push front for 6 seconds to activate.
Dip-switch 1 and 2: ON
NOTE If dip-switch 8 is set ON this function will be deactivated.
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON

NOTIFICATION SOUND
DIP-SWITCH 6
RELAY 2
NURSE BED FUNCTION 1
NURSE BED FUNCTION 2
When you press the push front there is a notication sound.
Dip-switch 5: ON
Always set on OFF mode. Is not used.
Available spot for future functionalities
Switch to OFF mode.
Dip-switch 7: ON
Control the pair doors in dierent ways, depending the
pressure on the push front.
Direct push: activate relay 1,“Door 1”
Extended push 1.5 seconds activate relay 2,“Door 2”.
Dip-switch 8: ON
Control pair doors in dierent ways depending the
pressure on the push front.
Direct push: activate relay, 1 “Door 1”
Extended push 1.5 seconds aktivate
relay 1+2,“Door 1” and “Door 2”.
Dip-switch 1 and 8: ON
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678
ON DIP
12345678

ADDRESS Jarnvagsgatan 19, SE-543 50Tibro
SWITCHBOARD [phone]
WEB prismatibro.se
E-MAIL [email protected]
ACCESSIBILITY FOR EVERYBODY
1200 800 300
© PrismaTibro • XXXXX · 180814