Aura AFADI01R-CH Series User manual

Please read notices on following page
Dimensions of xtures are approximate and may vary ± 6mm (1/4”). Structure measurements must be veried against the unit to ensure proper t.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Manual
Model: AFADI01R-CH
Faucet
Aura Single Hole Lavatory Faucet
Installation Manual

Installation Manual
AFADI01R-CH *** Faucet
Dimensions of xtures are approximate and may vary ± 6mm (1/4”). Structure measurements must be veried against the unit to ensure proper t.
Product images and specications are for illustrative purposes only, product design may vary.
GENERAL INSTRUCTIONS
• Read this guide carefully and completely before proceeding.
• It is recommended that you wear safety glasses during the installation.
NOTICE
• For best results, we recommend that a licensed, professional plumber installs this unit.
• Please read over these instructions thoroughly before beginning installation.
• Make sure that you have all tools and supplies needed to complete the installation.
• Please check local building code.
• IF SOLDERING, REMOVE CARTRIDGES TO PREVENT DAMAGE
• Keep receipts (proof of purchase and place of purchase) for this product. The receipt is required should it be necessary to request warranty parts.
MAINTENANCE & CARE FOR YOUR AURA PRODUCTS
• To clean your faucet or accessory, when necessary, wash with a nonabrasive wet soapy cloth. Then wipe dry with a soft towel or cloth.
• Do not use any abrasive chemical or corrosive powders, detergents, window cleaners, disinfectants or any other strong cleaners on your Product
as they will destroy the nish and therefore void the warranty
REMOVAL OF FAUCET
• Always turn the water supply o before removing the existing faucet or disassembling a faucet.
• Ensure the water has been turned o.
2
4"
1"
5"
PHILLIPS
SCREWDRIVERS
PENCIL WRENCH THREAD SEALANT ALLEN KEY GROOVE JOINT
PLIER
Materials and Tools Required
Important Measurements

Installation Manual
AFADI01R-CH *** Faucet
Dimensions of xtures are approximate and may vary ± 6mm (1/4”). Structure measurements must be veried against the unit to ensure proper t.
Product images and specications are for illustrative purposes only, product design may vary.
Parts List
3
1
2
3
4
5
6
7
8
9
10
12
13
14
15
11
ITEM DESCRIPTION SKU QTY
1Handle 1
2Cartridge Cover 1
3Retaining Nut 1
4Washer 1
5Cartridge 1
6Aerator (1.5GPM) 1
7Mixer Body 1
8Base 1
9O’Ring 1
10 Thread Pipe 1
11 Plastic Nut 1
12 Flexible Hose 2
13 Drain with Overow 1
ITEM DESCRIPTION SKU QTY
14 Set Screw 1
15 Cap 1
16
17
18
19
20
21
22
23
24
25
26

Installation Manual
AFADI01R-CH *** Faucet
Dimensions of xtures are approximate and may vary ± 6mm (1/4”). Structure measurements must be veried against the unit to ensure proper t.
Product images and specications are for illustrative purposes only, product design may vary.
4
Unscrew the Bottom Tube (8) and remove the
Brass Hexagonal Nut (6), and the Plastic Washer
(5).
Insert the top body of the drain: Pop-Up Drain (1),
Drain (2), Curved Rubber Washer (3) into the hole
of the sink.
Reinsert the Curved Rubber Washer (4) and the
Brass Hexagonal Nut (6) below the sink.
Tighten rmly without putting pressure on the sink.
Screw the Bottom Tube (8) back on.
2A.
(2)
(5)
(6)
(8)
(7)
Top Body
(3)
(1)
(4)
Sink Drain Hole
2A.
(1)
(2)
(3)
(4)
(5)
(2)
(3)
(4)
(5)
Hot In Cold In
Drain Installation
Faucet Installation
1B. 1C.1A.
(1)
(2)
(3)
(4)
(5)
(6)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Faucet
Chrome Base
Rubber Washer
Metal Washer
Plastic Nut
Flex Hose
Pop-Up Drain
Drain
Curved Rubber Washer
Bowl Rubber Washer
Plastic Washer
Brass Hexagonal Nut
Rubber Washer
Bottom Tube
(1)
Flex Hoses
(6)
Mounting Kit
Faucet
ATTENTION!
TIGHTEN HOSES BY HAND ONLY
Remove the mounting kit below the Faucet (1)
If Not already attached, attach both ex hoses to
the faucet (hand tighten only).
Insert Flex Hoses (6) through the hole of your sink
or countertop, then place the faucet inserting the
threaded end in your sink or countertop.
Insert the Rubber Washer (2), the Metal Washer
(3) and secure the Faucet (1) with the Plastic Nut
(5).
Connect the hot and water hoses to the inlet shut
o valves.
1A.
1B.
1C.

Installation Manual
AFADI01R-CH *** Faucet
Dimensions of xtures are approximate and may vary ± 6mm (1/4”). Structure measurements must be veried against the unit to ensure proper t.
Product images and specications are for illustrative purposes only, product design may vary.
5
Cartridge Repacement
(1)
(2)
(3)
(4)
(5)
(6)
(8)
(7)
3A.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Handle
Cartridge Cover
Retaining Nut
Washer
Cartridge
Faucet
Set Screw
Cap
Shut o the water supply lines and then pull Handle
(1) to turn the water on so it drains the Faucet (6).
To replace the Cartridge (5) remove the Cap (8)
that covers the Set Screw (7) and loosen the Set
Screw (7).
Pull the Handle (1) o the Faucet (6).
Untighten the Cap (4) covering the Retaining Nut
(5), and then unscrew the Retaining Nut (5) which
holdes the Cartridge (5) into place.
Note the Orientation of the old cartridge, to place a
new carridge in the same position.
Pull the old Cartridge (5) out and replace with a
new one. Align the bottom pins on the Cartridge to
t into holes in the Faucet (6).
3A.