Audiosystem H Series User manual

designed and engineered by audio system Germany
H-5000.1 D
owner‘s manual

H-5000.1 D
- Clipping-Display and switchable limiter
- Variable Bass-Boost from 0 to 9 dB
- High efficiency up to 90%
- Wide input sensitivity from 0,2 to 6 V
- Stable into 1 Ohm (single mono operation)
- Variable Phase from 0° to 180°
speakr DC offset protection
- 1-Channel High Power Class D amplifier
- Variable Subsonic-Highpass-Filter from 10 to 50 Hz
- Multi-Way-Protection-Circuitry: overheating, overcurrent, short circuit and
- 2x H-5000.1 D linkable up to 10.000 Watt RMS - NO WARRANTY CLAIMS POSSIBLE!
- Wired remote RTC PLUS showing voltage, temperature, protection, clipping
- Quad-MOS-FET PWM power supply, operating voltage from 10 to 16 V
- 2x 50mm² connection terminals each for battery and ground
- Variable Lowpass-Filter from 35 to 250 Hz
features
ATTENTION: Pay attention to advices and instructions of the car manufacturer.
ATTENTION: NO WARRANTY claims for operation in LINK-MODE possible!!!
IMPORTANT: Your proof of purchase is evidence of warranty claim for repair or replacement. Keep your proof of
purchase, manual and original packaging.
IMPORTANT: Before installation your power amplifier, we recommend to read the owner´s manual carefully and
to follow the instructions regarding connection and fitting exactly.
ATTENTION: Use of sound components can impair your ability to hear necessary traffic sounds and may
constitute a hazard while driving your automobile.
Audio SystemGermany accepts no liability for hearing loss, bodily injury or property damage
as a result of use or misuse of our products. We recommend installing the equipment by an authorized service
center or dealer. A professional fitting and connection is the requirement for further warranty and perfect sound.
Congratulation on your purchase of your new H-Series amplifier.

H-5000.1 D
BATTERY
GROUND Ma x.30 c m
Ma x.30 c m Ma x.30 c m
4. Remote connection: Connect the REM IN terminal of the amplifer to the remote output (or antenna output) of the
head unit. Please use a 0.5mm² to 1.5mm² cable.
1. Battery disconnection: First, disconnect the power supply of the vehicle by removing the ground cable of the
battery.
2. Ground connection: Connect the GND (ground) terminals of the amplifier with the car chassis. Keep this cable as
short as possible (not longer than 50cm) and use a suitable cross section (35mm² - 50mm²). Make sure that the
connection point with the chassis os free of paint, dirt and dust.
3. +12 V Power connection: Connect the +12 V terminals of the amplifier via fuses to the battery. Keep in mind, that
the length of the cable from fuseholder to battery must not exceed 30cm in length.For the amplifier to work best,
please use a high quality fuse holder and a suitable cable preferable 35mm² - 50mm². The fuses protect the amplifier
and the vehicle against short circuits. Attention! The amplifier has no internal fuses so external fuses before
amplifiers must also be installed!!
a) Take care of a professional attachement. Pay attention, that no electrical cable, gas tank, hydraulic
breakes or other components get damaged.
b) There has to be enough cooling and air circulation. Avoid the installation in small closed boxes or close
to heatening parts.
c) Protect the amplifier from fluids, wetness, heat and foreign material as well as from other influences.
d) The amplifier is only to be built into vehicles with a 12 V DC power supply.
e) Never install the power supply cable with other original wires of the vehicle (gas cables), fan motors,
brand control moduls etc.
f) Install the signal cable (cinch cable) as well as the speaker cable far away from the power cables to
avoid troubles with the music signal.
g) The cables of your amplifier have to be installed, so that there is no danger of binding, squeezing or
breaking.
Please follow the instructions during the installation of your amplifier:
ATTENTION

H-5000.1 D
H-5000.1 D
PWR
PRT
TEMP
CLIP MINMIN MAX
VOLTAGE / TEMP
1. RCA connection for operation of 1 amplifier
RTC PLUS
H-5000.1 D
PWR
PRT
TEMP
CLIP MINMIN MAX
VOLTAGE / TEMP
The H-5000.1 D amplifiers offers RCA-inputs, which are connected by RCA cinh-cables to the preamplifier
outputs of the headunit.
Using the „Master/Slave“ connection (single RCA) it‘s possible to link a second H-5000.1 D with the
LINK-MODE. For LINK-MODE switch second amplifier to „INPUT SLAVE“, then this amplifier is fully controlled by
the first „Master“ amplifier.
No warranty claims for operation in LINK-MODE possible!
With the aid of the variable subsonicfilter, lowpassfilter, phase-shift-controller, bass boost, limiter and gain-con-
troller you are able to adjust the amplifier on your preferred taste of listening, the circumstances of the vehicle
and to the speakers.
In this regard, Audio System Germany recommends to adjust your amplifier through a
specialized service center, dealer or specialist.
Optional a wired remote controller RTC PLUS can be installed. This controller can adjust the output level
and show you amplifier datas for voltage, temperature, clipping, protect and on state.
RTC PLUS
H-5000.1 D
2. RCA connection for operation of 2 amplifiers in LINK-MODE
NO WARRANTY CLAIMS
POSSIBLE WHEN USING
LINK-MODE!!!

