Auscrown RB18NG Manual

Wok Burner Cooker Installation & Operating Instructions
1
INSTALLATION & OPERATING INSTRUCTIONS
WOK BURNER COOKERS
FOR INSTALLATION AND USE INDOORS ONLY
- NOT FOR PORTABLE USE -
AGA APPROVAL NO.: 7092G
Rambo®
Models for use with Natural Gas:
Models for use with Natural Gas:
RB18NG - Single Burner Wok Cooker
RB28NG - Double Burner Wok Cooker CK801NG – Single Burner Wok Cooker CK802NG – Double Burner Wok Cooker
Models for use with Propane Gas:
CK801PG – Single Burner Wok Cooker
CK802PG – Double Burner Wok Cooker
FEATURES
Electronic ignition system incorporating piezo-electric elements.
Wok burner suitable for all types of cooking from simmering to stir-frying.
High-energy, high-efficiency burner reduces gas consumption.
Removable control knob incorporating burner ignition.
Large trivet for greater cooking flexibility.
Easy to clean stainless steel top and control panel.
IMPORTANT
The appliance must be installed only by an authorised person such as a licensed gas fitter or plumber.
Read this manual carefully and retain for future reference.
THE APPLIANCE MUST BE INSTALLED IN COMPLIANCE WITH THE FOLLOWING:
AS5601 – Australian Standard for Gas Installations;
Manufacturer’s installation instructions;
Local gas fitting regulations;
Municipal building codes; and
Any other relevant statutory regulation(s).
GAS PRESSURE REGULATOR DETAILS
FOR NG MODELS
A natural gas regulator is included with the appliance – Maxitrol RV20LM, AGA Approval No. 3088
FOR PG MODELS
A gas regulator and hose assembly is included with the appliance.
THE CORRECT FITTINGS MUST BE USED AT ALL TIMES - DO NOT USE ADAPTORS
Important: Read these instructions carefully before use. Familiarize yourself with the appliance
before connecting it to its gas supply. Keep these instructions for future reference.

SAFETY WARNINGS
This appliance must be used in a well ventilated area only
DO NOT USE IN MARINE CRAFT, CARAVAN OR MOBILE HOMES.
Failure to follow instructions in this manual could result in physical injury and/or property
damage.
Hazardous fire or explosion may result if instructions are ignored
Leak-test all connections before use
Never check for leaks with a match or open flame
Do not store or use petroleum products or other flammable vapours and liquids in the vicinity of
this appliance
Do not use or store flammable materials in the appliance storage drawer or near this appliance.
Carbon monoxide hazard – this appliance can produce carbon monoxide which has no odour.
Using the appliance in an enclosed space may cause death. This appliance is not for
installation inside a caravan, tent, car, mobile home.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
Do not use this appliance as a space heater under any circumstance.
Any LP cylinder not connected for use with this appliance shall not be stored near this
appliance.
This cooker is suitable for use with the specified gas type only. The cooker is only to be
connected to the gas type specified on the label/data plate.
Do not modify this appliance or changed in any way.
Do not use this cooker where petroleum products or other liquids having flammable vapours
are stored or used.
Children and adults should be alerted to the high temperatures of the cooker and its effect on
surrounding surfaces, clothing and skin
Children or the elderly should be supervised when near this appliance
Do not hang clothing or other flammable material on or near this appliance
Do not cover or blow out the flames. This could cause gas leaking.
Always keep flammable materials away from the cooker.
Do not store things close to the cooker.
Install and use the cooker in a well-ventilated area.
Make sure that you use cooking woks, pots or pans that sit firmly on the trivet. Do not use pots
that are too small/large for the burner size, as they could be unstable on the trivet.
If abnormal combustion is observed when in use, turn off the main gas valve and examine the
cooker (refer to trouble-shooting guide)
A SPIDER’S WEB CAN INTERFERE WITH THE FLOW OF GAS / AIR INTO THE BURNER, THE
OPENING INTO THE BURNER DIRECTLY IN FRONT OF THE GAS VALVE SHOULD BE CHECKED
REGULARLY AND CLEARED WITH A PIPE CLEANER OR SIMILAR LENGTH DEVICE. (SEE
MAINTENANCE)
FOR YOUR SAFETY – WHAT TO DO IF YOU SMELL GAS
The strong and distinctive odour of gas may make you aware of a gas leak. If you suspect a gas
leak:
Extinguish all naked flames
Immediately turn off all appliances and pilot lights.
Do not allow gas to build up in the area. Open all doors and windows to both disperse the gas
and provide ventilation of fresh air.
Allow sufficient time for any accumulated gas to disperse
Ensure all persons are evacuated
Turn off the gas supply at the source (gas meter, gas bottle etc.) and contact an authorised gas
fitter immediately.
It must be serviced and repaired by a licensed plumber or gas fitter.
NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF

