Audiovox PurSuit PRO-9056TW User manual

128-8856b
1 of 4
1
Single Channel Remote Car Starter
Model Pro9056TW
Owner’sManual
FEATURES :
1 Programmable RF Transmitter, 1 Programmable RF Transceiver
Single Channel Receiver (capable of accepting 4 transmitters)
External Superheterodyne Receiver Antenna w/PushButton Switch &
LED
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
Two ( + ) and Two ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
AccessoryOutputs
(PulseBefore&AfterStart,DuringCrank&AfterShutDown)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20, 45, and 60 Minute Run Time
Car Finder Mode
Optional Door Unlock Feature For Vehicles Equipped With Power Doors
(Only operational while running under control of the remote start unit.)
Rev A: Add new URL 11/4/2011
Rev B: New Format 5/2013
PATENTED: www.voxxintl.com/company/patents

128-8856b
2 of 4
2
REMOTESTARTINGTHEVEHICLE
This will not start the vehicle if any one of the following situations
exists:
The vehicle's hood lid is opened.
The gear shift selector is not in Park.
The brake pedal is depressed.
The safety control switch is in the Off position.
1. To start the vehicle, press and release the
transmitter button two times within 2 seconds.
The vehicle will start and remain running for the
pre-programmed time of up to 60 a minute run
cycle. As a visual indication, the parking lights
will flash or remain on depending on the setting
by your installation center. Additionally if the two way trans-
ceiver, shown right, is used, the transceiver will play a melody
when the vehicle is started, and the Orange LED surrounding the button will
flash every ten seconds while the vehicle is running.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the
spring loaded start position), then step on the brake pedal to disengage the
remote starter. The vehicle will continue to run, but now on its own power.
NOTE: The engine will stop running before the pre-programmed run cycle
has expired if you perform any one of the following functions:
Press and the button on the keychain transmitter two times within 2 seconds
Depress the brake pedal
Open the vehicle's hood
Place the unit in the safety control disabled mode.
PUSH-BUTTONLEDRECEIVERVALET/OVERRIDE/SAFETYCONTROLSWITCH
The Push-Button LED switch located in the receiver allows you to temporarily
disable the remote starting function of the system. This is recommended when-
ever the vehicle is being serviced. To place the system in the service mode:
1. With the system disarmed/unlocked, and the ignition switch off, press and
hold the Push-Button, found on the windsheild receiver.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED begins to flash two short flashes followed by one long flashes and
continues this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start
is in the service mode and will not start from RF or any other input Posse
or otherwise.
To Exit R/S Override Mode:
1. With the system disarmed, press and hold the Push-Button, found on the
windsheild receiver, in.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED turns off indicating that the R/S unit is fully functional once again.

128-8856b
3 of 4
3
UNLOCKINGTHEVEHICLE:
If you have an electric door lock, and the Optional Unlock feature was added,
with the vehicle running under command of the remote start unit, press and
hold the transmitter button for 3 seconds until the doors unlock.
CARFINDERMODE:
Anytime the vehicle is not running under control of the remote start unit, within
operating range of the vehicle, press and hold the push-button of the hand
held transmitter for 4 seconds to activate the car finder mode. The vehicle
lights will flash for 30 seconds or until the push-button is again pressed
and released.
TELEMATICUPGRADE:
This system has the ability to have a telematic upgrade module connected to it.
This is an upgrade that can give you control of certain functions of your vehicle
from a telephone, or in some cases a computer interface. Please check with
yourinstallation centerfor most recentTelematic Upgrades.If youhada Telematic
Upgrade installed, the manual supplied with the upgrade unit will provide an
operator's manual advising of the features of the system and means available
to control these features of your vehicle.
PROGRAMMINGNEW ORREPLACEMENTTRANSMITTERS(BANK 1)
The Transmitter Model Name Is Found On Back Of Transmitter Case.
1. Turn the ignition key to the on position.
2. Press and release the valet/programming switch 3 times (Siren Chirps).
3. Press the Lock Button of each transmitter you want programmed until you
hear a chirp from the horn or siren.
4. Turn the ignition switch off.
The above action programs the Lock, Unlock, Start/Trunk, and Option 1 buttons
which are typical for most systems.
For additional channel programming beyond the 1 option button, you can use
any unused button or combination of buttons not in use.
In other words, to access option channel 5, 6, 7, you would do the following:
From step 3 above:
a. Press and release the valet/programming button 4 additional times to get to
channel 5, then Press any unused transmitter button or button combination
to program.
b. From a, press and release the valet/programming button 1 time to get to
channel 6, then press any unused transmitter button or button combination
to program.

128-8856b
4 of 4
4
To purchase replacement transmitters
or to get additional product information go to:
www.pursuitcarsecurity.com
© 2013 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8856b
c. From b, press and release the valet/programming button 1 time to get to
channel 7, then press any unused transmitter button or button combination
to program.
NOTE: Not all systems have channels above 3, check with your installation center
for options your system may or may not have.
NOTE: Certain systems have the ability to utilize channels 6 & 7 for driver
priority programming. For driver priority, the vehicle must be equipped
with this feature, and the optional feature must be set up and installed
by your installation center. Once this feature is added when the unlock
button of transmitter 1 is used, it will set driver 1 priority, and when the
unlock button of transmitter 2 is used it will set driver 2 priority. In this
situation, the unlock button can be programmed into two receiver
channels, unlock, channel 2 and driver priority 6 or 7. In no other
circumstance will the system allow a transmitter button to be
programmed into 2 receiver channels at the same time.
FUNCTIONSETTINGCHART
To be completed by installer:
Run Time 5 Min 10 Min 15 Min 20 Min 
While Running Unlock Yes No 
Lights Pulse Steady 