BATTERY
GROUND Ma x.30 c m
Ma x.30 c m Ma x.30 c m
1. Single amplifier operation
BATTERY
GROUND Ma x.30 c m
Ma x.30 c m Ma x.30 c m
Speaker-
impedance
2 ~ 4 Ohm
Speaker-
impedance
2 ~ 4 Ohm
Speaker-
impedance
1 ~ 4 Ohm
Please note that the H-5000.1 D is a
pure mono amplifier. When connecting 2
speakers or a dual voice coil subwoofer, the
speakers (voice coils) are connected in
parallel. It should be noted that each voice
coils or speakers impedance is not below 2
ohms. The total resulting impedance is 1 ohm.
No internal fuse ! An external fuse
- according to the power input -
has to be used for protection of the amplifier
No internal fuse ! An external fuse
- according to the power input -
has to be used for protection of the amplifier

BATTERIE
MASSE Ma x.30 c m
Ma x.30 c m Ma x.30 c m
1. Dual amplifier operation (LINK-MODE)
BATTERIE
MASSE Ma x.30 c m
Ma x.30 c m Ma x.30 c m
Speaker-
impedance
2 ~ 8 Ohm
NO WARRANTY CLAIMS POSSIBLE WHEN USING LINK-MODE!!!
ATTENTION! The connected overall impedance of the speakers must not drop below 2 ohms in LINK-MODE.
Otherwise the amplifier can take damage.
When linking 2x H-5000.1 D the „Master“ amplifier completely controls the „Slave“ amplifier. The positve (+)
terminal of woofer has to be connected to the positive (+) speaker terminal of the „Master“ amplifier. The negative(-)
terminal of woofer is connected to the positive(+) speaker terminal of the „Slave“ amplifier. Both negative(-)
terminals of the amplifiers are connected together. Please use cables with sufficient cross section (10mm²), because
in LINK-MODE the amplifiers produce immense power. Please make sure that the connected speakers are suitable
for this power.
No internal fuse ! An external fuse
- according to the power input -
has to be used for protection of the amplifier
No internal fuse ! An external fuse
- according to the power input -
has to be used for protection of the amplifier
NO WARRANTY CLAIMS
POSSIBLE WHEN USING
LINK-MODE!!!

Trouble Shooting
Occuring an error the protection-LED will light in red. In order to check the problem, first turn down all levels of
the head unit, afterwards turn it off.
This power amplifier is featured with an efficient protection system to prevent any damages like over-heating,
overvoltage, short-circuit and DC at the loudspeaker output.
AMPLIFIER IS NOT
POWERED UP, NO LED IS
LIGHTENING - remote cable professional connected?
- ground connection professional connected?
- +12V powercable professional connected?
- fuses inserted and alright?
- analyze voltage on the amplifier.
- loudspeaker professional connected?
- cinch cable alright and professional connected
- head unit alright?
- amplifier too hot?
- short-circuit at the loudspeaker output?
- short-circuit caused by loudspeaker cable with vehicle chassis (ground)?
- input voltage too high (e.g.faulty generator)?
PROTECTION LED
WHILE AMPLIFIER IS
SOUNDLESS
ILLUMINATES GREEN
WHEN AMPLIFIER IS
PROTECTION LED
POWERED UP
ILLUMINATES RED
ERROR IN AMPLIFIER FUSE - ground professional connected?
Make sure when changing fuses to use the same value.
- loudspeaker impedance alright?
! CAUTION !
LOW-DISTORTED SOUND
SOUND TOO LOW OR
- loudspeaker error?
- loudspeaker cable checked?
- crossover frequencies has been properly set?
- input level control “GAIN” is set to match the head unit?
frequency bandpassfilter...)
(Check head unit, amplilfier, DSP, soundprozessor, equalizer,
- output level control of the head unit alright?
- ground connection professional connected?
- short-circuit caused by loudspeaker cable with vehicle chassis (ground)?
- cinchcable (RCA) and/or loudspeaker cable installed too
close to the power connection cable?
- cinch ground (RCA) of the head unit alright?
HIGH HISS-ENGINE NOISE
IN SPEAKERS
Please contact your specialized dealer if the amplifier is still not working after it has been
checked with the error list!
For warranty adjustement / repairs the original invoice has to be attached!
Opening the power amplifier is leading to a lost of warranty in either case!
AT TEN T ION
(PROTECTION LED
ILLUMINATES RED WHEN
AMPLIFIER IS POWERED UP)
OVERHEATING
After cooling down, the amplifier turns on automatically.
- adequate airflow of the amplifier?
! CAUTION !
- impedance alright?
- loudspeaker error?
CArbon series
by audio system

H-5000.1 D
Power Supply Voltage
Rated Power Output at 14,4 V
-RMS power @ 2 Ohm LINK-MODE
-RMS power @ 1 Ohm mono
-RMS power @ 2 Ohm mono
-RMS power @ 4 Ohm mono
Signal to Noise Ratio
Low-Pass-Filter
Subsonic Filter
Bass Boost
Phase-Shift-Control
Frequency Response
THD at 4 Ohm
Fuse Rating
Input Sensitivity
Dimensions
10 - 16 V
1x 10.000 W
1x 5000 W
1x 3100W
1x 1650W
> 95 dB
35 - 250 Hz @ 24 dB
10 - 50 Hz @ 24 dB
0 - 9 dB @ 45 Hz
0 - 180°
15 - 270 Hz
< 0,048%
external
200 mV ~ 6 V (+/- 5%)
550(W) x 63(H) x 256(L) mm
Audio System Germany
Falltorstraße 6 - 76707 Hambrücken
designed and engineered by audio system Germany
R
since 1988
german sound
specifications