Audiovox Pursuit PRO 2000S User manual

1
Model PRO 2000S
Owner’sManual
3 Button Remote Security System with
Keyless Entry
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due
to battery failure. Reading the sections on " MANUALLY OVERRIDING YOUR SYSTEM " is
necessary to fully understand the procedure required to enable your vehicle in such situa-
tions. In addition, the chart on the last page of this manual has a section for the particular
features and options installed in your vehicle as well as the override method selected. Valet
Switch manual override is pre-selected from the factory, however, the system can be
configured for "Custom Code" operation. Confirm the override mode selected on the last
page of this manual, and familiarize yourself with the selection on it's operation.
FEATURES :
w2ThreeButtonProgrammableRFTransmitters (capableofaccepting4transmitters)
wFour Channel Receiver
wSelectable Manual Override Mode
wRemote Panic in all modes
wProtected Valet
wUser Programmable Manual Override Code
w7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
wIntrusion Alert with Memory
wAudible Arm / Disarm / Defective Zone / Tamper Confirmation
wInstant Siren Activation
wTrue Last Door Arming ( hardwire only )
wDefective Zone By-Pass
wHardwire or Voltage Sense Selectable
wActive or Passive Arming Selectable
wProgrammable Auto Lock On / Off
wProgrammable Auto Unlock On / Off
wProgrammable Door Lock Pulse Duration
wProgrammable Active or Passive Door Locks
wUserProgrammable PermanentChirp Delete
wOn Command RF Chirp Delete from Transmitter Or Selectable Through Software
wAdditional Negative Trigger Input
w6 Tone Multi Tone Siren (And or)
wCar Horn Activation for additional alarm response
wRF Inhibit with ignition on
wParking Light Flasher
wRemote Trunk Release ( Option and must have electronic trunk release )
wRemote Keyless Entry With Optional Access Guard ( must have power door locks )
OPTIONS :
wIlluminatedEntry
wStarter Disable
wMultiple Vehicle Capable
wRemote Starter
wRemote Power Window Roll Up
wRemote Garage Door Interface
wPlug In Electronic Shock Sensor

2
THISPAGE INTENTIONALLYLEFT BLANK

3
NOTE: This unit uses the vehicles horn as a sounding device. In some installa-
tions the optional siren may have been used in place or or in addition to
the vehicle horn as a sounding device. Where siren chirps are referenced
below, the horn beeps may be substituted or in addition to.
ARMINGTHESYSTEM-ACTIVE
1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.
2. Press and release the Lock button on the keychain transmitter.
þRed dash mounted LED begins to flash slowly.
þParking Lights flash one time.
þSiren sounds one chirp.
If the siren sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. Simply close the opened entry point to provide full
protection. If the siren did not sound when arming, then the
chirps have been turned off, and you should refer to the section
titled“ELIMINATINGTHEARM/DISARMCHIRPS”inthismanual.
þDoors Lock
SILENTARMING-ACTIVE
1. Turn off the engine, exit the vehicle and close all doors, hood lid, and trunk lid.
2. Press and hold the Lock button on the keychain transmitter for 2 seconds.
þRed dash mounted LED begins to flash slowly.
þParking Lights flash one time.
þSiren will not sound.
If the siren sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. Simply close the opened entry point to provide full
protection.
þDoors Lock
ARMINGTHESYSTEM - PASSIVE( AUTOMATIC )
1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid and
trunk lid.
þRed dash mounted LED begins to flash rapidly, indicating 30 second
passive arming has begun.
2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming and the 30 second passive arming
cycle will re-start when all doors are closed. At the end of the passive arming
cycle; þRed dash mounted LED begins to flash slowly.
þParking Lights flash one time.
þSiren sounds one chirp

4
If the siren did not sound when arming, then the chirps have
been turned off, and you should refer to the section titled
“ELIMINATING THE ARM / DISARM CHIRPS” in this manual.
þDoors Lock
Door locking during passive arming is a selectable feature.
The alarm can be programmed to allow the doors to lock only
when arming using the keychain transmitter, and they will not
automatically lock during passive arming.
PROTECTIONWHILE THESYSTEMISARMED
þOpening any protected door, hood, or trunk lid will cause the alarm to
immediately sound. The alarm will continue to sound for 30 seconds, then
stop and continue to monitor all protected entry points. If the thief left a door
opened, the alarm will sound for six 30 second cycles, remain armed, and
ignore that triggered zone.
þWhenever the system is armed, the red dash mounted LED indicator
will slowly flash. This serves as a visual deterrent to the potential thief. The
LED is a very low current bulb, and will not cause the vehicle’s battery to
drain, even when left unattended for extended periods.
þWhenever the system is triggered, the vehicle’s parking lights will flash
for the full 30 second alarm cycle, attracting visual attention to the vehicle.
oOPTIONAL Whenever the system is triggered, the interior courtesy lights
will flash for the full 30 second alarm cycle.
oOPTIONAL Whenever the system is armed, the vehicle’s starting circuit
will be bypassed. If the thief should choose to ignore the siren, the vehicle
can not be started.
oOPTIONAL Any strong impact to the vehicle’s glass will cause the alarm
to trigger for the full 30 second alarm cycle.
DISARMINGTHESYSTEM
1. As you approach the vehicle, press and release the Unlock button on the
keychain transmitter.
þRed dash mounted LED turns off.
If passive arming was selected during the installation, then the LED will
start flashing rapidly, indicating that the system is re arming automati-
cally. Open any door to suspend the automatic arming.
þParking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in
your absence. Before turning the key on, examine the LED to identify
which zone was triggered.
þSiren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in