INSTALLATION – NOTES TO THE INSTALLER
APPLIANCE MUST BE INSTALLED ONLY BY A LICENSED GASFITTER OR
PLUMBER.
INSTALLATION
Position of Wok Cooker outlet pipe at the rear of the unit:
RB18 / CK801 RB28 / CK802
SAFETY PRECAUTIONS
MAKE SURE YOU AND YOUR LICENSED GAS FITTER/PLUMBER CAREFULLY READ ALL OF THESE
INSTRUCTIONS BEFORE INSTALLING THE COOKER. FOLLOW ALL WARNINGS AND
INSTRUCTIONS MARKED ON THE COOKER.
Do not install a damaged cooker. Contact your service agent or supplier if the cooker is
damaged.
Check the gas type of the cooker and make sure it is suited for the type of gas supplied.
Make sure the gas inlet pipe is clean and not blocked before connecting the gas.
Selecting a suitable position for the cooker is important to ensure maximum performance,
economy and safety of operation.
Always ensure that adequate fresh air is provided for ventilation.
The cooker must only be operated on a level, firm non-combustible surface.
This cooker shall not be installed in a position where it could create a fire hazard and the
minimum clearances to combustible materials must be observed, as described below.
SERVICE INSTRUCTIONS FOR LISCENSE GAS FITTER OR PLUMBER.
(a) Remove all covers and other parts for access to all components.
(b) Remove all components for services.
CLEARANCES
This cooker must be installed so that a vertical clearance of at least 1200mm is maintained
between its burners and any combustible material. Where it is not practical, the underside of
any combustible material with a vertical clearance of less than 600mm above a burner should
be protected by mill-board at least 6mm thick which is covered with sheet metal not less than
0.4mm thick, or protected by an equivalent material extending at least 225mm beyond the
sides of the cooker. In either case, the vertical clearance above the cooker burner should not
be less than 450mm.
The minimum clearance from the cooker to rear or sides of combustible surfaces must be no
less than 250mm. When the cooker is installed abutting a side or rear wall, the wall must be of
non-combustible material, e.g. ceramic tiles. If surrounding walls are constructed with a
combustible material, contact your local Gas Authority for information on clearances required.
Combustible material Range hood

