Audiovox UltraGuard PRO 9549UG User manual

Model PRO 9549UG
Owner’s Manual
Page 1
Dear Valued Customer,
The installation of the UltraGuard Security System on your vehicle has
been activated to provide you with the ultimate in vehicle protection. The
following features have been noted as standard in the installation of your
Auto Security System. Additional Security and Convenience features have
been noted under options and are available at an additional cost.
Standard Features:
2 Three Button Programmable RF Transmitters Four Channel Receiver
Code Hopping Technology Remote Panic in All Alarm Modes User
Programmable Override Code Intrusion Alert with Memory Audible Arm/
Disarm/Defective Zone Audible Tamper Confirmation Instant Siren Ac-
tivation Start Disable Last Door Arming Defective Zone By-Pass On
command RF Chirp Delete 6 Tone Siren Remote Keyless Entry* RF
Inhibit with Ignition ON Headlight Illumination during Arm/Disarm Pro-
grammable Features (refer to owner's manual) Infrasonic Shock Sensor
Remote Access Guard* Remote Trunk Release**
Optional Features:
7 Function L.E.D. Light Illuminated Entry Additional Engine Immobi-
lizer Parking Light Flash Vehicle Horn Activation Remote Start 
Remote Power Window Roll Up Remote Garage Door Interface Sport
Series Transmitter
* Vehicle must be equipped with Electronic Door Locks.
** Vehicle must be equipped with Electronic Trunk Release.
UltraGuard Security Systems 15600 Roscoe Blvd., Van Nuys, CA 91406 [phone]

Page 2
3 Button Remote Security System with
Shock Sensor, Starter Disable, & Keyless Entry
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need to
manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on " MANUALLY OVERRIDING YOUR SYSTEM " is
necessary to fully understand the procedure required to enable your vehicle in such situations.
In addition, the chart on the last page of this manual has a section for the particular features
and options installed in your vehicle as well as the override method selected. Valet Switch
manual override is pre-selected from the factory, however, the system can be configured
for "Custom Code" operation. Confirm the override mode selected on the last page of this
manual, and familiarize yourself with the selection on it's operation.
FEATURES :
2 Three Button Programmable RF Transmitters
Four Channel Receiver ( capable of accepting 4 transmitters )
Code Hopping Technology
Remote Panic in all modes
Protected Valet
User Programmable Manual Override Code (optional)
Intrusion Alert with Memory
Audible Arm / Disarm / Defective Zone / Tamper Confirmation
Instant Siren Activation
Starter Disable
True Last Door Arming ( hardwire only )
Defective Zone By - Pass
Hardwire or Voltage Sense Selectable
Active or Passive Arming Selectable
Programmable Auto Lock On / Off
Programmable Auto Unlock On / Off
Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds
Programmable Active or Passive Door Locks
User Programmable Permanent Chirp Delete
On Command RF Chirp Delete from Transmitter
6 Tone Multi - Tone Siren
Car Horn Activation for additional alarm response
Additional Negative Trigger Input
RF Inhibit with ignition on
Access Guard
Plug In Electronic Shock Sensor
Headlight Illumination during Arming and Disarming
Remote Keyless Entry with optional Access Guard (must have power door locks)
Illuminated Entry
Remote Trunk Release (must have electronic trunk release)
OPTIONS :
Illuminated Entry
Multiple Vehicle Capable
Parking Light Flasher
Remote Starter
Remote Power Window Roll Up
Remote Garage Door Interface