5
your absence. Before turning the key on, examine the LED
and refer to the INTRUSION WARNING SIGNALS section of
this manual to identify which zone was triggered.
If the siren did not sound when disarming, then the chirps
have been turned off, and you should refer to the section titled
“ELIMINATING THE ARM / DISARM CHIRPS” in this manual.
þDoors Unlock.
Using the optional Access Guard feature, the alarm can be
wired to unlock only the drivers door during this step. To unlock
all the doors, press and release the Unlock button of the
transmiter a second time within 3 seconds.
(Power Door Locks Required.)
oOPTIONAL Courtesy lights turn on for 30 seconds, or until the
ignition key is switched on.
SILENTDISARMING
1. As you approach the vehicle, press and hold the Unlock button on the keychain
transmitter for 2 seconds.
þRed dash mounted LED turns off.
If passive arming was selected during the installation, then the
LED will start flashing rapidly, indicating that the system is re
arming automatically. Open any door to suspend the automatic
arming.
þParking Lights flash two times.
If the parking lights flashed three times, then the alarm was
triggered in your absence. Before turning the key on, examine
the LED to identify which zone was triggered.
þSiren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in
your absence. Before turning the key on, examine the LED
and refer to the “INTRUSION WARNING SIGNALS” section of
this manual to identify which zone was triggered.
þDoors Unlock.
Using the optional Access Guard feature, the alarm can be
wired to unlock only the drivers door during this step. To unlock
all the doors, press and release the Arm/Disarm button of the
transmiter a second time within 3 seconds. (Power Door Locks
Required.)
oCourtesy lights turn on for 30 seconds, or until the ignition key is
switched on.

6
WHILETHE SYSTEMISSOUNDING
If during a triggered state, you wish to shut off the siren without disarming your
security system, simply press and release any transmitter button other than the
disarm button. This action will turn off the siren yet leave the vehicle fully armed
and protected. This feature is partictularily useful if you are aware of children
playing near your vehicle that may accidently trigger your security system. In this
case you can cancel the siren sounding without disarming your system.
INTRUSIONWARNINGSIGNALS
This system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4
times and the parking lights will flash 3 times when disarming the system. Enter
the vehicle and observe the red dash mounted LED to identify which zone was
triggered.
1) If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to the one of the pin switches typically
installed under the hood or in the trunk, or an optional sensor connected
to the unit.
2) If the LED is flashing two times...pause...two times...pause...etc., then
an intrusion attempt was made to a hood or trunk pin switch that was
added to the system, or to a light activated entry point if the alarm was
installed using the voltage sensing feature.
3) If the LED is flashing three times...pause...three times...pause...etc.,
then an intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory and will
only be erased when the ignition key is turned on.
VALETSWITCH
The valet switch allows you to temporarily bypass all alarm functions, eliminating
the need to hand your transmitter to parking attendants or garage mechanics.
When the system is in valet mode, all alarm functions are bypassed, however the
remote panic feature and remote door locks will remain operational. To use the
valet mode, the system must first be disarmed either by using your keychain
transmitter, or by activating your personalized manual override code.
1. Enter the vehicle and turn the ignition key to the on position.
2. Press and hold the valet pushbutton switch until the dash mounted
LED turns on solid. The system will remain in the valet mode.
3. To return to normal operation, press and release the pushbutton
switch any time the ignition is on.
NOTE: Always remember to exit the valet mode. This will ensure that the vehicle
remains protected at all times.