1. Remove all the packing materials from the cooker before
connecting the gas.
2. The piping should not be assembled beneath the cooker,
under direct sunlight and close to other sources of heat.
3. Unit Gas inlet fitting located at the rear of the cooker: ¼ ”
BSPM 60o coned
4. Ensure that the gas supply connection point is accessible
when the cooker is installed.
5. Connecting the gas pressure regulator:
For Natural Gas (NG) Models:
-Screw the ¼” threaded female end of the NG Regulator onto the inlet connection at the
rear of the cooker and tighten with a suitable spanner. Make sure that the direction
arrow on the regulator points towards the cooker.
-The gas pressure regulator inlet fitting is of ½” BSP female. The connection of piping
must be made suitable to connect to the regulator inlet to provide a secure connection
free of gas leakage.
For Propane Gas (PG) Models:
-The connection fitting required is ¼” BSP female threaded swivel nut with 60o inverted flare.
Connection to piping must be made suitable to connect to the regulator inlet to provide a
secure connection free of gas leakage.
Fix the cooker onto the bench by drilling holes into the bench top to the position of the fixing
brackets. Place brackets into position on the cooker over the burner support beam and screw into
position using the supplied screws. Screw the brackets securely to the bench top using the
appropriate nut and screws
6.
7. Check for gas leakage at all joints with soapy water or other approved methods.
SAFETY INSTALLATION OF THE REULATOR AND HOSE ASSEMBLY
8. The installation of the regulator and hose assembly must follow the Australian Standard
AS5601.
9. The regulator and hose must be AGA approved.
10. The hose and regulator should not be assembled beneath the cooker, under direct sunlight and
close to other sources of heat.
11. Make sure the hose is not strained or twisted.
12. The hose must not exceed 1.8 metres in length.
13. Use a spanner to connect the hose and regulator, all connections must be gas tight
14. Check for gas leakage at all joints with soapy water or other approved methods.
. UNDER NO CIRCUMSTANCES SHOULD A NAKED FLAME BE USED IN CHECKING
FOR GAS LEAKS.
ALTERNATIVE INSTALLATIONS
There are no alternative methods of installations and connections
GAS REGULATOR (LOW PRESSURE) DETAILS
Natural Gas (NG) Models
Maxitrol RV20LM Appliance Regulator AGA Approval No. 3088 (SUPPLIED)
-Pressure: 1.0 kPa
-Inlet: 1/4" BSP Female
-Outlet: 1/4" BSP Female
Or an equivalent AGA approved natural gas regulator with the same fitting.
PRESSURE ADJUSTMENT OF THE REGULATORS
Never adjust the pressure of the regulators. The natural gas regulator is already adjusted to the
right pressure of 1kPa and the LP gas regulator to 2.8 kPa plus/minus 0.05
If you suspect the pressure of the regulator is abnormal, please contact Austcrown Pty Ltd for
assistance.

CORRECT ASSEMBLY OF BURNER HEAD
FOR CK801NG/PG and CK802 NG/PG Models Only
TO GAS FITTERS - BEFORE LEAVING AFTER INSTALLATION
1. Make sure all connections are gas tight and have no gas leakage.
2. Check that the aeration control is adjusted to the right position to enable the burner to achieve
a blue and vigorous flame to reach complete combustion.
3. Make sure the flame is normal when adjusted to low flame; there should be no yellow flames at
anytime.
4. Check there is no backfire when the appliances is turned down to low or turned off.
5. The main gas supply valve is off
6. The gas control on the appliance is off
7. The consumer fully understands the safety precautions, operation and maintenance
8. The operation of the ignition system is satisfactory.
9. If a normal flame cannot be achieved after adjusting the aeration control plate, please contact
Austcrown Pty Ltd for assistance.
APPLIANCE DIMENSIONS
RB18/CK801 RB28/CK802

COMPONENTS AND PARTS
RB18NG RB28NG
PARTS INDEX
1. Trivet 3. Inner Ring Burner 5. Ignition/Control Knob 7. Rubber Leg
2. Outer Ring Burner 4. Body 6. Tray
CK801NG & CK801PG CK802NG & CK802PG
PARTS INDEX – NG AND PG MODELS
1. Body 3. Outer Ring Brass Cap 5. Tray 7. Rubber Leg
2. Trivet 4. Inner Ring Brass Cap 6. Burner Head 8. Knob
OPERATING INSTRUCTIONS
USING THE COOKER
Follow these steps when operating the cooker:
LIGHTING THE COOKER
1. Make sure the ignition knob set to the ‘OFF’ position.
2. Push in and turn the ignition knob anti-clockwise until a “click”
sound is heard. Make sure the burner has been lit properly.
ADJUSTING THE FLAME
1. Turn the ignition knob to the required flame setting position as shown below.
Lighting the cooker
ON
OFF