Page 3
YOUR “ CODE HOPPING “ TRANSMITTERS
The transmitters included with your new security system use the most advanced and secure
form of radio frequency transmission available on any current automotive security system.
Some of today’s sophisticated auto thieves use a device known as a code grabber, which will
receive and store the signal from your keychain transmitter, and re-transmit at a later time to
disarm your system.
Your code hopping transmitters will change their signal every time the button is pressed, so
when a thief grabs then re transmits your signal, the alarm system will not respond.
If your transmitter button is pressed more than fifty times while it is out of range of the vehicle
( children playing with your keys ), the transmitter will not operate when you return to the
vehicle, and will need to be re-aligned to the receiver. To do this, simply press button 1 two
times within a one second time period. The system will now re-
spond to that transmitter each time a button is pressed.
ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood
lid, and trunk lid.
2. Quickly press and release the Lock, Arm/ Unlock, Disarm button
on the keychain transmitter.
Siren sounds one chirp.
If the siren sounds 3 chirps, then you have left a door,
trunk, or hood lid ajar. Simply close the opened entry point to provide full protection.
If the siren did not sound when arming, then the chirps have been turned off,
and you should refer to the section titled “ ELIMINATING THE ARM / DISARM
CHIRPS “ in this manual.
Doors Lock.
Headlight Illumination.
The vehicle’s headlights turn on for approximately 30 seconds, illuminating the
path as you leave the vehicle.
SILENT ARMING - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and hold the Lock, Arm/ Unlock, Disarm button on the keychain transmitter for 2 seconds.
Doors Lock.
Headlight Illumination.
The vehicle’s headlights turn on for approximately 30 seconds, illuminating the
path as you leave the vehicle.
DISARMING THE SYSTEM
1. As you approach the vehicle, quickly press and release the Lock, Arm / Unlock, Disarm
button on the keychain transmitter.
Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. If the
siren did not sound when disarming, then the chirps have been turned off, and you
should refer to the section titled “ ELIMINATING THE ARM/DISARM CHIRPS “ in
this manual.
Doors Unlock.
Using the optional ACCESS GUARD feature, the alarm can be wired to unlock only
the driver’s door during this step. To unlock all doors, press and release the Lock,

Page 4
Arm / Unlock,Disarm button a second time within 3 seconds.
Headlight Illumination.
The vehicle’s headlights turn on for approximately 30 seconds, illuminating the path
to the vehicle.
SILENT DISARMING
1. As you approach the vehicle, press and hold the Lock, Arm / Unlock,Disarm button on the
keychain transmitter for 2 seconds.
Doors Unlock.
Using the optional ACCESS GUARD feature, the alarm can be wired to unlock only
the driver’s door during this step. To unlock all doors, press and release the Lock,
Arm / Unlcok, Disarm button a second time within 3 seconds.
Headlight Illumination.
The vehicle’s headlights turn on for approximately 30 seconds, illuminating the path
to the vehicle.
VALET SWITCH
The valet switch allows you to temporarily by-pass all alarm functions, eliminating the need to
hand your transmitter to parking attendants or garage mechanics. When the system is in valet
mode, all alarm functions are by-passed; however, the remote panic feature and remote door
locks will remain operational. To use the valet mode, the system must first be disarmed either
by using your keychain transmitter, or by activating your personalized manual override code.
1. Enter the vehicle, and turn the ignition key to the on position.
2. Move the valet toggle switch to the on position.
3. To return to normal operation, move the valet switch back to the off position any
time the ignition is on.
NOTE : Always remember to move the valet switch back to the off position. This will ensure that
the vehicle remains protected at all times.
USING THE VALET SWITCH MANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmitter. This is
necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its
battery fails. If your system has been selected for Valet Switch manual override as indicated on
the last page of this manual, to by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Start with the Valet Switch in the off position.
3. Turn the ignition key to the on position.
4. Within 5 seconds, turn the valet switch to the on position.
The alarm system will stop sounding and enter the valet, (by-passed) mode. This is indicated
by the dash mounted LED turning on. You can now start and operate the vehicle normally. To
return to normal operation, move the valet switch back to the off position any time the ignition is
on.
OPTIONAL:
This programmable manual override is an optional feature that can be activated by your car
dealer.
PROGRAMMING THE CUSTOM CODE MANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmitter. This is
necessary, since you will need the ability to disarm the system if you lose your transmitter, or if
the transmitter battery fails.

