Audiopole MIX-7 User manual

12 CHANNEL MIXER
MIX-7
USER’S MANUAL

POWER SUPPLY
Ensure that the insource voltage (AC outlet) matches the voltage rating of the product. Failure to do so could
result in damage to the product and possibly the user. Unplug the product before electrical storms occur and
when unused for long periods of time to reduce the risk of electric shock or fire.
2
EXTERNAL CONNECTION
Always use proper ready-made insulated mains cabling (power cord). Failure to do so could result in
shock death or fire. If in doubt, seek advice from a registered electrician.
FUSE
To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual. Do
not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected
from the ACD outlet.
PROTECTIVE GROUND
Before turning the unit on, make sure that it is connected to Ground. This is to prevent the risk of electric shock.
Never cut internal or external Ground wires. Like wise, never remove Ground wiring from the Protective Ground
Terminal.
OPERATING SAFETY INSTRUCTIONS
Read these instructions. Follow all instructions. Keep these instructions. Do not discard. Heed all warnings. Only
use attachments accessories specified by the manufacturer.
This symbol indicates that the disposal of this product is submitted to local regulations. Please
contact your local dealer.
DISPOSAL
Important Safety Instr ctions
This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages
within the product enclosure. These are voltages that may be sufficient to constitute the risk of
electric shock or death.
This symbol, wherever used, alerts you to important operating and maintenance instructions.
DO NOT REMOVE ANY COVERS
Within the product are areas where high voltages may present. To reduce the risk of electric shock do not
remove any covers unless the AC mains power cord is removed. Covers should be removed by qualified service
personnel only. No user serviceable parts inside.
POWER CORD AND PLUG
Do not tamper with the power cord or plug. These are designed for your safety. Do not remove Ground
connections! If the plug does not fit your AC outlet seek advice from a qualified electrician. Protect the power
cord and plug from any physical stress to avoid risk o electric shock. Do not place heavy objects on the power
cord. This could cause electric shock or fire?
SERVICING
Refer all servicing to qualified service personnel only. Do not perform any servicing then those instructions
contained within this User’s Manual

3
1. Introduction …………………………………………………………………….….. 4
2. Features ……………………………………………………………………………. 4
3. Controls …………………………………………………….……………………… 4
4. Diagram ……………………………………………………………………………. 7
5. Technical Specifications……………………………………………………...…… 8
6. Warranty ……………………………………………………………………….…… 9
Index

Introd ction
4
Thank you for purchasing AUDIOPOLE MIX-7. The device is a compact mixer designed for multiple
applications, including AV and conference.
1
Feat res
•6 mono inputs including 1 priority IN,
•3 stereo inputs,
•Stereo output,
•Mono output,
•Micro output,
•3 band EQ,
•Individual phantom power,
•Back up power supply 24 V DC.
2
Controls
Front
3
1. CH 1 – CH 11/12
Volume of Mic Line inputs 1 to 6 and stereo inputs 7 8 to 11 12.
2. SIG
LEDs indicating the presence of the signal, the light intensity is proportional to the input level.
3. MIC – OUT, ON/OFF
On ON position, inputs 1 to 6 are assigned to the MIC OUT exclusively with independent level setting.
Attention, the EQ and the priority function do not work on this output.
4. EQ
3 bands EQ only active for MONO, LINE OUT (MASTER) and RECORD OUT outputs. The frequency
ranges are centered respectively on 80 Hz (LOW), 2.5 kHz (MID) and 12 kHz (HIGH).

Controls
Front
5. MONO – OUT
MONO output level setting.
6. L, R INDICATOR
Colored LEDs displaying the output LINE OUT (MASTER) level. The red LEDs (clip) indicate the presence
of saturation; then adjust the levels accordingly.
7. MASTER – OUT
Stereo LINE OUT level setting. When you turn ON OFF the device, the level must be adjusted to zero.
8. SWITCH ON/OFF
ON OFF power switch. The led lights when the power is on.
9. RACK-MOUNTABLE
Holes for 19’’ rack mounting.
3
5
Back
10. AC INPUT
Socket for connection of the mains cable, also contains the fuse compartment. Before any connection check
the mains voltage. When replacing the fuse, use a fuse with the same characteristics.
11. DC POWER 24V
Terminals for back up power supply 24 V DC. In the event of main power failures, the DC power takes over
automatically. When connecting, observe the correct polarity.
12. LINE OUT (MASTER)
Balanced stereo output, XLR.
13. MONO OUT
Unbalanced mono output, 6.35 mm Jack.
14. MIC OUT
Unbalanced, output 6.35 mm Jack, allocated exclusively to inputs 1 to 6 when the switch (3) is turned ON.
15. REC OUT
Unbalanced stereo output, RCA. Intended for recording.