TURNING OFF THE COOKER
1. Turn the ignition knob fully back to the OFF position until a
“click” sound is heard. Make sure there is no flow of gas
through the burner.
CAUTION - CORRECT PLACEMENT OF UTENSILS
MAINTENANCE
Keep the cooker clean regularly by wiping with a damp cloth.
Before checking and maintaining the cooker, make sure the main gas valve is turned off.
Make sure the burner head(s) is/are clean before using the cooker. Use a steel wire brush to
clean the burner if it is heavily clogged. If the burner is heavily clogged, do not use the unit.
Contact your authorised plumber or gas fitter to carry out cleaning and maintenance. Do not
attempt to remove the burner unit(s) yourself.
Check the gas pipes regularly for wear or leaks. If any wear or leaks are presents, please
contact an authorised plumber / gasfitter for repair.
Do not touch the burner, trivet, tray etc. immediately after use or when in use. This could burn
your hand.
Clean the trivet and tray after each use. Always wipe off spills, do not leave spills to dry on the
surface of the trivet, tray or burner.
Inspect the electrodes carefully after you have removed the tray receptacle and if soiled, clean
with a dry cloth.
For model CK801/802 only - Wash the burner head and burner cap with a moist and soaped
sponge or cloth. Do not put them in cold water immediately after use as thermal shocks could
cause cracking.
CLEANING VENTURI OR INJECTOR BLOCKAGE (FOR LICENCED GAS FITTER ONLY)
1. Turn off main gas supply.
2. Disconnect regulator or hose from gas supply.
3. Remove all trivet/s, tray/s and Burner Caps (CK801/802 only).
4. Turn over the cooker.
5. Remove the clip that hold on the burner head.
6. Remove the burner head from the cooker.
7. Check venturi (inlet) of the burner. Clean venturi with a long narrow screwdriver.
8. Check injector at the gas valve. Clean the injector with pipe cleaner or thin metal wire.
9. Replace burner head back to the cooker. Ensure the injectors are inserted correctly into the
centre of the air flow adjusting plate (a circular cut out).
10. Ensure to insert the clip to lock on the burner head.
Turning off the cooker
ON
OFF
Do not place
anything e.g.
Flame tamer,
asbestos mat
etc. Between pan
and pan support
as serious
damage to the
appliance may
result.
Do not remove
the pan support
and enclose the
burner with a
wok stand as this
will concentrate
and deflect heat
onto the hotplate.
Do notuse large
pots or heavy
weights which
can bend the pan
support or deflect
flame onto the
hotplate.
Locate pan
centrally over the
burner so that it
is stable and
does not
overhang the
appliance.
Use only wok
support supplied
or recommended
by the
manufacturer of
the appliance

11. Turn over the cooker, ensure it seat secure.
12. Replace Burner Caps (CK801/802 only)
13. Ensure the gas valve is a OFF position.
14. Connect the regulator or hose to the main gas supply.
15. Turn on gas supply.
16. Check gas leak. (See section “How to check for gas leaks”)
17. Ignite the burner. (See section “Lighting the Cooker”)
TROUBLESHOOTING
Problem Possible Cause Solution
No Ignition
Main Gas Valve is not turned
on.
Air trapped in the gas hose.
Electronic ignition is wet or
dirty.
The safety valve is not open.
Turn off the gas valve once and then turn it on fully.
Repeat the ignition process until all air in the hose is purged
completely.
Clean and wipe the electrode with a dry cloth.
Push in the ignition knob and turn it anti-clockwise until a click
sound is heard. Ensure the burner has been lit. Press the ignition
knob for 3-4 seconds and release the knob.
Gas Leaking
Failure of the gas valve. Contact your dealer for a service/repair.
DO NOT ATTEMPT TO REPAIR IT YOURSELF.
Incomplete
Combustion
(Yellow
Flame)
Aeration shutters are not
properly adjusted.
Burner is not properly
assembled.
Flame holes of the burner
are clogged.
Nozzle is clogged.
Contact a gas fitter to adjust the aeration shutters to achieve the
optimum air/gas intake ratio.
Position the burner body properly.
Clean the burner head and the burner cap.
Contact your dealer for a service/repair.
DO NOT ATTEMPT TO REPAIR IT YOURSELF.

CONVERSION
This cooker is suitable for use with propane gas only and may not be converted for use on any other type of
gas, for further advice, contact place of purchase or their authorised agent for advice.
SERVICE INSTRUCTIONS FOR LISCENSE GAS FITTER OR PLUMBER.
(a) Remove all covers and other parts for access to all components.
(b) Remove all components for services.