Page 5
If your system has been selected for Custom Code manual override as indicated on the last
page of this manual, in order to provide the highest level of security, this system will allow you
to program your personal manual override code. This code isa(2)digit code. The first digit
must be a digit from 1 through 9, and the second digit must be either 1, 2, or 3.
To program your access code, the security system must be in the disarmed state. Once dis-
armed, program your code as follows;
1. Turn the ignition key on, then off, then on.
2. Within 3 seconds of step 1, flip the Valet switch on, then off. The siren will sound
one short chirp, followed by one long chirp. This indicates that the system is in the
manual override programming mode.
3. The red dash L.E.D. will begin to count by flashing. Allow the L.E.D. to flash until
it gets to the first digit of your selected code.
4. As soon as the L.E.D. turns on for the corresponding number of your first digit,
quickly turn the ignition key;
1. off then on for second digit 1
2. off then on twice for second digit 2
3. off then on three times for second digit 3.
5. The siren will sound one short chirp, followed by one long chirp, indicating that the
code has been memorized.
6. After a 2 second pause, the L.E.D. will flash confirmation of the stored code,
beginning with the first digit, then a pause, then the second digit.
EXAMPLE : To program the manual override code 52, you would;
1. Turn the ignition key on, then off, then on.
2. Within 3 seconds of step 1, flip the Valet switch on, then off. The siren will sound
one short chirp, followed by one long chirp. This indicates that the system is in the
manual override programming mode.
3. Allow the L.E.D. to flash 5times, and during or immediately after the fifth flash,
quickly turn the ignition key to off, then on, then off, then on.
4. The siren will sound one short chirp, followed by one long chirp, indicating that the
code has been memorized.
5. After a 2 second pause, the L.E.D. will flash 5times, then pause, then flash 2
times. This confirms that the code 52 has been stored into memory.
USING THE CUSTOM CODE MANUAL OVERRIDE
It is very important that you understand how to operate the manual override feature, as there
may a time that you will need to bypass the alarm when your transmitter is not working. You
should also write down your personalized code number, and keep it in a safe place for future
reference.
To by pass the alarm,
1. Open the door. The alarm will sound.
2. Turn the ignition key to the on position. The alarm will stop for three seconds, then
the siren will begin counting with long chirps.
3. As soon as the chirp that corresponds with your first digit sounds, quickly turn the
ignition key ;
1. off then on if your second digit is 1
2. off then on twice if your second digit is 2
3. off then on three times if your second digit is 3.

4. The alarm will stop sounding, and you can now start the vehicle.
EXAMPLE : To override the system using the example 52 above, you would,
1. Open the door. The alarm will sound.
REMOTE PANIC OPERATION
The Lock,Arm / Unlock, Disarm button on your keychain transmitter also functions as a panic
switch for use in emergency situations. To use remote panic,
1. Press and hold the Lock,Arm / Unlock, Disarm button on the keychain transmitter
for 3 or more seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock,Arm / Unlock, Disarm button on the
transmitter again for 3 seconds. If the button is not pressed, the alarm will auto-
matically stop after 30 seconds.
NOTE : All normal transmitter functions will operate in the panic mode.
REMOTE TRUNK RELEASE ( CHANNEL 2 )
This security system is equipped with an on-board trunk release relay which will activate the
existing factory installed electronic trunk release switch. If your vehicle is not equipped with an
electronic trunk release switch, this feature may have been connected to another accessory.
Please ask your dealer for further information.
To remotely open the trunk, press and hold the Trunk button on the keychain transmitter for four
seconds.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 ) OPTION
This security system has an additional feature that can be connected to a number of different
optional accessories. Some of the more common uses for this channel are;
Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To activate the optional accessory, press the option button on the keychain transmitter. The
optional accessory will immediately engage.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 ) OPTIONS
This security system has an additional feature that can be connected to a number of different
optional accessories. Some of the more common uses for this channel are;
Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To activate the optional accessory, press both the trunk and option buttons on the keychain
transmitter simultaneously. The optional accessory will immediately engage.

PRO 9549UG
SYSTEM FUNCTIONS AT A GLANCE
SIREN AND / OR HORN CHIRP INDICATORS
1 CHIRP * = ARM
2 CHIRPS * = DISARM
3 CHIRPS = ARM / DOOR OPENED
4 CHIRPS = DISARM / INTRUSION
* These chirps are optional, and can be de - activated.
Your System Has These Features Activated
Auto Lock with ignition key
Auto Unlock with ignition key
Headlight Illumination during arm & disarm
Passive Arming
No Lock in passive mode
Hardwire doors, hood, and trunk