7
MANUALLYOVERRIDING YOURSYSTEM:
USINGTHEVALETSWITCHMANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmit-
ter. This is necessary, since you will need the ability to operate your vehicle if the
transmitter is lost or its battery fails. If your system has been selected for Valet
Switch manual override as indicated on the last page of this manual, to by-pass
the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the valet pushbutton switch.
The alarm system will stop sounding. You can now start and operate the vehicle
normally.
Typically this override mode is used only if the transmitter has become inoperative.
If this is the case, you may want to enter the valet mode until a operating or
replacement transmitter is available.
PROGRAMMINGTHECUSTOMCODEMANUALOVERRIDE
Unlike override switches easily found, and defeated, this security system allows
the consumer to program a personal override code, offering a higher level of
security. To take advantage of this option, programmable feature # 9 must be
selected for the Custom Code Option. Consult your installation center for pro-
gramming details. The system comes from the factory with a pre-programmed
override code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off
then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by
flashing the LED, first indicating the 10ths digit, pause and then the units digit.
The unit will report the new code three times with a one second pause between
each code, then the system will begin arming. If the LED flash pattern reports
the previously stored code, the new code was not entered correctly. Please
repeat steps 1 through 7 above considering the following.

8
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recog-
nize a 0 (Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would
do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the push button switch to set
the tenths digit.
(As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the push-button, turn the igntion switch
off then on.
7. Within 10 seconds, begin to press and release the push button switch to set
the units digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash
pattern.
You will note the LED flashing five times, pause and then flash two times, pause.
This pattern will be repeated three times indicating the new code (52) has been
accepted and stored in memory.
NOTE: If after step 7, the LED flashes a code other than what was just entered,
this indicates that the code has not been changed. You will have to repeat
steps 1 through 7 above being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0
(Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
MANUALLYOVERRIDING YOURSYSTEM:
USINGTHECUSTOMCODEOVERRIDE
Assuming the override code programmed has not been changed and the default
override code of 11 is in the system's memory.
1) Enter the vehicle and turn the ignition switch to the on position.

9
Note: The siren will sound.
2) Within 5 seconds, press and release the pushbutton switch 1 time.
3) Within 5 seconds, turn the ignition switch off then on.
4) Within 5 seconds, press and release the pushbutton switch 1 time.
5) Turn the ignition switch off then on and start the vehicle.
Note: If you have changed the programmed override code then substitute your
new code tenths for step 2 above, and units for step 5 above.
ELIMINATING THENORMALARM/ DISARMCHIRPS
As explained earlier in the manual, you can eliminate the chirps selectively any
time you arm or disarm the system simply by holding the ARM / DISARM button for
two seconds. If you find the normal arming and disarming chirps annoying, they
can be turned off permanently, eliminating the need to hold the ARM / DISARM
button for two seconds. To do this,
1. Turn the ignition key on then off.
2. Within 10 seconds, press and release push-button switch three times.
3. If the chirps were on before you started, then you will hear 2 chirps indicating
they have been turned off.
If the chirps were off before you started, then you will hear one chirp indicating
they have been turned on.
NOTE: Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3
chirp defective zone indicator will always operate. Since these are important
warnings to you that something has happened, they cannot be eliminated.
REMOTEPANICOPERATION
The Lock or Unlock button on your keychain transmitter also functions as a panic
switch for use in emergency situations. To use remote panic,
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or
more seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock or Unlcok button on the transmitter
again for 3 seconds. If the button is not pressed, the alarm will automatically
stop after 30 seconds. Also if any transmitter button other than the Lock or
Unlock button is pressed and released, the Panic mode will be turned off
immediately. The normal function of this transmitter button will be suspended
during the Panic sounding period.
NOTE: While in the Panic mode, pressing and releasing the Lock, or the Unlock
buttons will, if the option is installed, lock and unlock the doors respec-
tively. While in the panic mode, anytime the unlock button is pressed, the
the panic feature will continue for the alloted 30 seconds, however, the
security system will be disarmed allowing the vehicle to start.

10
OPTIONALDEVICE OUTPUT ( CHANNEL3)
ControlledBy:
oOption Button
oBoth Lock & Unlock Button
oBoth Option & Lock Button, or
oBoth Option and Unlock Button.
This security system is equipped with an output which will activate when the
appropriate transmitter button is depressed for 4 seconds. Optional devices that
may be connected to this channel are;
oRemote Electric Trunk Release
oRemote Car Starter
oRemote Window Closure
oRemote Garage Door Interface
NOTE: In addition there may be a second optional feature connected to your
system that when the same transmitter button is pressed and released 2
times within 3 seconds (double pressed), the second optional feature will
activate. This output is typically used for a remote start option and will
likely prevent inadvertent activation of the remote start device if young
children are playing with the hand held transmitter.
If your vehicle is not equipped with an electronic trunk release switch, or other
option listed, this feature may have been connected to another accessory. Please
ask your dealer for further information.
ADDITIONALREMOTEFUNCTION( CHANNEL4)
ControlledBy:
oOption Button
oBoth Lock & Unlock Button
oBoth Option & Lock Button, or
oBoth Option and Unlock Button.
This security system has an additional feature that can be connected to a number
of different optional accessories. Some of the more common uses for this chan-
nel are; oRemote Car Starter
oRemote Window Closure
oRemote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.