TECHNICAL SPECIFICATION
Model Number RB18NG CK801NG RB28NG CK802NG CK801PG CK802PG
Heat Capacity (MJ/hr) 14.20 15.8 28.40 31.6 13.50 27.00
Dimensions (mm) (H)145x(W)292x(D)382 (H)145 x (W)720x(D)382 (H)145x(W)292x(D)382 (H)145x(W)720x(D)382
Net Weight (kg) 3.7 6.6 3.7 6.6
Outer burner 1.65 1.65 0.95
Inner burner 0.70 0.70 0.45
Injector
size (mm) pilot 0.90 0.90 0.50
Gas Type NATURAL PROPANE
Gas Pressure (kPa) 1.00 2.75
Gas Fitting ¼” BSPM 600coned
Ignition System Piezo-electric
Country of Origin China
AGA Approval No. 7092G
Austcrown Pty. Ltd and their appointed agents will not be liable in respect of any misuse, which is not in accordance with the
instructions and precautions specified in this booklet.
AUSTCROWN PTY LTD
Website: www.auscrown.com.au
SERVICE AGENTS
For services and repairs, contact our service agent or any other authorised gas fitter and plumber.
Progress Plumbing and Gas Maintenance
16 Raymond Street, BLACKBURN VIC 3130
Ph: 9878 5845 Mobile: [phone]

AUSCROWN
www.auscrown.com.au

- Natural Gas or LP gas - Stainless Steel Body
- Piezo Ignition - Pans & Pots Compatible
- Indoor or Outdoor Use - BBQ Side Burner
- Alfresco Cooking - Adjustable Double Ring Flame
AUSCROWN
WITH
BEEHIVE
BURNER
CK107LP/RB18NG CK203LP/RB28NG
CK801NG RB18NG CK801PG CK107LP CK802NG RB28NG CK802PG CK203LP
15.8MJ/hr 14.2MJ/hr 13.5MJ/hr 12.5MJ/hr 2 x15.8MJ/hr 2 x14.2MJ/hr 2 x 13.5MJ/hr 2 x12.5MJ/hr
Outer Ring Ø0.95mm Ø0.90mm Ø0.95mm Ø0.90mm
Inner Ring Ø0.45mm Ø0.40mm Ø0.45mm Ø0.40mm
Pilot
Indoor Outdoor Indoor Outdoor
2.75kPa 1.0kPa 2.75kPa
Ø0.90mm Ø0.50mm Ø0.90mm Ø0.50mm
Ø1.65mm
Ø0.7mm
W720mmxD382mmxH145mm
6.53kg
Piezo-Electric
1/4" BSPM 60º Coned
Propane Gas Propane Gas
1.0kPa Natural Gas
Ø0.7mm
Ø1.65mm
Inlet Fitting
Country Of Origin
Dimensions
Natural Gas
W292mmxD382mmxH145mm
3.41kg
7092
China
Model
Heat Capacity
AGAApproval No
Net Weight
Ignition System
Gas Type
Gas Pressure
Injector Size
Operating Location
CK801PG/NG CK802PG/NG
Outer Ring High
Inner Ring High Outer Ring Low
Inner Ring High Outer Ring Low
Inner Ring Low Outer Ring Off
Inner Ring High Outer Ring Off
Inner Ring Low
WITH
BRASS CAP
BURNER
Ideal for Everyday Use

DUST CAP FOR GAS CYLINDER VALVE
STEP 1 STEP 2
STEP 3 FINISH
Cap with
POL Male Thread
Cap with
Female Thread
Cap with
No Thread
AUSCROWN
STAINLESS STEEL TABLE FOR COOKERSTAINLESS STEEL TABLE FOR COOKER
MaxLoad 50kg
Model SB602
Gross Weight
Dimensions (Overall) 6.7kg
W720mmxD520mmxH812mm
Can be used with
- Handy Range
- Single Wok Burner
- Double Wok Burner
- Rice Cooker
- High Pressurer Wok
Burner
- Portable Cast Iron
Burner
-
-
SB602
DISPOSABLE POL SEAL
Install
Remove