Controls
Back
16. LINE INPUTS
Unbalanced stereo inputs, RCA. Intended for the connection of stereo sources (CD, DVD, MP3, etc.)
17. LINE / +24V / MIC
Selectors of 3 input types :
•Line,
•Electret microphone with +24 V phantom power supply,
•Dynamic microphone.
18. MIC / LINE INPUTS
Balanced unbalanced stereo inputs, combo XLR 6.35 mm Jack.
19. MIC 1 PRIORITY
Adjusts the attenuation level when the priority input is active. The signal of inputs 2 to 11 12 is completely
attenuated when the setting is maximum; attenuation is disabled when the setting is at a minimum.
3
6

Diagram
4
7

8
Technical specifications
5
Microphone inp ts Electronically balanced
Frequency response 20 Hz - 22 kHz (± 3 dBu)
THD < 0,03% @ 1kHz
Gain range 0 dB à -50 dB
Max input level + 18 dBu
Max gain 60 dB CH MIC INPUT → LINE OUT
50 dB CH MIC INPUT → REC OUT
60 dB CH MIC INPUT → MIC OUT
60 dB CH MIC INPUT → MONO OUT
S N ratio > 85 dB
Phantom power + 24 V
Line inp ts Electronically balanced
Frequency response 20 Hz - 22 kHz (± 3 dBu)
THD < 0,03% @ 1 kHz
Sensitivity 0 dBu
Max input level + 18 dBu
Max gain 20 dB CH MIC INPUT → LINE OUT
10 dB CH MIC INPUT → REC OUT
20 dB CH MIC INPUT → MIC OUT
20 dB CH MIC INPUT → MONO OUT
Line inp ts Electronically balanced
Frequency response 20 Hz - 22 kHz (± 3 dBu)
THD < 0,03% @ 1kHz
Sensitivity - 10 dBu
Max input level + 20 dBu
Max gain 20 dB CH → LINE OUT
10 dB CH → REC OUT
14 dB CH → MONO OUT
S N ratio > 105 dB
Mic inputs 1,4 kΩ
Other inputs 10 kΩ or plus
REC OUT 1 kΩ
Other outputs 120 Ω
High ± 15dB @ 12 kHz
Medium ± 12dB @ 2,5 kHz
Low ± 15dB @ 80 Hz
adjacent inputs < -68 dB @ 1kHz (CH1 - CH4)
Input output < -72 dB @ 1kHz (STEREO L R, CH1 - CH 6)
LINE OUT 0 dBu (± 2dB) balanced, XLR
MONO OUT, MIC OUT 0 dBu (± 2dB) unbalanced, 1 4" Jack
Max output level + 20 dBu balanced unbalanced, 1 4" Jack
Noise level < -80 dB @ 20 Hz - 22 kHz (input and output levels at
0 dB, flat EQ, other levels to min.)
Main supply 115~230 V 60 50 Hz
Other supply + 24 V DC
Dimensions L x H x P 483 x 44 x 195 mm
Weight Net 2.9 kg
O tp ts
Power s pply
Inp ts
Mono inp ts (CH1 - CH6)
Stereo inp ts (CH7/8 - C11/12)
Impedances
EQ
Cross talk

9
This device is warranted parts and labor against any manufacturing defects for a period of two years from the
date of purchase by the first user.
Conditions
1. The unit has been installed and implemented by observing the safety instructions in this operating manual.
2. The device was not diverted from its destination, either voluntary or accidental, and suffered no
deterioration or modification other than those described here or explicitly authorized by AUDIOPOLE.
3. All modifications or repairs have been carried out by an authorized service station.
4. The defective product must be returned with the dealer who made the sale or to an authorized service
station with proof of purchase.
5. The device was properly packaged to avoid damage in transport.
6
22, rue Édouard Buffard, Z.A.C. de la Charbonnière, Montévrain - 77771 Marne-la-Vallée Cedex 4 - France
Tél : + 33 (0)1 60 54 32 00 - Fax : + 33 (0) 1 60 54 31 90 - www.audiopole-pa.fr, www.audiopole.fr
Warranty