AUSCROWN Butane Gas HANDY RANGE
Features:
Portable / Piezo Ignition / Indoor or Outdoor / Light Weight / Easy to Use / Compact
Model AD90
Injector Size Ø0.55mm
Dimensions W343mm xD256mm xH111mm
AGAApproval No 5240
Gas Type Butane Gas
Gas Pressure Cartridge Pressure
Heat Capacity 7.0MJ/hr
Gas Consumption 150g/hr
Net Weight 1.7kg
Ignition System Piezo-Electric
238GM
BUTANE GAS CARTRIDGE
GP33 KOREAN BBQ GRILL PLATE
AD90
Features:
- 33cm diameter.
- Removable non-stick grill plate.
- Steam function.
- Enameled pan.
- Grill plate lifter included. Grill plate lifter included.
For convenient and safe
handling.
How it works
Steam action.
Keeps food moist & succulent when cooking.
Enamelled pan.
Collects excessive grease
and reduces smoke
* Handy Range Not Included. Removable non-stick
grill plate. Makes cooking
and cleaning easy.
KW707 BUTANE GAS BLOW TORCH
Product name Butane gas blow torch
Model KW707
Heat Capacity 1,325 Kcal/hr (1.54KW/hr)
Gas Consumption 125gm/hr
Jet Size 0.27mm Diameter
Burner Diameter 22.5mm
Dimensions (mm) 165 x 55 x 32
Net Weight 130gm
Gas Type AUSCROWN butane gas
Gas Pressure 2-3kg/cm2
Inlet Fitting AUSCROWN Butane gas canister nozzle type

AUSCROWN BRUSHED STAINLESS STEEL
CANOPY RANGE HOODS
Features:
Strong Suction / Brushed Stainless Steel Body / 3 Speed Control /
Micromesh Filters /Optional Charcoal Filter / Ducted or Re-circulated Exhaust
CS900 900MM CS600 600MM
CI900G 900MM ISLAND TYPE
WITH TEMPERED GLASSCI900 900MM ISLAND TYPE
C900GH 900MM CANOPY
WITH TEMPERED GLASS
X: Heigh when duct cover fully extended.
Model C900GH CS900 CS600 CI900 CI900G
Dimensions
W900mm
D475mm
H560mm
X950mm
W900mm
D480mm
H520mm
X910mm
W600mm
D480mm
H520mm
X910mm
W895mm
D600mm
H637mm
X1204mm
W895mm
D600mm
H613mm
X1180mm
Net Weight 21kg 22kg 17kg 27kg 29kg
Lamp Power
Flow Rate
Load of Motor
Duct Size
C tick Approval
AS Approval
Power
No. of Motor 240V60Hz
1
V06076/0
N2788
1000m³/hr
2 x2W
Ø150mm
4 x2W
250W

PORTABLE FOR OUTDOOR USE WITH LP GAS BOTTLE
RamboRambo
Model HPA100LPB RH31LT HP200LPB
Dimensions W320mm xL520mm xH160mm W330mm xL490mm xH180mm W415mm xL690mm xH220mm
Net Weight 6.6kg 7.7kg 14.9kg
Injector Size Burner :Ø0.90mm
Pilot: Ø0.45mm Burner: Ø0.90mm Pilot: Ø0.25mm
Outer Ring: Ø0.1.2mm
Inner Ring: Ø0.55mm
Pilot: Ø0.25mm
Ignition System Piezo Electric Manual with Pilot Manual with Pilot
Gas Pressure 61kPa
Heat Capacity 64MJ/hr
Gas Consumption 1.6kg/hr
Gas Type
Inlet Fitting 1/4" BSPM60º Coned
Propane
55MJ/hr
100kPa
1.0kg/hr
COMPLETE WITH HOSE & REGULATORCOMPLETE WITH HOSE & REGULATOR
WITH AUTOMATIC IGNITION
Low PressureLow Pressure
COMPLETE WITH HOSE & REGULATORCOMPLETE WITH HOSE & REGULATOR
RBC176LP RBC225LP
20MJ/hr 32MJ/hr
0.42kg/hr 0.64kg/hr
Inner Ring Ø0.65mm Ø0.90mm
Outer Ring Ø1.20mm Ø1.30mm
Pilot Ø0.60mm Ø0.6mm
W290mm xD540mm xH130mm W350mm xD600mm xH140mm
5.16kg 6.6kg
Approval No. IAPMO R&T OCEANA GMK10042
Net Weight
Inlet Fitting 1/4" BSPM60º Coned
Country of Origin
ULP gas
2.75kPa
Piezo Electric
China
Injector
Size
Gas Consumption
Model
Gas Pressure
Heat Capacity
Gas Type
Ignition System
Dimensions
RH31LT with pilotRH31LT with pilot HP200LPB 2 ring high with pilotHP200LPB 2 ring high with pilot HPA100LPB with auto ignitionHPA100LPB with auto ignition
Powerful Heat CapacityPowerful Heat Capacity
RH31LT & HP200LPB
for overseas only
not for Australia
FOR OVERSEAS MARKET ONLY FOR OVERSEAS MARKET ONLY
PORTABLE
FOR OUTDOOR USE
WITH LP GAS BOTTLE
PORTABLE
FOR OUTDOOR USE
WITH LP GAS BOTTLE
DUAL RING CONTROLDUAL RING CONTROL

AUSCROWN LOW PRESSURE
CAST IRON RING BURNER
Features:
High Heat Capacity / Portable / Ideal for Outdoor Cooking / Individual Ring Control
*Burners Not Included
FRAME FOR CAST IRON RING BURNER
Features: Portable / Ideal for Stockpot Cooking
C20LP C30LP C40LP C50LP
Model C20LP C30LP C40LP C50LP
Number of Rings 1 2 3 4
Heat Capacity 12MJ/hr 20MJ/hr 30MJ/hr 52MJ/hr
Gas Consumption 0.26kg/hr 0.44kg/hr 0.65kg/hr 1.28kg/hr
Injector Size Ø1.0mm 1st Ring: Ø0.7mm
2nd Ring: Ø1.1mm
1st Ring: Ø0.50mm
2nd Ring: Ø0.90mm
3rd Ring: Ø1.20mm
1st Ring: Ø0.50mm
2nd Ring: Ø0.80mm
3rd Ring: Ø1.05mm
4th Ring: Ø1.50mm
Dimensions W190mm
L370mm
H85mm
W185mm
L420mm
H85mm
W250mm
L470mm
H95mm
W360mm
L635mm
H110mm
Net Weight 1.82kg 3.2kg 6.2kg 12.8kg
Gas Type
Gas Pressure
Ignition System
Inlet Fitting
AGAApproval No 6429
Propane Gas
2.75kPa
Manual
1/4" BSPM60º Coned
Supplied with
AGA approved
regulator & 1.2 meter hose
FF30 FF40 FF50
C30LP C40LP C50LP
W378mm xD378mm xH175mm W430mm xD430mm xH175mm W530mm xD530mm xH175mm
5.6kg 6.6kg 8.8kg
Ø458mm Ø510mm Ø610mm
Ø378mm Ø430mm Ø530mm
Model
Dimensions
Net Weight
Minimum Pot Size
Maximum Pot Size
Suit for
FF30
C30LP
+=
FF30
Rings can be operated individually

AUSCROWN
GAS LIGHTERS / PIEZO IGNITOR
SL160
PIEZO ELECTRIC
IGNITOR
BBQL CAST IRON BBQ LONG BURNER
Overall Length: 40.5cm
Burner Length: 35cm
Burner Width: 7.8cm
Inlet Size: Ø1.3cm
N.W.: 1.9kg
GM28
BUTANE GAS MATCH
WITH CHILD SAFETY LOCK
Ideal for Manual Ignition Gas Appliances
CAST IRON LOW PRESSURE COUNTRY COOKER
GB01LP 1 burner GB02LP 2 burners GB03LP 3 burners
FOR OUTDOOR USE ONLY
Features: Portable / Ideal for Outdoor Cooking / Double Ring Burner
Supplied with Hose and Regulator
Ring Burner Country Cooker
JZDD17
PIEZO ELECTRIC
IGNITOR
Model GB01LP GB02LP GB03LP
Heat Capacity 12MJ/hr 2 x12MJ/hr 3 x12MJ/hr
Gas Consumption 0.26kg/hr 2 x0.26kg/hr 3 x0.26kg/hr
Dimensions (mm) W270 xD350xH140 W520 xD350 xH140 W770 xD350 xH140
Net Weight 3.20kg 5.5kg 8.7kg
Gas Type
Gas Pressure
Injector Size
Ignition System
Gas Inlet Fitting
AGAApproval No
Country of Origin China
Ø1.0mm
Manual
1/4" BSPM60º Coned
Propane Gas
2.75kPa
6327